Parameter dependence of depth and lateral resolution of transmission Kikuchi diffraction.

The spatial resolution of transmission Kikuchi diffraction (TKD) depends on experimental parameters such as atomic number, accelerating voltage, sample backtilt and thickness. In this work, the dependence of spatial resolution on these parameters is explored by using bilayered coarse-grained/nanocrystalline samples to determine the depth resolution. Digital image correlation of the Kikuchi patterns across grain boundaries is used to measure the lateral resolution. The depth resolutions of TKD in aluminium, copper and platinum at 30 kV for an untilted sample were 80, 32 and 14 nm respectively. These worsened with increasing sample backtilt and slightly improved with decreasing accelerating voltage. The best physical lateral resolution obtained was 6 nm, at 30 keV in a 41 nm thick aluminium sample with no backtilt. The lateral resolution worsened with increasing sample thickness and backtilt, contrasting with some previous reports. Accelerating voltage and atomic number did not have a significant impact on the measured lateral resolution within the scatter in the data.

Characterization of Carbide Precipitation in Low-Carbon Martensitic Steels Using an Ultrawide Field-of-View 3D Atom Probe.

It is important to understand the carbide distribution around high-energy sites such as dislocations and grain boundaries in martensitic steels as they have a major influence on the alloy performance. The aim of this study is to characterize fine ε carbides precipitated in low-carbon lath martensitic steel using the ultrawide field-of-view (FoV) CAMECA Invizo 6000 atom probe. We demonstrate the advantages of the wide FoV and determine the optimum conditions for analysis, by comparing the results such as the background noise and the C++/C+ charge state ratio (CSR) between voltage-pulsed and laser-pulsed modes. Increasing the laser pulse energy decreased the background noise and the CSR, where 70 pJ laser pulse energy produced a comparable mass-to-charge ratio spectrum to that recorded in voltage-pulsed mode, with the bulk compositions of C, Si, and Mn closest to that measured using voltage-pulsed mode. Increasing laser pulse energies to above 300 pJ decreased the bulk carbon content, with a more diffuse distribution of carbon around the carbides. This paper outlines some of the important experimental considerations when performing quantitative study of carbide precipitation in low-carbon martensitic steels using the Invizo 6000, considerations that can also be applied to other ferrous and non-ferrous alloy systems.

Analysis of Water Ice in Nanoporous Copper Needles Using Cryo Atom Probe Tomography.

The application of atom probe tomography (APT) to frozen liquids is limited by difficulties in specimen preparation. Here, we report on the use of nanoporous Cu needles as a physical framework to hold water ice for investigation using APT. Nanoporous Cu needles are prepared by electropolishing and dealloying Cu-Mn matchstick precursors. Cryogenic scanning electron microscopy and focused ion beam milling reveal a hierarchical, dendritic, highly wettable microstructure. The atom probe mass spectrum is dominated by peaks of Cu+ and H(H2O)n+ up to n ≤ 3, and the reconstructed volume shows the protrusion of a Cu ligament into an ice-filled pore. The continuous Cu ligament network electrically connects the apex to the cryostage, leading to an enhanced electric field at the apex and increased cooling, both of which simplify the mass spectrum compared to previous reports.

Nanoscale Analysis of Frozen Water by Atom Probe Tomography Using Graphene Encapsulation and Cryo-Workflows.

There has been an increasing interest in atom probe tomography (APT) to characterize hydrated and biological materials. A major benefit of APT compared to microscopy techniques more commonly used in biology is its combination of outstanding three-dimensional (3D) spatial resolution and mass sensitivity. APT has already been successfully used to characterize biominerals, revealing key structural information at the atomic scale, however there are many challenges inherent to the analysis of soft hydrated materials. New preparation protocols, often involving specimen preparation and transfer at cryogenic temperature, enable APT analysis of hydrated materials and have the potential to enable 3D atomic scale characterization of biological materials in the near-native hydrated state. In this study, samples of pure water at the tips of tungsten needle specimens were prepared at room temperature by graphene encapsulation. A comparative study was conducted where specimens were transferred at either room temperature or cryo-temperature and analyzed by APT by varying the flight path and pulsing mode. The differences between the analysis workflows are presented along with recommendations for future studies, and the compatibility between graphene coating and cryogenic workflows is demonstrated.

Estimation of the Electric Field in Atom Probe Tomography Experiments Using Charge State Ratios.

Kingham [(1982). The post-ionization of field evaporated ions: A theoretical explanation of multiple charge states. Surf Sci116(2), 273-301] provided equations for the probability of observing higher charge states in atom probe tomography (APT) experiments. These "Kingham curves" have wide application in APT, but cannot be analytically transformed to provide the electric field in terms of the easily measured charge state ratio (CSR). Here we provide a numerical scheme for the calculation of Kingham curves and the variation in electric field with CSR. We find the variation in electric field with CSR is well described by a simple two- or three-parameter equation, and the model is accurate to most elements and charge states. The model is applied to experimental APT data of pure aluminium and a microalloyed steel, demonstrating that the methods described in this work can be easily applied to a variety of APT problems to understand electric field variations.

Heterostructured WOx/W2C Nanocatalyst for Li2S Oxidation in Lithium-Sulfur Batteries with High-Areal-Capacity.

Lithium-sulfur (Li-S) batteries show extraordinary promise as a next-generation battery technology due to their high theoretical energy density and the cost efficiency of sulfur. However, the sluggish reaction kinetics, uncontrolled growth of lithium sulfide (Li2S), and substantial Li2S oxidation barrier cause low sulfur utilization and limited cycle life. Moreover, these drawbacks get exacerbated at high current densities and high sulfur loadings. Here, a heterostructured WOx/W2C nanocatalyst synthesized via ultrafast Joule heating is reported, and the resulting heterointerfaces contribute to enhance electrocatalytic activity for Li2S oxidation, as well as controlled Li2S deposition. The densely distributed nanoparticles provide abundant binding sites for uniform deposition of Li2S. The continuous heterointerfaces favor efficient adsorption and promote charge transfer, thereby reducing the activation barrier for the delithiation of Li2S. These attributes enable Li-S cells to deliver high-rate performance and high areal capacity. This study provides insights into efficient catalyst design for Li2S oxidation under practical cell conditions.

Unveiling the Role of Ge in CZTSSe Solar Cells by Advanced Micro-To-Atom Scale Characterizations.

Kesterite is an earth-abundant energy material with high predicted power conversion efficiency, making it a sustainable and promising option for photovoltaics. However, a large open circuit voltage Voc deficit due to non-radiative recombination at intrinsic defects remains a major hurdle, limiting device performance. Incorporating Ge into the kesterite structure emerges as an effective approach for enhancing performance by manipulating defects and morphology. Herein, how different amounts of Ge affect the kesterite growth pathways through the combination of advanced microscopy characterization techniques are systematically investigated. The results demonstrate the significance of incorporating Ge during the selenization process of the CZTSSe thin film. At high temperature, the Ge incorporation effectively delays the selenization process due to the formation of a ZnSe layer on top of the metal alloys through decomposition of the Cu-Zn alloy and formation of Cu-Sn alloy, subsequently forming of Cu-Sn-Se phase. Such an effect is compounded by more Ge incorporation that further postpones kesterite formation. Furthermore, introducing Ge mitigates detrimental "horizontal" grain boundaries by increasing the grain size on upper layer. The Ge incorporation strategy discussed in this study holds great promise for improving device performance and grain quality in CZTSSe and other polycrystalline chalcogenide solar cells.

Engineering metal-carbide hydrogen traps in steels.

Hydrogen embrittlement reduces the durability of the structural steels required for the hydrogen economy. Understanding how hydrogen interacts with the materials plays a crucial role in managing the embrittlement problems. Theoretical models have indicated that carbon vacancies in metal carbide precipitates are effective hydrogen traps in steels. Increasing the number of carbon vacancies in individual metal carbides is important since the overall hydrogen trapping capacity can be leveraged by introducing abundant metal carbides in steels. To verify this concept, we compare a reference steel containing titanium carbides (TiCs), which lack carbon vacancies, with an experimental steel added with molybdenum (Mo), which form Ti-Mo carbides comprising more carbon vacancies than TiCs. We employ theoretical and experimental techniques to examine the hydrogen trapping behavior of the carbides, demonstrating adding Mo alters the hydrogen trapping mechanism, enabling hydrogen to access carbon vacancy traps within the carbides, leading to an increase in trapping capacity.

Room-temperature super-elongation in high-entropy alloy nanopillars.

Nanoscale small-volume metallic materials typically exhibit high strengths but often suffer from a lack of tensile ductility due to undesirable premature failure. Here, we report unusual room-temperature uniform elongation up to ~110% at a high flow stress of 0.6-1.0 GPa in single-crystalline <110>-oriented CoCrFeNi high-entropy alloy nanopillars with well-defined geometries. By combining high-resolution microscopy and large-scale atomistic simulations, we reveal that this ultrahigh uniform tensile ductility is attributed to spatial and synergistic coordination of deformation twinning and dislocation slip, which effectively promote deformation delocalization and delay necking failure. These joint and/or sequential activations of the underlying displacive deformation mechanisms originate from chemical compositional heterogeneities at the atomic level and resulting wide variations in generalized stacking fault energy and associated dislocation activities. Our work provides mechanistic insights into superplastic deformations of multiple-principal element alloys at the nanoscale and opens routes for designing nanodevices with high mechanical reliability.

Enhancing methane production from anaerobic digestion of secondary sludge through lignosulfonate addition: Feasibility, mechanisms, and implications.

This study explores the feasibility of using lignosulfonate, a byproduct of the pulp and paper industry, to facilitate sludge anaerobic digestion. Biochemical methane potential assays revealed that the maximum methane production was achieved at 60 mg/g volatile solids (VS) lignosulfonate, 22.18 % higher than the control. One substrate model demonstrated that 60 mg/g VS lignosulfonate boosted the hydrolysis rate, biochemical methane potential, and degradation extent of secondary sludge by 19.12 %, 21.87 %, and 21.11 %, respectively, compared to the control. Mechanisms unveiled that lignosulfonate destroyed sludge stability, promoted organic matter release, and enhanced subsequent hydrolysis, acidification, and methanogenesis by up to 31.30 %, 74.42 % and 28.16 %, respectively. Phytotoxicity assays confirmed that lignosulfonate promoted seed germination and root development of lettuce and Chinese cabbage, with seed germination index reaching 170 ± 10 % and 220 ± 22 %, respectively. The findings suggest that lignosulfonate addition offers a sustainable approach to sludge treatment, guiding effective management practices.

Characterising the performance of an ultrawide field-of-view 3D atom probe.

The CAMECA Invizo 6000 atom probe microscope uses ion optics that differ significantly from the local electrode atom probe (LEAP). It uses dual antiparallel deep ultraviolet lasers, a flat counter electrode, and a series of accelerating and decelerating lenses to increase the field-of-view of the specimen without reducing the mass resolving power. In this work we characterise the performance of the Invizo 6000 using three material case studies: a model Al-Mg-Si alloy, a commercially-available Ni-based superalloy, and a Zr alloy, using a combination of air and vacuum-transfer between instruments. The ion optics of the Invizo 6000 significantly increase the field-of-view compared to the same specimen on a LEAP 4000 X Si. We also observe a significant increase in specimen yield, especially for the Zr alloy. These results combine to make the Invizo 6000 well-suited to research projects requiring large analysis volumes, particularly so for traditionally difficult samples such as oxides.

Translational Boundaries as Incipient Ferrielectric Domains in Antiferroelectric PbZrO_{3}.

In the archetypal antiferroelectric PbZrO_{3}, antiparallel electric dipoles cancel each other, resulting in zero spontaneous polarization at the macroscopic level. Yet in actual hysteresis loops, the cancellation is rarely perfect and some remnant polarization is often observed, suggesting the metastability of polar phases in this material. In this work, using aberration-corrected scanning transmission electron microscopy methods on a PbZrO_{3} single crystal, we uncover the coexistence of the common antiferroelectric phase and a ferrielectric phase featuring an electric dipole pattern of ↓↑↓. This dipole arrangement, predicted by Aramberri et al. to be the ground state of PbZrO_{3} at 0 K, appears at room temperature in the form of translational boundaries. The dual nature of the ferrielectric phase, both a distinct phase and a translational boundary structure, places important symmetry constraints on its growth. These are overcome by sideways motion of the boundaries, which aggregate to form arbitrarily wide stripe domains of the polar phase embedded within the antiferroelectric matrix.

Discovering an unknown territory using atom probe tomography: Elemental exchange at the bioceramic scaffold/bone tissue interface.

Here we report the first atom probe study to reveal the atomic-scale composition of in vivo bone formed in a bioceramic scaffold (strontium-hardystonite-gahnite) after 12-month implantation in a large bone defect in sheep tibia. The composition of the newly formed bone tissue differs to that of mature cortical bone tissue, and elements from the degrading bioceramic implant, particularly aluminium (Al), are present in both the newly formed bone and in the original mature cortical bone tissue at the perimeter of the bioceramic implant. Atom probe tomography confirmed that the trace elements are released from the bioceramic and are actively transported into the newly formed bone. NanoSIMS mapping, as a complementary technique, confirmed the distribution of the released ions from the bioceramic into the newly formed bone tissue within the scaffold. This study demonstrated the combined benefits of atom probe and nanoSIMS in assessing nanoscopic chemical composition changes at precise locations within the tissue/biomaterial interface. Such information can assist in understanding the interaction of scaffolds with surrounding tissue, hence permitting further iterative improvements to the design and performance of biomedical implants, and ultimately reducing the risk of complications or failure while increasing the rate of tissue formation. STATEMENT OF SIGNIFICANCE: The repair of critical-sized load-bearing bone defects is a challenge, and precisely engineered bioceramic scaffold implants is an emerging potential treatment strategy. However, we still do not understand the effect of the bioceramic scaffold implants on the composition of newly formed bone in vivo and surrounding existing mature bone. This article reports an innovative route to solve this problem, the combined power of atom probe tomography and nanoSIMS is used to spatially define elemental distributions across bioceramic implant sites. We determine the nanoscopic chemical composition changes at the Sr-HT Gahnite bioceramic/bone tissue interface, and importantly, provide the first report of in vivo bone tissue chemical composition formed in a bioceramic scaffold.

Sub-4 nm mapping of donor-acceptor organic semiconductor nanoparticle composition.

We report, for the first time, sub-4 nm mapping of donor : acceptor nanoparticle composition in eco-friendly colloidal dispersions for organic electronics. Low energy scanning transmission electron microscopy (STEM) energy dispersive X-ray spectroscopy (EDX) mapping has revealed the internal morphology of organic semiconductor donor : acceptor blend nanoparticles at the sub-4 nm level. A unique element was available for utilisation as a fingerprint element to differentiate donor from acceptor material in each blend system. Si was used to map the location of donor polymer PTzBI-Si in PTzBI-Si:N2200 nanoparticles, and S (in addition to N) was used to map donor polymer TQ1 in TQ1:PC71BM nanoparticles. For select material blends, synchrotron-based scanning transmission X-ray microscopy (STXM), was demonstrated to remain as the superior chemical contrast technique for mapping organic donor : acceptor morphology, including for material combinations lacking a unique fingerprint element (e.g. PTQ10:Y6), or systems where the unique element is in a terminal functional group (unsaturated, dangling bonds) and can hence be easily damaged under the electron beam, e.g. F on PTQ10 donor polymer in the PTQ10:IDIC donor : acceptor blend. We provide both qualitative and quantitative compositional mapping of organic semiconductor nanoparticles with STEM EDX, with sub-domains resolved in nanoparticles as small as 30 nm in diameter. The sub-4 nm mapping technology reported here shows great promise for the optimisation of organic semiconductor blends for applications in organic electronics (solar cells and bioelectronics) and photocatalysis, and has further applications in organic core-shell nanomedicines.

Atomic-Scale Characterization of Planar Selective-Area-Grown InAs/InGaAs Nanowires.

Atomic-scale information about the structural and compositional properties of novel semiconductor nanowires is essential to tailoring their properties for specific applications, but characterization at this length scale remains a challenging task. Here, quasi-1D InAs/InGaAs semiconductor nanowire arrays were grown by selective area epitaxy (SAE) using molecular beam epitaxy (MBE), and their subsequent properties were analyzed by a combination of atom probe tomography (APT) and aberration-corrected transmission electron microscopy (TEM). Results revealed the chemical composition of the outermost thin InAs layer, a fine variation in the indium content at the InAs/InGaAs interface, and lightly incorporated element tracing. The results highlight the importance of correlative microscopy approaches in revealing complex nanoscale structures, with TEM being uniquely suited to interrogating the crystallography of InGaAs NWs, whereas APT is capable of three-dimensional (3D) elemental mapping, revealing the subtle compositional variation near the boundary region. This work demonstrates a detailed pathway for the nanoscale structural assessment of novel one-dimensional (1D) nanomaterials.

NiPS3 ultrathin nanosheets as versatile platform advancing highly active photocatalytic H2 production.

High-performance and low-cost photocatalysts play the key role in achieving the large-scale solar hydrogen production. In this work, we report a liquid-exfoliation approach to prepare NiPS3 ultrathin nanosheets as a versatile platform to greatly improve the light-induced hydrogen production on various photocatalysts, including TiO2, CdS, In2ZnS4 and C3N4. The superb visible-light-induced hydrogen production rate (13,600 µmol h-1 g-1) is achieved on NiPS3/CdS hetero-junction with the highest improvement factor (~1,667%) compared with that of pure CdS. This significantly better performance is attributed to the strongly correlated NiPS3/CdS interface assuring efficient electron-hole dissociation/transport, as well as abundant atomic-level edge P/S sites and activated basal S sites on NiPS3 ultrathin nanosheets advancing hydrogen evolution. These findings are revealed by the state-of-art characterizations and theoretical computations. Our work for the first time demonstrates the great potential of metal phosphorous chalcogenide as a general platform to tremendously raise the performance of different photocatalysts.

Giant room temperature compression and bending in ferroelectric oxide pillars.

Plastic deformation in ceramic materials is normally only observed in nanometre-sized samples. However, we have observed high levels of plasticity (>50% plastic strain) and excellent elasticity (6% elastic strain) in perovskite oxide Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3, under compression along <100>pc pillars up to 2.1 µm in diameter. The extent of this deformation is much higher than has previously been reported for ceramic materials, and the sample size at which plasticity is observed is almost an order of magnitude larger. Bending tests also revealed over 8% flexural strain. Plastic deformation occurred by slip along {110} <1[Formula: see text]0 > . Calculations indicate that the resulting strain gradients will give rise to giant flexoelectric polarization. First principles models predict that a high concentration of oxygen vacancies weaken the covalent/ionic bonds, giving rise to the unexpected plasticity. Mechanical testing on oxygen vacancies-rich Mn-doped Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 confirmed this prediction. These findings will facilitate the design of plastic ceramic materials and the development of flexoelectric-based nano-electromechanical systems.

Boosting Oxygen Reduction Activity of Manganese Oxide Through Strain Effect Caused By Ion Insertion.

Transition-metal oxides with a strain effect have attracted immense interest as cathode materials for fuel cells. However, owing to the introduction of heterostructures, substrates, or a large number of defects during the synthesis of strain-bearing catalysts, not only is the structure-activity relationship complicated but also their performance is mediocre. In this study, a mode of strain introduction is reported. Transition-metal ions with different electronegativities are intercalated into the cryptomelane-type manganese oxide octahedral molecular sieves (OMS-2) structure with K ions as the template, resulting in the octahedral structural distortion of MnO6 and producing strains of different degrees. Experimental studies reveal that Ni-OMS-2 with a high compressive strain (4.12%) exhibits superior oxygen reduction performance with a half-wave potential (0.825 V vs RHE) greater than those of other reported manganese-based oxides. This result is related to the increase in the covalence of MnO6 octahedral configuration and shifting down of the eg band center caused by the higher compression strain. This research avoids the introduction of new chemical bonds in the main structure, weakens the effect of eg electron filling number, and emphasizes the pure strain effect. This concept can be extended to other transition-metal-oxide catalysts.

Simultaneous Large Optical and Piezoelectric Effects Induced by Domain Reconfiguration Related to Ferroelectric Phase Transitions.

Electrical switching of ferroelectric domains and subsequent domain wall motion promotes strong piezoelectric activity, however, light scatters at refractive index discontinuities such as those found at domain wall boundaries. Thus, simultaneously achieving large piezoelectric effect and high optical transmissivity is generally deemed infeasible. Here, it is demonstrated that the ferroelectric domains in perovskite Pb(In1/2 Nb1/2 )O3 -Pb(Mg1/3 Nb2/3 )O3 -PbTiO3 domain-engineered crystals can be manipulated by electrical field and mechanical stress to reversibly and repeatably, with small hysteresis, transform the opaque polydomain structure into a highly transparent monodomain state. This control of optical properties can be achieved at very low electric fields (less than 1.5 kV cm-1 ) and is accompanied by a large (>10 000 pm V-1 ) piezoelectric coefficient that is superior to linear state-of-the-art materials by a factor of three or more. The coexistence of tunable optical transmissivity and high piezoelectricity paves the way for a new class of photonic devices.