Intercalation of Ionic Liquids into LDH Structures for Microwave-Accelerated Polymerizations.

Microwave-accelerated ring-opening polymerization (ROP) of cyclic esters catalyzed by ionic liquid (IL) anions, intercalated into layered double hydroxides (LDHs), has been recently described as a fast and environmentally friendly synthetic way to prepare biodegradable polyester/LDH nanocomposites. However, to observe this synergistic catalytic effect between microwaves and IL anions and to achieve a homogeneous structure of the final polymer nanocomposite, the IL anions must be efficiently intercalated inside the LDH structure. Herein, we investigate the effects of various metal compositions of M2+/Al3+ LDHs (M = Mg, Co, and Ca) and different LDH synthetic routes (one-step direct coprecipitation, two-step coprecipitation/anion exchange, and two-step urea/anion exchange) on the intercalation efficiency of trihexyltetradecylphosphonium bis(2,4,4-trimethylpentyl)phosphinate IL. The most effective IL anion intercalation was observed for Ca2+/Al3+ LDH prepared using the two-step method consisting of coprecipitation and subsequent anion exchange. After optimization, this synthetic pathway led to the production of LDHs with intercalated IL anions and a reduced amount of intercalated water (<0.6 wt %). The catalytic ability of thus optimized LDH particles was demonstrated on the microwave-assisted ROP of ε-caprolactone, showing rapid progress of polymerization. Within minutes, the polycaprolactones with an average molecular mass in the range of 20 000-50 000 g/mol containing fully delaminated and exfoliated LDH nanoparticles were obtained.

Insight into the aqueous Laponite® nanodispersions for self-assembled poly(itaconic acid) nanocomposite hydrogels: The effect of multivalent phosphate dispersants.

HYPOTHESIS: We hypothesize, that physical network between Laponite® nanoparticles and high molecular weight polyelectrolyte formed by mixing of Laponite® nanodispersion (containing multivalent phosphate dispersant) and polyelectrolyte solution is strongly influenced by the type and content of dispersant, which forms electric double layer (EDL) closely to the Laponite® edges. Thus, optimum dispersant concentration is necessary to overcome clay-clay interactions (excellent clay delamination), but should not be exceeded, what would result in the EDL compression and weakening of attractions forming clay-polyelectrolyte network. Thus, deeper investigation of Laponite® nanodispersions is highly demanded since it would enable to better design the self-assembled clay-polyelectrolyte hydrogels. EXPERIMENTS: To study clay interparticle interactions in the presence of various multivalent phosphates, complementary methods providing wide nanodispersion characterization have been applied: zeta potential measurement and SAXS technique (electrostatic interactions), oscillatory rheology (nanodispersion physical state) and NMR experiments (ion immobilization degree). FINDINGS: It was found that multivalent phosphates induce and tune strength of clay-polyelectrolyte interactions forming hydrogel network in terms of varying EDL on the Laponite® edges. Moreover, phosphate dispersing efficiency depends on the molecular size, chemical structure, and valence of the anion; its potential as efficient dispersant for hydrogel preparation can be evaluated by estimation of anion charge density.

Effects of Immobilized Ionic Liquid on Properties of Biodegradable Polycaprolactone/LDH Nanocomposites Prepared by In Situ Polymerization and Melt-Blending Techniques.

The high capacity of calcinated layered double hydroxides (LDH) to immobilize various active molecules together with their inherent gas/vapor impermeability make these nanoparticles highly promising to be applied as nanofillers for biodegradable polyester packaging. Herein, trihexyl(tetradecyl)phosphonium decanoate ionic liquid (IL) was immobilized on the surface of calcinated LDH. Thus, the synthesized nanoparticles were used for the preparation of polycaprolactone (PCL)/LDH nanocomposites. Two different methods of nanocomposite preparation were used and compared: microwave-assisted in situ ring opening polymerization (ROP) of ε-caprolactone (εCL) and melt-blending. The in situ ROP of εCL in the presence of LDH nanoparticles with the immobilized IL led to homogenous nanofiller dispersion in the PCL matrix promoting formation of large PCL crystallites, which resulted in the improved mechanical, thermal and gas/water vapor barrier properties of the final nanocomposite. The surface-bonded IL thus acted as nanofiller surfactant, compatibilizer, as well as thermal stabilizer of the PCL/LDH nanocomposites. Contrary to that, the melt-blending caused a partial degradation of the immobilized IL and led to the production of PCL nanocomposites with a heterogenous nanofiller dispersion having inferior mechanical and gas/water vapor barrier properties.

High-Molecular-Weight Polyampholytes Synthesized via Daylight-Induced, Initiator-Free Radical Polymerization of Renewable Itaconic Acid.

Herein, it is reported for the first time that when mixed with choline chloride, itaconic acid (IA), normally a low-reactive vinyl monomer, undergoes initiator-free radical polymerization under normal daylight. Furthermore, the process results in the formation of abnormally high-molecular-weight poly(itaconic acid) derivatives with Mw greater than ≈800 000 g mol-1 . Detailed 1D/2D NMR studies indicate that the polymers have two types of ionizable moieties, that is, anionic carboxylic and cationic choline ester groups in an average molar ratio of 12:1. Potentiometric titration shows polyampholyte behavior of the polymers. Tentative mechanistic studies reveal that the daylight-induced polymerization is initiated by species generated via interactions of near UV light with IA. However, EPR findings show that choline also participates in secondary radical reactions. The obtained polyampholytes are useful bio-based materials for fast and straightforward fabrication of polymer-clay nanocomposite hydrogels with excellent mechanical properties.

Ionic Liquids as Delaminating Agents of Layered Double Hydroxide during In-Situ Synthesis of Poly (Butylene Adipate-co-Terephthalate) Nanocomposites.

Currently, highly demanded biodegradable or bio-sourced plastics exhibit inherent drawbacks due to their limited processability and end-use properties (barrier, mechanical, etc.). To overcome all of these shortcomings, the incorporation of lamellar inorganic particles, such as layered double hydroxides (LDH) seems to be appropriate. However, LDH delamination and homogenous dispersion in a polymer matrix without use of harmful solvents, remains a challenging issue, which explains why LDH-based polymer nanocomposites have not been scaled-up yet. In this work, LDH with intercalated ionic liquid (IL) anions were synthesized by a direct co-precipitation method in the presence of phosphonium IL and subsequently used as functional nanofillers for in-situ preparation of poly (butylene adipate-co-terephthalate) (PBAT) nanocomposites. The intercalated IL-anions promoted LDH swelling in monomers and LDH delamination during the course of in-situ polycondensation, which led to the production of PBAT/LDH nanocomposites with intercalated and exfoliated morphology containing well-dispersed LDH nanoplatelets. The prepared nanocomposite films showed improved water vapor permeability and mechanical properties and slightly increased crystallization degree and therefore can be considered excellent candidates for food packaging applications.