Rubrene single crystal solar cells and the effect of crystallinity on interfacial recombination.

Single crystal studies provide a better understanding of the basic properties of organic photovoltaic devices. Therefore, in this work, rubrene single crystals with a thickness of 250 nm to 1000 nm were used to produce an inverted bilayer organic solar cell. Subsequently, polycrystalline rubrene (orthorhombic, triclinic) and amorphous bilayer solar cells of the same thickness as single crystals were studied to make comparisons across platforms. To investigate how single crystal, polycrystalline (triclinic-orthorhombic) and amorphous forms alter the charge carrier recombination mechanism at the rubrene/PCBM interface, light intensity measurements were carried out. The light intensity dependency of the JSC, VOC and FF parameters in organic solar cells with different forms of rubrene was determined. Monomolecular (Shockley Read Hall) recombination is observed in devices employing amorphous and polycrystalline rubrene in addition to bimolecular recombination, whereas the single crystal device is weakly affected by trap assisted SRH recombination due to reduced trap states at the donor acceptor interface. To date, the proposed work is the only systematic study examining transport and interface recombination mechanisms in organic solar cells produced by different structure forms of rubrene.

Orienting and shaping organic semiconductor single crystals through selective nanoconfinement.

For organic semiconductor crystals exhibiting anisotropic charge transport along different crystallographic directions, nanoconfinement is a powerful strategy to control crystal orientation by aligning the fast crystallographic growth direction(s) with the unconfined axis(es) of nanoconfining scaffolds. Here, design rules are presented to relate crystal morphology, scaffold geometry, and orientation control in solution-processed small-molecule crystals. Specifically, organic semiconductor triisopropylsilylethynyl pyranthrene needle-like crystals with a dimensionality of n = 1 and perylene platelike crystals with n = 2 were grown from solution within nanoconfining scaffolds comprising cylindrical nanopores with a dimensionality of m = 1, representing one unconfined dimension along the cylinder axis, and those comprising nanopillar arrays with a dimensionality of m = 2. For m = n systems, native crystal growth habits were preserved while the crystal orientation in n = m direction(s) was dictated by the geometry of the scaffold. For n≠m systems, on the other hand, orientation control was restricted within a single plane, either parallel or perpendicular to the substrate surface. Intriguingly, control over crystal shape was also observed for perylene crystals grown in cylindrical nanopores (n > m). Within the nanopores, crystal growth was restricted along a single direction to form a needle-like morphology. Once growth proceeded above the scaffold surface, the crystals adopted their native growth habit to form asymmetric T-shaped single crystals with concave corners. These findings suggest that nanoporous scaffolds with spatially-varying dimensionalities can be used to grow single crystals of complex shapes.

Vibrational Excitation Mechanism in Tunneling Spectroscopy beyond the Franck-Condon Model.

Vibronic spectra of molecules are typically described within the Franck-Condon model. Here, we show that highly resolved vibronic spectra of large organic molecules on a single layer of MoS_{2} on Au(111) show spatial variations in their intensities, which cannot be captured within this picture. We explain that vibrationally mediated perturbations of the molecular wave functions need to be included into the Franck-Condon model. Our simple model calculations reproduce the experimental spectra at arbitrary position of the scanning tunneling microscope's tip over the molecule in great detail.

A Large Anisotropic Enhancement of the Charge Carrier Mobility of Flexible Organic Transistors with Strain: A Hall Effect and Raman Study.

Utilizing the intrinsic mobility-strain relationship in semiconductors is critical for enabling strain engineering applications in high-performance flexible electronics. Here, measurements of Hall effect and Raman spectra of an organic semiconductor as a function of uniaxial mechanical strain are reported. This study reveals a very strong, anisotropic, and reversible modulation of the intrinsic (trap-free) charge carrier mobility of single-crystal rubrene transistors with strain, showing that the effective mobility of organic circuits can be enhanced by up to 100% with only 1% of compressive strain. Consistently, Raman spectroscopy reveals a systematic shift of the low-frequency Raman modes of rubrene to higher (lower) frequencies with compressive (tensile) strain, which is indicative of a reduction (enhancement) of thermal molecular disorder in the crystal with strain. This study lays the foundation of the strain engineering in organic electronics and advances the knowledge of the relationship between the carrier mobility, low-frequency vibrational modes, strain, and molecular disorder in organic semiconductors.

Short Excited-State Lifetimes Enable Photo-Oxidatively Stable Rubrene Derivatives.

A series of rubrene derivatives were synthesized and the influence of the side group in enhancing photo-oxidative stability was evaluated. Photo-oxidation half-lives were determined via UV-vis absorption spectroscopy, which revealed thiophene containing derivatives to be the most stable species. The electron affinity of the compounds did not correlate with stability as previously reported in literature. Our work shows that shorter excited-state lifetimes result in increased photo-oxidative stability in these rubrene derivatives. These results confirm that faster relaxation kinetics out-compete the formation of reactive oxygen species that ultimately degrade linear oligoacenes. This report highlights the importance of using molecular design to tune excited-state lifetimes in order to generate more stable oligoacenes.

Three-Dimensional CeO2 Woodpile Nanostructures To Enhance Performance of Enzymatic Glucose Biosensors.

Fabrication of detection elements with ultrahigh surface area is essential for improving the sensitivity of analyte detection. Here, we report a direct patterning technique to fabricate three-dimensional CeO2 nanoelectrode arrays for biosensor application over relatively large areas. The fabrication approach, which employs nanoimprint lithography and a CeO2 nanoparticle-based ink, enables the direct, high-throughput patterning of nanostructures and is scalable, integrable, and of low cost. With the convenience of sequential imprinting, multilayered woodpile nanostructures with prescribed numbers of layers were achieved in a "stacked-up" architecture and were successfully fabricated over large areas. To demonstrate application as a biosensor, an enzymatic glucose sensor was developed. The sensitivity of glucose sensors can be enhanced simply by increasing the number of layers, which multiplies surface area while maintaining a constant footprint. The four-layer woodpile nanostructure of CeO2 glucose sensor exhibited enhanced sensitivity (42.8 µA mM-1 cm-2) and good selectivity. This direct imprinting strategy for three-dimensional sensing architectures is potentially extendable to other electroactive materials and other sensing applications.

Efficient Electron Mobility in an All-Acceptor Napthalenediimide-Bithiazole Polymer Semiconductor with Large Backbone Torsion.

An all-acceptor napthalenediimide-bithiazole-based co-polymer, P(NDI2OD-BiTz), was synthesized and characterized for application in thin-film transistors. Density functional theory calculations point to an optimal perpendicular dihedral angle of 90° between acceptor units along isolated polymer chains; yet optimized transistors yield electron mobility of 0.11 cm2/(V s) with the use of a zwitterionic naphthalene diimide interlayer. Grazing incidence X-ray diffraction measurements of annealed films reveal that P(NDI2OD-BiTz) adopts a highly ordered edge-on orientation, exactly opposite to similar bithiophene analogs. This report highlights an NDI and thiazole all-acceptor polymer and demonstrates high electron mobility despite its nonplanar backbone conformation.

High-Resolution Vibronic Spectra of Molecules on Molybdenum Disulfide Allow for Rotamer Identification.

Tunneling spectroscopy is an important tool for the chemical identification of single molecules on surfaces. Here, we show that oligothiophene-based large organic molecules which only differ by single bond orientations can be distinguished by their vibronic fingerprint. These molecules were deposited on a monolayer of the transition metal dichalcogenide molybdenum disulfide (MoS2) on top of a Au(111) substrate. MoS2 features an electronic band gap for efficient decoupling of the molecular states. Furthermore, it exhibits a small electron-phonon coupling strength. Both of these material properties allow for the resolution of vibronic states in the range of the limit set by temperature broadening in our scanning tunneling microscope at 4.6 K. Using DFT calculations of the molecule in gas phase provides all details for an accurate simulation of the vibronic spectra of both rotamers.

Enhanced Device Efficiency and Long-Term Stability via Boronic Acid-Based Self-Assembled Monolayer Modification of Indium Tin Oxide in a Planar Perovskite Solar Cell.

Interfacial engineering is essential for the development of highly efficient and stable solar cells through minimizing energetic losses at interfaces. Self-assembled monolayers (SAMs) have been shown as a handle to tune the work function (WF) of indium tin oxide (ITO), improving photovoltaic cell performance and device stability. In this study, we utilize a new class of boronic acid-based fluorine-terminated SAMs to modify ITO surfaces in planar perovskite solar cells. The SAM treatment demonstrates an increase of the WF of ITO, an enhancement of the short-circuit current, and a passivation of trap states at the ITO/[poly(3,4ethylenedioxylenethiophene):poly(styrenesulfonic acid)] interface. Device stability improves upon SAM modification, with efficiency decreasing only 20% after one month. Our work highlights a simple treatment route to achieve hysteresis-free, reproducible, stable, and highly efficient (16%) planar perovskite solar cells.

Gecko-Inspired Biocidal Organic Nanocrystals Initiated from a Pencil-Drawn Graphite Template.

The biocidal properties of gecko skin and cicada wings have inspired the synthesis of synthetic surfaces decorated with high aspect ratio nanostructures that inactivate microorganisms. Here, we investigate the bactericidal activity of oriented zinc phthalocyanine (ZnPc) nanopillars grown using a simple pencil-drawn graphite templating technique. By varying the evaporation time, nanopillars initiated from graphite that was scribbled using a pencil onto silicon substrates were optimized to yield a high inactivation of the Gram-negative bacteria, Escherichia coli. We next adapted the procedure so that analogous nanopillars could be grown from pencil-drawn graphite scribbled onto stainless steel, flexible polyimide foil, and glass substrates. Time-dependent bacterial cytotoxicity studies indicate that the oriented nanopillars grown on all four substrates inactivated up to 97% of the E. coli quickly, in 15 min or less. These results suggest that organic nanostructures, which can be easily grown on a broad range of substrates hold potential as a new class of biocidal surfaces that kill microbes quickly and potentially, without spreading antibiotic-resistance genes.

Correlating Crystal Thickness, Surface Morphology, and Charge Transport in Pristine and Doped Rubrene Single Crystals.

The relationship between charge transport and surface morphology is investigated by utilizing rubrene single crystals of varying thicknesses. In the case of pristine crystals, the surface conductivities decrease exponentially as the crystal thickness increases until ∼4 µm, beyond which the surface conductivity saturates. Investigation of the surface morphology using optical and atomic force microscopy reveals that thicker crystals have a higher number of molecular steps, increasing the overall surface roughness compared with thin crystals. The density of molecular steps as a surface trap is further quantified with the subthreshold slope of rubrene air-gap transistors. This thickness-dependent surface conductivity is rationalized by a shift from in-plane to out-of-plane transport governed by surface roughness. The surface transport is disrupted by roughening of the crystal surface and becomes limited by the slower vertical crystallographic axis on molecular step edges. Separately, we investigate surface-doping of rubrene crystals by using fluoroalkyltrichrolosilane and observe a different mechanism for charge transport which is independent of surface roughness. This work demonstrates that the correlation between crystal thickness, surface morphology, and charge transport must be taken into account when measuring organic single crystals. Considering the fact that these molecular steps are universally observed on organic/inorganic and single/polycrystals, we believe that our findings can be widely applied to improve charge transport understanding.

Phase Transition of Graphene-Templated Vertical Zinc Phthalocyanine Nanopillars.

We report on the graphene-assisted growth, crystallization, and phase transition of zinc phthalocyanine (ZnPc) vertically oriented single crystal nanopillars. Postcrystallization thermal annealing of the nanostructures results in a molecular packing change while maintaining the vertical orientation of the single crystals orthogonal to the underlying substrate. Grazing incidence X-ray diffraction and high-resolution TEM studies characterized this phase transition from a metastable crystal phase to the more stable ß-phase commonly observed in bulk crystals. These vertical arrays of crystalline nanopillars exhibit a high-surface-to-volume ratio, which is advantageous for applications such as gas sensors. We fabricated chemiresistor sensors with ZnPc nanopillars grown on graphene and demonstrated its selectivity for ammonia vapors, and improvement in sensitivity in the ß-phase crystal packing pillars due to their molecular orientation increasing the exposure of the Zn2+ ion to the ammonia analyte. This work highlights the first morphology-retentive phase transition in organic single crystal nanopillars through simple postprocessing thermal annealing. This study opens up the possibility of molecular packing control without large variations in morphology, a necessity for high-performance devices and establishing structure-property relations.

Direct Printing of Graphene Electrodes for High-Performance Organic Inverters.

Scalable fabrication of high-resolution electrodes and interconnects is necessary to enable advanced, high-performance, printed, and flexible electronics. Here, we demonstrate the direct printing of graphene patterns with feature widths from 300 µm to ∼310 nm by liquid-bridge-mediated nanotransfer molding. This solution-based technique enables residue-free printing of graphene patterns on a variety of substrates with surface energies between ∼43 and 73 mN m-1. Using printed graphene source and drain electrodes, high-performance organic field-effect transistors (OFETs) are fabricated with single-crystal rubrene (p-type) and fluorocarbon-substituted dicyanoperylene-3,4:9,10-bis(dicarboximide) (PDIF-CN2) (n-type) semiconductors. Measured mobilities range from 2.1 to 0.2 cm2 V-1 s-1 for rubrene and from 0.6 to 0.1 cm2 V-1 s-1 for PDIF-CN2. Complementary inverter circuits are fabricated from these single-crystal OFETs with gains as high as ∼50. Finally, these high-resolution graphene patterns are compatible with scalable processing, offering compelling opportunities for inexpensive printed electronics with increased performance and integration density.

Polarization-Dependent Photoinduced Bias-Stress Effect in Single-Crystal Organic Field-Effect Transistors.

Photoinduced charge transfer between semiconductors and gate dielectrics can occur in organic field-effect transistors (OFETs) operating under illumination, leading to a pronounced bias-stress effect in devices that are normally stable while operating in the dark. Here, we report an observation of a polarization-dependent photoinduced bias-stress effect in two prototypical single-crystal OFETs, based on rubrene and tetraphenylbis(indolo{1,2-a})quinolin. We find that the decay rate of the source-drain current in these OFETs under illumination is a periodic function of the polarization angle of incident photoexcitation with respect to the crystal axes, with a periodicity of π. The angular positions of maxima and minima of the bias-stress rate match those of the optical absorption coefficient of the corresponding crystals. The analysis of the effect shows that it stems from a charge transfer of "hot" holes, photogenerated in the crystal within a very short thermalization length (≪µm) from the semiconductor-dielectric interface. The observed phenomenon is a type of intrinsic structure-property relationship, revealing how molecular packing affects parameter drift in organic transistors under illumination. We also demonstrate that a photoinduced charge transfer in OFETs can be used for recording rewritable accumulation channels with an optically defined geometry and resolution, which can be used in a number of potential applications.

Dinaphthotetrathiafulvalene Bisimides: A New Member of the Family of π-Extended TTF Stable p-Type Semiconductors.

Air-stable organic semiconductors based on tetrathiafuluvalene (TTF) were developed by synthesising a series of dinaphthotetrathiafulvalene bisimides (DNTTF-Im) using electron-donating TTF, π-extended naphthalene, and electron-withdrawing imide. Electron-spin-resonance spectroscopy and X-ray single-crystal structure analysis of aryl-substituted DNTTF-Im radical cations confirmed that localisation of the spin resides on the electron-donating TTF moiety. The organic field-effect transistor properties derived from the use of highly crystalline n-butyl (C4) and n-hexyl(C6)-substituted DNTTF-Im were assessed. The hole carrier mobility of C6-DNTTF-Im was improved from 3.7×10-3  cm2 V-1 s-1 to 0.30 cm2 V-1 s-1 in ambient conditions. This is attributed to the raise of the substrate temperature from 25 °C to 200 °C during sublimation. The XRD and microscopy analysis suggested that increasing the substrate temperature accelerates the end-on packing resulting in larger grains suitable for hole charge transport parallel to the substrate.

Tunable fluorescence quenching near the graphene-aqueous interface.

With increased interest in graphene-based sensors for biomolecules and other targets, we investigated the impact of ionic strength on the steady-state emissions from fluorescein labels on proteins adsorbing on pristine CVD (chemical vapor deposited)-graphene on a silica support. Using the model system of fluorescein-tagged fibrinogen we demonstrated that, for fluorescein tags on adsorbed fibrinogen, emission intensity was very sensitive to the salt concentration. This behavior was not seen for fluorescein-tagged fibrinogen in solution. We demonstrated that fluorescein "quenching" in this system was a result of fluorescein's pH sensitivity: with changes in salt concentration, near-surface fluorescein experiences either the neutral bulk pH or, with a negatively charged surface, an acidic environment. The findings carry the important implication that the aqueous environment near silica-supported graphene is substantially acidic as a result of near-surface negative charge. This further implies, because of the purity of the graphene in this study and its lack of oxidation, that negative charge arises from ion adsorption and/or from the underlying silica support, which may be hydrated and present dissociated surface silanols. That is, the electrostatic potential from silica beneath the graphene may pass through the graphene, much as van der Waals interactions have been proven to do. Results were semi-quantitatively consistent with calculations that employed a Guoy Chapman model of the interface and the established pKa of the fluorescein. While these findings were obtained with adsorbed proteins, similar fluorescence quenching would be expected for any fluorescein-tagged species in the vicinity of silica-supported graphene. Thus, because of the negative charge at the aqueous graphene interface, ionic strength can be exploited as means of creating a molecular ruler of fluorescein emissions, and the emissions can be assessed within different distances, corresponding to the Debye length, from the graphene interface.

Poly[2,5-bis(3-dodecylthiophen-2-yl)thieno[3,2-b]thiophene] Oligomer Single-Crystal Nanowires from Supercritical Solution and Their Anisotropic Exciton Dynamics.

Supercritical fluids, exhibiting a combination of liquid-like solvation power and gas-like diffusivity, are a relatively unexplored medium for processing and crystallization of oligomer and polymeric semiconductors whose optoelectronic properties critically depend on the microstructure. Here we report oligomer crystallization from the polymer organic semiconductor, poly[2,5-bis(3-dodecylthiophen-2-yl)thieno[3,2-b]thiophene] (PBTTT) in supercritical hexane, yielding needle-like single crystals up to several microns in length. We characterize the crystals' photophysical properties by time- and polarization-resolved photoluminescence (TPRPL) spectroscopy. These techniques reveal two-dimensional interchromophore coupling facilitated by the high degree of π-stacking order within the crystal. Furthermore, the crystals obtained from supercritical fluid were found to be similar photophysically as the crystallites found in solution-cast thin films and distinct from solution-grown crystals that exhibited spectroscopic signatures indicative of different packing geometries.

Homoepitaxy of Crystalline Rubrene Thin Films.

The smooth surface of crystalline rubrene films formed through an abrupt heating process provides a valuable platform to study organic homoepitaxy. By varying growth rate and substrate temperature, we are able to manipulate the onset of a transition from layer-by-layer to island growth modes, while the crystalline thin films maintain a remarkably smooth surface (less than 2.3 nm root-mean-square roughness) even with thick (80 nm) adlayers. We also uncover evidence of point and line defect formation in these films, indicating that homoepitaxy under our conditions is not at equilibrium or strain-free. Point defects that are resolved as screw dislocations can be eliminated under closer-to-equilibrium conditions, whereas we are not able to eliminate the formation of line defects within our experimental constraints at adlayer thicknesses above ∼25 nm. We are, however, able to eliminate these line defects by growing on a bulk single crystal of rubrene, indicating that the line defects are a result of strain built into the thin film template. We utilize electron backscatter diffraction, which is a first for organics, to investigate the origin of these line defects and find that they preferentially occur parallel to the (002) plane, which is in agreement with expectations based on calculated surface energies of various rubrene crystal facets. By combining the benefits of crystallinity, low surface roughness, and thickness-tunability, this system provides an important study of attributes valuable to high-performance organic electronic devices.

Impact of morphology on polaron delocalization in a semicrystalline conjugated polymer.

We investigate the delocalization of holes in the semicrystalline conjugated polymer poly(2,5-bis(3-alkylthiophene-2-yl)thieno[3,2-b]thiophene) (PBTTT) by directly measuring the hyperfine coupling between photogenerated polarons and bound nuclear spins using electron nuclear double resonance spectroscopy. An extrapolation of the corresponding oligomer spectra reveals that charges tend to delocalize over 4.0-4.8 nm with delocalization strongly dependent on molecular order and crystallinity of the PBTTT polymer thin films. Density functional theory calculations of hyperfine couplings confirm that long-range corrected functionals appropriately describe the change in coupling strength with increasing oligomer size and agree well with the experimentally measured polymer limit. Our discussion presents general guidelines illustrating the various pitfalls and opportunities when deducing polaron localization lengths from hyperfine coupling spectra of conjugated polymers.