Antioxidant Activity of the Lignins Derived from Fluidized-Bed Fast Pyrolysis.

A challenge in recent years has been the rational use of forest and agriculture residues for the production of bio-fuel, biochemical, and other bioproducts. In this study, potentially useful compounds from pyrolytic lignins were identified by HPLC-MS/MS and untargeted metabolomics. The metabolites identified were 2-(4-allyl-2-methoxyphenoxy)-1-(4-hydroxy-3-methoxyphenyl)-1-propanol, benzyl benzoate, fisetinidol, phenyllactic acid, 2-phenylpropionic acid, 6,3'-dimethoxyflavone, and vanillin. The 2,2-diphenyl-1-picrylhydrazyl radical scavenging activity (DPPH), trolox equivalent antioxidant capacity (TEAC), and total phenolics content (TPC) per gram of pyrolytic lignin ranged from 14 to 503 mg ascorbic acid equivalents, 35 to 277 mg trolox equivalents, and 0.42 to 50 mg gallic acid equivalents, respectively. A very significant correlation was observed between the DPPH and TPC (r = 0.8663, p ≤ 0.0001), TEAC and TPC (r = 0.8044, p ≤ 0.0001), and DPPH and TEAC (r = 0.8851, p ≤ 0.0001). The polyphenolic compounds in the pyrolytic lignins which are responsible for radical scavenging activity and antioxidant properties can be readily profiled with HPLC-MS/MS combined with untargeted metabolomics. The results also suggest that DPPH, TEAC, and TPC assays are suitable methods for the measurement of antioxidant activity in a variety of pyrolytic lignins. These data show that the pyrolytic lignins can be considered as promising sources of natural antioxidants and value-added chemicals.

Application of 1D and 2D MFR reactor technology for the isolation of insecticidal and anti-microbial properties from pyrolysis bio-oils.

Valuable chemicals can be separated from agricultural residues by chemical or thermochemical processes. The application of pyrolysis has already been demonstrated as an efficient means to produce a liquid with a high concentration of desired product. The objective of this study was to apply an insect and microorganism bioassay-guided approach to separate and isolate pesticidal compounds from bio-oil produced through biomass pyrolysis. Tobacco leaf (Nicotianata bacum), tomato plant (Solanum lycopersicum), and spent coffee (Coffea arabica) grounds were pyrolyzed at 10°C/min from ambient to 565°C using the mechanically fluidized reactor (MFR). With one-dimensional (1D) MFR pyrolysis, the composition of the product vapors varied as the reactor temperature was raised allowing for the selection of the temperature range that corresponds to vapors with a high concentration of pesticidal properties. Further product separation was performed in a fractional condensation train, or 2D MFR pyrolysis, thus allowing for the separation of vapor components according to their condensation temperature. The 300-400°C tobacco and tomato bio-oil cuts from the 1D MFR showed the highest insecticidal and anti-microbial activity compared to the other bio-oil cuts. The 300-350 and 350-400°C bio-oil cuts produced by 2D MFR had the highest insecticidal activity when the bio-oil was collected from the 210°C condenser. The tobacco and tomato bio-oil had similar insecticidal activity (LC50 of 2.1 and 2.2 mg/mL) when the bio-oil was collected in the 210°C condenser from the 300-350°C reactor temperature gases. The 2D MFR does concentrate the pesticidal products compared to the 1D MFR and thus can reduce the need for further separation steps such as solvent extraction.

Improved lignin pyrolysis for phenolics production in a bubbling bed reactor--Effect of bed materials.

Lignin pyrolysis was studied in a bubbling fluidized bed reactor equipped with a fractional condensation train, using nitrogen as the fluidization gas. The effect of different bed materials (silica sand, lignin char, activated lignin char, birch bark char, and foamed glass beads) on bio-oil yield and quality was investigated for a pyrolysis temperature of 550 °C. Results how that a bed of activated lignin char is preferable to the commonly used silica sand: pyrolysis of Kraft lignin with a bed of activated lignin char not only provides a pure char product, but also a higher dry bio-oil yield (with a relative increase of 43%), lower pyrolytic water production, and better bio-oil quality. The bio-oil obtained from Kraft lignin pyrolysis with a bed of activated lignin char has a lower average molecular weight, less tar, more phenolics, and less acidity than when sand is used as bed material.

Insecticidal activity of bio-oil from the pyrolysis of straw from Brassica spp.

Agricultural crop residues can be converted through thermochemical pyrolysis to bio-oil, a sustainable source of biofuel and biochemicals. The pyrolysis bio-oil is known to contain many chemicals, some of which have insecticidal activity and can be a potential source of value-added pest control products. Brassicacae crops, cabbage, broccoli, and mustards, contain glucosinolates and isocyanates, compounds with recognized anti-herbivore activity. In Canada, canola Brassica napus straw is available from over 6 000 000 ha and mustard Brassica carinata and Brassica juncea straw is available from 200 000 ha. The straw can be converted by microbial lignocellulosic enzymes as a substrate for bioethanol production but can also be converted to bio-oil by thermochemical means. Straw from all three species was pyrolyzed, and the insecticidal components in the bio-oil were isolated by bioassay-guided solvent fractionation. Of particular interest were the mustard straw bio-oil aqueous fractions with insecticidal and feeding repellent activity to Colorado potato beetle larvae. Aqueous fractions further analyzed for active compounds were found not to contain many of the undesirable phenol compounds, which were previously found in other bio-oils seen in the dichloromethane (DCM) and ethyl acetate (EA) solvent phases of the present study. Identified within the most polar fractions were hexadecanoic and octadecanoic fatty acids, indicating that separation of these compounds during bio-oil production may provide a source of effective insecticidal compounds.

Detection of the breakage of pharmaceutical tablets in pneumatic transport.

Pneumatic transport of pharmaceutical tablets is very convenient, compact and greatly reduces contamination. A potential problem, however, is the breakage of a significant fraction of the transported tablets, causing serious product quality problems. Since the flowrate of tablets transported through a given pneumatic transport line increases with gas velocity, lines are often operated at gas velocities slightly below the velocity at which tablets break. Minor changes in operating conditions can have a large effect on the impact resistance of tablets and on the observed tablet breakage rate. Therefore, maintaining a constant gas velocity is not sufficient to keep the tablet breakage rate below an acceptable level. The objective of the present study was to develop a reliable and non-invasive on-line method for the detection of tablet breakage. Pharmaceutical acetaminophen tablets were transported pneumatically in a 0.1 m diameter pipeline consisting of a 5 m vertical and a 4.0 m horizontal section made of either re-enforced PVC or steel. The pipeline flow regime was determined by visual observation through clear pipeline sections. Tablet breakage was quantified by screening tablet samples. Acoustic measurements were recorded at different locations along the pipeline. Analysis of the signals from microphones attached to the wall of the elbow and horizontal section provided a reliable detection of conditions leading to tablet breakage.