Octave-spanning supercontinuum generation in a CMOS-compatible thin Si3N4 waveguide coated with highly nonlinear TeO2.

Supercontinuum generation (SCG) is an important nonlinear optical process enabling broadband light sources for many applications, for which silicon nitride (Si3N4) has emerged as a leading on-chip platform. To achieve suitable group velocity dispersion and high confinement for broadband SCG the Si3N4 waveguide layer used is typically thick (>∼700 nm), which can lead to high stress and cracks unless specialized processing steps are used. Here, we report on efficient octave-spanning SCG in a thinner moderate-confinement 400-nm Si3N4 platform using a highly nonlinear tellurium oxide (TeO2) coating. An octave supercontinuum spanning from 0.89 to 2.11 µm is achieved at a low peak power of 258 W using a 100-fs laser centered at 1565 nm. Our numerical simulations agree well with the experimental results giving a nonlinear parameter of 2.5 ± 0.5 W-1m-1, an increase by a factor of 2.5, when coating the Si3N4 waveguide with a TeO2 film. This work demonstrates highly efficient SCG via effective dispersion engineering and an enhanced nonlinearity in CMOS-compatible hybrid TeO2-Si3N4 waveguides and a promising route to monolithically integrated nonlinear, linear, and active functionalities on a single silicon photonic chip.

Silicon-thulium hybrid microdisk lasers with low threshold and wide emission wavelength range.

We demonstrate low-threshold and wide emission wavelength range hybrid-integrated silicon-thulium microdisk lasers based on a pulley-coupled design. The resonators are fabricated on a silicon-on-insulator platform using a standard foundry process and the gain medium is deposited using a straightforward, low-temperature post-processing step. We show lasing in 40- and 60-µm diameter microdisks with up to 2.6 mW double-sided output power and bidirectional slope efficiencies of up to 13.4% with respect to 1620 nm pump power launched to the bus waveguides. We observe thresholds less than 1 mW versus on-chip pump power and both single-mode and multimode laser emission spanning across wavelengths from 1825 to 1939nm. These low threshold lasers with emissions over a > 100 nm range open the door to monolithic silicon photonic integrated circuits with broadband optical gain and highly compact and efficient light sources in the emerging ∼1.8-2.0 µm wavelength band.

Hybrid silicon-tellurium-dioxide DBR resonators coated in PMMA for biological sensing.

We report on silicon waveguide distributed Bragg reflector (DBR) cavities hybridized with a tellurium dioxide (TeO2) cladding and coated in plasma functionalized poly (methyl methacrylate) (PMMA) for label free biological sensors. We describe the device structure and fabrication steps, including reactive sputtering of TeO2 and spin coating and plasma functionalization of PMMA on foundry processed Si chips, as well as the characterization of two DBR designs via thermal, water, and bovine serum albumin (BSA) protein sensing. Plasma treatment on the PMMA films was shown to decrease the water droplet contact angle from ∼70 to ∼35°, increasing hydrophilicity for liquid sensing, while adding functional groups on the surface of the sensors intended to assist with immobilization of BSA molecules. Thermal, water and protein sensing were demonstrated on two DBR designs, including waveguide-connected sidewall (SW) and waveguide-adjacent multi-piece (MP) gratings. Limits of detection of 60 and 300 × 10-4 RIU were measured via water sensing, and thermal sensitivities of 0.11 and 0.13 nm/°C were measured from 25-50 °C for SW and MP DBR cavities, respectively. Plasma treatment was shown to enable protein immobilization and sensing of BSA molecules at a concentration of 2 µg/mL diluted in phosphate buffered saline, demonstrating a ∼1.6 nm resonance shift and subsequent full recovery to baseline after stripping the proteins with sodium dodecyl sulfate for a MP DBR device. These results are a promising step towards active and laser-based sensors using rare-earth-doped TeO2 in silicon photonic circuits, which can be subsequently coated in PMMA and functionalized via plasma treatment for label free biological sensing.

Application of the TDFA window in true optical time delay systems.

Recent advances in silicon photonic components operating in the thulium-doped fiber amplifier (TDFA) wavelength regime around 2-µm have shown that these wavelengths hold great promise for on-chip photonic systems. Here we present our work on characterizing a Mach-Zehnder interferometer coupled silicon photonic ring resonator operating in the TDFA window for optical time delay applications. We describe the optical transmission and variable time delay properties of the resonator, including a detailed characterization and comparison of the directional coupler and Mach-Zehnder interferometer base components at both 1930 and 1550 nm wavelengths. The results show tuning of a ring from a 190-ps peak time delay at a resonant extinction ratio of 5.1-dB to a 560-ps peak time delay at an extinction ratio of 11.0-dB, in good agreement with optical models of the device. These results demonstrate significant promise towards the future application of TDFA band devices in optical time delay systems.

Thulium-doped tellurium oxide waveguide amplifier with 7.6 dB net gain on a silicon nitride chip: publisher's note.

This publisher's note contains corrections to Opt. Lett.44, 5788 (2019)OPLEDP0146-959210.1364/OL.44.005788.

Erbium-ytterbium co-doped aluminium oxide waveguide amplifiers fabricated by reactive co-sputtering and wet chemical etching.

We report on the fabrication and optical characterization of erbium-ytterbium co-doped aluminum oxide (Al2O3:Er3+:Yb3+) waveguides using low-cost, low-temperature deposition and etching steps. We deposited Al2O3:Er3+:Yb3+ films using reactive co-sputtering, with Er3+ and Yb3+ ion concentrations ranging from 1.4-1.6 × 1020 and 0.9-2.1 × 1020 ions/cm3, respectively. We etched ridge waveguides in 85% pure phosphoric acid at 60°C, allowing for structures with minimal polarization sensitivity and acceptable bend radius suitable for optical amplifiers and avoiding alternative etching chemistries which use hazardous gases. Scanning-electron-microscopy (SEM) and profilometry were used to assess the etch depth, sidewall roughness, and facet profile of the waveguides. The Al2O3:Er3+:Yb3+ films exhibit a background loss as low as 0.2 ± 0.1 dB/cm and the waveguide loss after structuring is determined to be 0.5 ± 0.3 dB/cm at 1640 nm. Internal net gain of 4.3 ± 0.9 dB is demonstrated at 1533 nm for a 3.0 cm long waveguide when pumped at 970 nm. The material system is promising moving forward for compact Er-Yb co-doped waveguide amplifiers and lasers on a low-cost silicon wafer-scale platform.

Subwavelength grating metamaterial waveguides functionalized with tellurium oxide cladding.

We report on the design, fabrication and characterization of subwavelength grating metamaterial waveguides coated with tellurium oxide. The structures are first fabricated using a standard CMOS compatible process on a silicon-on-insulator platform. Amorphous tellurium oxide top cladding material is then deposited via post-process RF magnetron sputtering. The photonic bandstructure is controlled by adjustment of the device geometry, opening a wide range of operating regimes, including subwavelength propagation, slow light and the photonic bandgap, for various wavelength bands within the 1550 nm telecommunications window. Propagation loss of 1.0 ± 0.1 dB/mm is reported for the tellurium oxide-cladded device, compared to 1.5 ± 0.1 dB/mm propagation loss reported for the silicon dioxide-cladded reference structure. This is the first time that a high-index (n > 2) oxide cladding has been demonstrated for subwavelength grating metamaterial waveguides, thus introducing a new material platform for on-chip integrated optics.

A Silicon Photonic Data Link with a Monolithic Erbium-Doped Laser.

To meet the increasing demand for data communication bandwidth and overcome the limits of electrical interconnects, silicon photonic technology has been extensively studied, with various photonics devices and optical links being demonstrated. All of the optical data links previously demonstrated have used either heterogeneously integrated lasers or external laser sources. This work presents the first silicon photonic data link using a monolithic rare-earth-ion-doped laser, a silicon microdisk modulator, and a germanium photodetector integrated on a single chip. The fabrication is CMOS compatible, demonstrating data transmission as a proof-of-concept at kHz speed level, and potential data rate of more than 1 Gbps. This work provides a solution for the monolithic integration of laser sources on the silicon photonic platform, which is fully compatible with the CMOS fabrication line, and has potential applications such as free-space communication and integrated LIDAR.

Thulium-doped tellurium oxide waveguide amplifier with 7.6 dB net gain on a silicon nitride chip.

We report on thulium-doped waveguide amplifiers integrated on a low-loss silicon nitride platform. The amplifier structure consists of a thulium-doped tellurium oxide thin film coated on a silicon nitride strip waveguide on silicon. We determine a waveguide background loss of 0.7 dB/cm at 1479 nm based on the quality factor measured in microring resonators. Gain measurements were carried out in straight and 6.7-cm-long s-bend waveguides realized on a 2.2-cm-long chip. We measure internal net gain over the wavelength range 1860-2000 nm under 1620 nm pumping and up to 7.6 dB total gain at 1870 nm, corresponding to 1.1 dB/cm. These results are promising for the realization of highly compact thulium-doped amplifiers in the emerging 2 µm band for silicon-based photonic microsystems.

Low-loss TeO2-coated Si3N4 waveguides for application in photonic integrated circuits.

We report on high-quality tellurium oxide waveguides integrated on a low-loss silicon nitride wafer-scale platform. The waveguides consist of silicon nitride strip features, which are fabricated using a standard foundry process and a tellurium oxide coating layer that is deposited in a single post-processing step. We show that by adjusting the Si3N4 strip height and width and TeO2 layer thickness, a small mode area, small bend radius and high optical intensity overlap with the TeO2 can be obtained. We investigate transmission at 635, 980, 1310, 1550 and 2000 nm wavelengths in paperclip waveguide structures and obtain low propagation losses down to 0.6 dB/cm at 2000 nm. These results illustrate the potential for compact linear, nonlinear and active tellurite glass devices in silicon nitride photonic integrated circuits operating from the visible to mid-infrared.

High-Q tellurium-oxide-coated silicon nitride microring resonators.

We report on tellurium-oxide (TeO2)-coated silicon nitride microring resonators with internal quality factors up to 7.3×105, corresponding to 0.5 dB/cm waveguide loss, at wavelengths around 1550 nm. The microring resonators are fabricated using a silicon nitride foundry process followed by TeO2 coating deposition in a single post-processing step. The silicon nitride strip height of 0.2 µm enables a small microring bending radius, while the TeO2 coating thickness of 0.33 µm results in a large modal overlap with the TeO2 layer. These results are a promising step towards realizing compact and high-performance linear, nonlinear, and rare-earth-doped active integrated photonic devices with this platform.

A Tellurium Oxide Microcavity Resonator Sensor Integrated On-Chip with a Silicon Waveguide.

We report on thermal and evanescent field sensing from a tellurium oxide optical microcavity resonator on a silicon photonics platform. The on-chip resonator structure is fabricated using silicon-photonics-compatible processing steps and consists of a silicon-on-insulator waveguide next to a circular trench that is coated in a tellurium oxide film. We characterize the device's sensitivity by both changing the temperature and coating water over the chip and measuring the corresponding shift in the cavity resonance wavelength for different tellurium oxide film thicknesses. We obtain a thermal sensitivity of up to 47 pm/°C and a limit of detection of 2.2 × 10-3 RIU for a device with an evanescent field sensitivity of 10.6 nm/RIU. These results demonstrate a promising approach to integrating tellurium oxide and other novel microcavity materials into silicon microphotonic circuits for new sensing applications.

Optically pumped rare-earth-doped Al2O3 distributed-feedback lasers on silicon [Invited].

This paper reviews recent progress in the field of optically pumped rare-earth-doped channel waveguide lasers, with a focus on operation utilizing distributed-feedback resonators on silicon wafers. Rare-earth-doped amorphous aluminum oxide thin films have been deposited onto silicon wafers by RF reactive co-sputtering from metallic Al and rare-earth targets, the spectroscopy and optical gain of Er3+, Yb3+, Nd3+, and Tm3+ ions has been investigated, and the near-infrared laser transitions near 1 µm in Yb3+, 1.5 µm in Er3+, and 2 µm in Tm3+ and Ho3+ have been demonstrated. Output power between a few µW and hundreds of mW have been achieved in different waveguide geometries, and ultranarrow-linewidth laser operation has been demonstrated.

High-Q-factor Al2O3 micro-trench cavities integrated with silicon nitride waveguides on silicon.

We report on the design and performance of high-Q integrated optical micro-trench cavities on silicon. The microcavities are co-integrated with silicon nitride bus waveguides and fabricated using wafer-scale silicon-photonics-compatible processing steps. The amorphous aluminum oxide resonator material is deposited via sputtering in a single straightforward post-processing step. We examine the theoretical and experimental optical properties of the aluminum oxide micro-trench cavities for different bend radii, film thicknesses and near-infrared wavelengths and demonstrate experimental Q factors of > 106. We propose that this high-Q micro-trench cavity design can be applied to incorporate a wide variety of novel microcavity materials, including rare-earth-doped films for microlasers, into wafer-scale silicon photonics platforms.

Broadband 2-µm emission on silicon chips: monolithically integrated Holmium lasers.

Laser sources in the mid-infrared are of great interest due to their wide applications in detection, sensing, communication and medicine. Silicon photonics is a promising technology which enables these laser devices to be fabricated in a standard CMOS foundry, with the advantages of reliability, compactness, low cost and large-scale production. In this paper, we demonstrate a holmium-doped distributed feedback laser monolithically integrated on a silicon photonics platform. The Al2O3:Ho3+ glass is used as gain medium, which provides broadband emission around 2 µm. By varying the distributed feedback grating period and Al2O3:Ho3+ gain layer thickness, we show single mode laser emission at wavelengths ranging from 2.02 to 2.10 µm. Using a 1950 nm pump, we measure a maximum output power of 15 mW, a slope efficiency of 2.3% and a side-mode suppression ratio in excess of 50 dB. The introduction of a scalable monolithic light source emitting at > 2 µm is a significant step for silicon photonic microsystems operating in this highly promising wavelength region.

Ultra-narrow-linewidth Al2O3:Er3+ lasers with a wavelength-insensitive waveguide design on a wafer-scale silicon nitride platform.

We report ultra-narrow-linewidth erbium-doped aluminum oxide (Al2O3:Er3+) distributed feedback (DFB) lasers with a wavelength-insensitive silicon-compatible waveguide design. The waveguide consists of five silicon nitride (SiNx) segments buried under silicon dioxide (SiO2) with a layer Al2O3:Er3+ deposited on top. This design has a high confinement factor (> 85%) and a near perfect (> 98%) intensity overlap for an octave-spanning range across near infra-red wavelengths (950-2000 nm). We compare the performance of DFB lasers in discrete quarter phase shifted (QPS) cavity and distributed phase shifted (DPS) cavity. Using QPS-DFB configuration, we obtain maximum output powers of 0.41 mW, 0.76 mW, and 0.47 mW at widely spaced wavelengths within both the C and L bands of the erbium gain spectrum (1536 nm, 1566 nm, and 1596 nm). In a DPS cavity, we achieve an order of magnitude improvement in maximum output power (5.43 mW) and a side mode suppression ratio (SMSR) of > 59.4 dB at an emission wavelength of 1565 nm. We observe an ultra-narrow linewidth of ΔνDPS = 5.3 ± 0.3 kHz for the DPS-DFB laser, as compared to ΔνQPS = 30.4 ± 1.1 kHz for the QPS-DFB laser, measured by a recirculating self-heterodyne delayed interferometer (R-SHDI).

Monolithically-integrated distributed feedback laser compatible with CMOS processing.

An optically-pumped, integrated distributed feedback laser is demonstrated using a CMOS compatible process, where a record-low-temperature deposited gain medium enables integration with active devices such as modulators and detectors. A pump threshold of 24.9 mW and a slope efficiency of 1.3 % is demonstrated at the lasing wavelength of 1552.98 nm. The rare-earth-doped aluminum oxide, used as the gain medium in this laser, is deposited by a substrate-bias-assisted reactive sputtering process. This process yields optical quality films with 0.1 dB/cm background loss at the deposition temperature of 250 °C, and therefore is fully compatible as a back-end-of-line CMOS process. The aforementioned laser's performance is comparable to previous lasers having gain media fabricated at much higher temperatures (> 550 °C). This work marks a crucial step towards monolithic integration of amplifiers and lasers in silicon microphotonic systems.

Athermal synchronization of laser source with WDM filter in a silicon photonics platform.

In an optical interconnect circuit, microring resonators (MRRs) are commonly used in wavelength division multiplexing systems. To make the MRR and laser synchronized, the resonance wavelength of the MRR needs to be thermally controlled, and the power consumption becomes significant with a high-channel count. Here, we demonstrate an athermally synchronized rare-earth-doped laser and MRR. The laser comprises a Si3N4 based cavity covered with erbium-doped Al2O3 to provide gain. The low thermo-optic coefficient of Al2O3 and Si3N4 and the comparable thermal shift of the effective index in the laser and microring cross-sections enable lasing and resonance wavelength synchronization over a wide range of temperatures. The power difference between matched and unmatched channels remains greater than 15 dB from 20 to 50 °C due to a synchronized wavelength shift of 0.02 nm/°C. The athermal synchronization approach reported here is not limited to microring filters but can be applied to any Si3N4 filter with integrated lasers using rare earth ion doped Al2O3 as a gain medium to achieve system-level temperature control free operation.

Wavelength division multiplexed light source monolithically integrated on a silicon photonics platform.

We demonstrate monolithic integration of a wavelength division multiplexed light source for silicon photonics by a cascade of erbium-doped aluminum oxide (Al2O3:Er3+) distributed feedback (DFB) lasers. Four DFB lasers with uniformly spaced emission wavelengths are cascaded in a series to simultaneously operate with no additional tuning required. A total output power of -10.9 dBm is obtained from the four DFBs with an average side mode suppression ratio of 38.1±2.5 dB. We characterize the temperature-dependent wavelength shift of the cascaded DFBs and observe a uniform dλ/dT of 0.02 nm/°C across all four lasers.

High-power thulium lasers on a silicon photonics platform.

Mid-infrared laser sources are of great interest for various applications, including light detection and ranging, spectroscopy, communication, trace-gas detection, and medical sensing. Silicon photonics is a promising platform that enables these applications to be integrated on a single chip with low cost and compact size. Silicon-based high-power lasers have been demonstrated at 1.55 µm wavelength, while in the 2 µm region, to the best of our knowledge, high-power, high-efficiency, and monolithic light sources have been minimally investigated. In this Letter, we report on high-power CMOS-compatible thulium-doped distributed feedback and distributed Bragg reflector lasers with single-mode output powers up to 267 and 387 mW, and slope efficiencies of 14% and 23%, respectively. More than 70 dB side-mode suppression ratio is achieved for both lasers. This work extends the applicability of silicon photonic microsystems in the 2 µm region.