Optimization of Au:CuO Thin Films by Plasma Surface Modification for High-Resolution LSPR Gas Sensing at Room Temperature.

In this study, thin films composed of gold nanoparticles embedded in a copper oxide matrix (Au:CuO), manifesting Localized Surface Plasmon Resonance (LSPR) behavior, were produced by reactive DC magnetron sputtering and post-deposition in-air annealing. The effect of low-power Ar plasma etching on the surface properties of the plasmonic thin films was studied, envisaging its optimization as gas sensors. Thus, this work pretends to attain the maximum sensing response of the thin film system and to demonstrate its potential as a gas sensor. The results show that as Ar plasma treatment time increases, the host CuO matrix is etched while Au nanoparticles are uncovered, which leads to an enhancement of the sensitivity until a certain limit. Above such a time limit for plasma treatment, the CuO bonds are broken, and oxygen is removed from the film's surface, resulting in a decrease in the gas sensing capabilities. Hence, the importance of the host matrix for the design of the LSPR sensor is also demonstrated. CuO not only provides stability and protection to the Au NPs but also promotes interactions between the thin film's surface and the tested gases, thereby improving the nanocomposite film's sensitivity. The optimized sensor sensitivity was estimated at 849 nm/RIU, which demonstrates that the Au-CuO thin films have the potential to be used as an LSPR platform for gas sensors.

Evaluation of Active LDPE Films for Packaging of Fresh Orange Juice.

Microbial development, enzymatic action, and chemical reactions influence the quality of untreated natural orange juice, compromising its organoleptic characteristics and causing nutritional value loss. Active low-density polyethylene (LDPE) films containing green tea extract (GTE) were previously prepared by a blown film extrusion process. Small bags were prepared from the produced films, which were then filled with fresh orange juice and stored at 4 °C. Ascorbic acid (AA) content, sugar content, browning index, color parameters, pH, total acidity (TA) and microbial stability were evaluated after 3, 7, and 14 days of storage. The packaging containing GTE maintained the microbial load of fresh juice beneath the limit of microbial shelf-life (6 log CFU/mL) for the bacterial growth, with a more prominent effect for LDPE with 3%GTE. Regarding yeasts and molds, only the CO_LDPE_3GTE package maintained the microbial load of fresh juice below the limit for up to 14 days. At 14 days, the lowest levels of AA degradation (32.60 mg/100 mL of juice) and development of brown pigments (browning index = 0.139) were observed for the packages containing 3% of GTE, which had a pH of 3.87 and sugar content of 11.4 g/100 mL of juice at this time. Therefore, active LDPE films containing 3% of GTE increase the shelf-life of fresh juice and can be a promising option for storage of this food product while increasing sustainability.

Iridium(III)porphyrin arrays with tuneable photophysical properties.

The photophysical properties of iridium(III) porphyrins complexes with two different axial ligands (Cl(CO) and bipyridine (bpy)) in solution and in cellulose acetate polymer matrix were investigated. The axial ligands substitution was made aiming to evaluate the photophysical properties and the solubility in different solvents. Therefore, dissimilar from the free porphyrin, non-polar solvents (as toluene) favours the quantum yield of iridium(III)porphyrins and ligands with a more extended π-conjugated compound as bpy results in higher yields. Moreover, despite all the porphyrins reveals a negative solvatochromism, the substitution of Cl(CO) ligand by bpy ligand exhibits similar solubility either on non-polar or polar solvents. The observed photoluminescence (PL) at room temperature appears at NIR region in contrast to the previously reported iridium(III) porphyrins. Comparing with free porphyrin H2TTP, the red/NIR PL spectra of the iridium(III)porphyrins (either in solution and in the polymer matrix) reveals remarkable changes. Particularly, a more significative decrease of the red/NIR intensity ratio was detected for [Ir(ttp)(bpy)2] 2 where the maxima of the NIR emission can be adjusted under suitable excitation wavelength.

Optical and Photovoltaic Properties of Thieno[3,2-b]thiophene-Based Push-Pull Organic Dyes with Different Anchoring Groups for Dye-Sensitized Solar Cells.

The effect of anchoring groups on the optical and electrochemical properties of triphenylamine-thienothiophenes, and on the photovoltaic performance of DSSCs photosensitized with the prepared dyes, was studied using newly synthesized compounds with cyanoacetic acid or rhodanine-3-acetic acid groups. Precursor aldehydes were synthesized through Suzuki cross-coupling, whereas Knoevenagel condensation of these with 2-cyanoacetic acid or rhodanine-3-acetic acid afforded the final push-pull dyes. A comprehensive photophysical study was performed in solution and in the solid state. The femtosecond time-resolved transient absorption spectra for the synthesized dyes were obtained following photoexcitation in solution and for the dyes adsorbed to TiO2 mesoporous films. Information on conformation, electronic structure, and electron distribution was obtained by density functional theory (DFT) and time-dependent DFT calculations. Triphenylamine-thienothiophene functionalized with a cyanoacetic acid anchoring group displayed the highest conversion efficiency (3.68%) as the dye sensitizer in nanocrystalline TiO2 solar cells. Coadsorption studies were performed for this dye with the ruthenium-based N719 dye, and they showed dye power conversion efficiencies enhanced by 20-64%. The best cell performance obtained with the coadsorbed N719 and cyanoacetic dye showed an efficiency of 6.05%.

Fastest non-ionic azo dyes and transfer of their thermal isomerisation kinetics into liquid-crystalline materials.

Push-pull bithienylpyrrole-based azo dyes exhibit thermal isomerisation rates as fast as 1.4 µs in acetonitrile at 298 K becoming, thus, the fastest neutral azo dyes reported so far. These remarkably low relaxation times can be transferred into liquid-crystalline matrices enabling light-triggered oscillations in the optical density of the final material up to 11 kHz under ambient conditions.

Molecular photo-oscillators based on highly accelerated heterocyclic azo dyes in nematic liquid crystals.

Benzothiazole-pyrrole-based azo dyes greatly enhance their thermal isomerisation rate by up to 160 times when they are under the influence of the nematic mean field yielding the LC-based photochromic oscillators with the highest oscillation frequencies reported so far (2.6 kHz at 298 K).

Fluorescence and two-photon absorption of push-pull aryl(bi)thiophenes: structure-property relationships.

Photophysical and TPA properties of series of push-pull aryl(bi)thiophene chromophores bearing electron-donating (D) and electron-withdrawing (A) end-groups of increasing strength are presented. All compounds show an intense intramolecular charge transfer (ICT) absorption band in the visible region. Increasing the D and/or A strength as well as the length of the conjugated path induces bathochromic and hyperchromic shifts of the absorption band as reported for analogous push-pull polyenes. Yet, in contrast with corresponding push-pull polyenes, a significant increase in fluorescence is observed. In particular, chromophores built from a phenyl-bithienyl conjugated path and bearing strong D and A end-groups were found to combine very large one and two-photon brightness as well as strong emission in the red/NIR region. These molecules hold promise as biphotonic fluorescent probes for bioimaging.