An investigation into the effect of surfactants on iron oxide powder suspension formulations for fingermark development.

Iron oxide powder suspension (FePS) is a fingermark development technique that can be used on adhesive and non-porous surfaces, the efficacy of which is known to be influenced by the surfactant used in the formulation. Despite previous work optimising surfactants for use in FePS, there is limited understanding of the interactions between surfactants, powders and fingermark residue which aid the successful development of fingermarks. To better understand the effect of surfactant on development quality produced by FePS, this research assessed a wide range of surfactants of different ionic natures and evaluated their ability to develop fingermarks based on the quality of ridge detail, contrast and background development produced. It was found that surfactants play a critical role in the selective deposition of powder on fingermark residue, as formulations made with only water (no surfactant) produced heavy background deposition. The efficacy of each surfactant depended on the quality parameter considered, and the addition of some surfactants hindered fingermark development. Effective surfactants such as T20, KP and TX100 prevented background development and produced well contrasted developed marks. Poor contrast was produced by LN, SP80/T80 and T80 due to indiscriminate powder deposition either across the entire sample or preventing any powder to deposit on the surface, demonstrating the role surfactants play in allowing powder deposition in this technique. The effectiveness of a surfactant in PS was not directly dependent on its ionic nature, and most surfactants were more effective when diluted from stock concentrations. This research has provided a robust base for future work improving fundamental understanding of FePS, which will greatly aid the efficacy of future optimisation efforts.

A snapshot of injecting drug consumption from the analysis of used syringes within the Medically Supervised Injecting Centre in Sydney, Australia.

INTRODUCTION: The administration of illicit drugs by injection is associated with considerable harm, including an increased risk of overdose. The chemical analysis of used syringes can enhance knowledge on injecting drug consumption beyond traditional data sources (self-report surveys). This additional information may be useful during significant global events like the COVID-19 pandemic. This study aimed to examine a snapshot of the drugs injected at the Medically Supervised Injecting Centre (MSIC) in Sydney, Australia, in 2019-2020. METHODS: Used syringes were collected from MSIC across three periods throughout 2019 and 2020 (February 2019, March-April 2020 and June-September 2020). Drug residues were extracted from used syringes using methanol before detection by gas chromatography-mass spectrometry and ultra-performance liquid chromatography-tandem mass spectrometry. The chemical analysis results were compared to self-report data obtained from MSIC clients. RESULTS: Heroin (46-53%), methamphetamine (24-34%) and pharmaceutical opioids (15-27%) were the most common drug residues detected. The chemically detected drugs had declining coherence with the drugs self-reported by MSIC clients across the time periods examined. DISCUSSION AND CONCLUSIONS: There was no significant change in the drugs injected (heroin, methamphetamine and pharmaceutical opioids) across the three periods collected throughout varying COVID-19 lockdown restrictions. Changes in the frequency of other drugs injected and discrepancies between chemical analysis and self-report were potentially related to regulatory changes, degradation or misinformed sales. Routine chemical analysis of used syringes has provided an alternative information source to promote awareness of current drug trends and aid harm reduction.

Organic impurity profiling of 3,4-methylenedioxyamphetamine (MDA) synthesised from helional.

The organic impurity profile of 3,4-methylenedioxyamphetamine (MDA) synthesised from helional via the "twodogs" method was examined to identify route-specific and condition-specific impurities. The synthesis used a condensation reaction, followed by a Beckmann rearrangement, then Hofmann rearrangement, and then conversion to a hydrochloride salt. Two chlorinating agents were investigated for the Hofmann rearrangement reaction, trichloroisocyanuric acid (TCCA) and sodium hypochlorite. Three route-specific impurities were identified in MDA using TCCA, and two of these impurities were condition-specific such that the impurities that formed were dependent on the alcohol used as solvent. Three additional impurities were identified as non-route-specific as they have previously been identified in MDA synthesised from 3,4-methylenedioxycinnamic acid or piperonal. These non-route-specific impurities were also identified in MDA synthesised using sodium hypochlorite. No impurities were detected in MDA hydrochloride. This study identified route- and condition-specific organic impurities in MDA synthesised via the "twodogs" synthetic route using helional as starting material. The results in this study provide further understanding into the illicit synthesis of MDA and highlight the expanding nature of precursors used for illicit drug manufacture. It provides valuable information to decision makers to enact legislative measures and restrict precursors of concern.

Fingermark quality assessment, a transversal study of subjective quality scales.

Fingermark detection research aims to improve the quantity and quality of fingermarks detected through the development of novel techniques. Subsequently, there is a need to evaluate these methods to determine the quality of the developed mark. Since the 1980's there has been a significant number of publications, which utilise a variety of different quality assessment methods. The introduction of common practice methods from the International Fingerprint Research Group (IFRG) aimed to implement a more standardised approach. Although these schemes are recommended as common practice, they are only guidelines. Consequentially, there is currently no universally accepted method to evaluate the enhancement techniques implemented in research. Therefore, this study aimed to collate and analyse the published protocols being used within fingermark detection research in order to better understand their application and how research is currently analysing and interpreting fingermark quality. This study comprised of manual and automatic searches of over 2000 published papers within the fingermark detection area. After thorough analysis of the articles, 396 published papers were found to have used a scale within the years spanning 1998-2022. The number of publications that report the use of a scale to assess quality for fingermark detection research has considerably increased over the last decade. However, whilst the number of publications utilising scales has increased, it is not proportional to the number of papers using the IFRG scales. The choice of scale is often institution specific and even more specific to their location. There are also numerous different adaptations of the IFRG recommended scales, as well as novel scales, which do not associate with the IFRG recommended versions being introduced the more research continues to grow. One such reason for this is investigated here, as different quality parameters are utilised within each individual scale. There is underrepresentation of these quality parameters within some of the IFRG scales, in particular the Centre for Applied Science and Technology (CAST) scale. This correlates to the considerable number of tailored approaches as authors are forced to add these parameters within the descriptions. Until there is an introduction of clear guidelines surrounding all areas of fingermark quality, from definition to parameters chosen within phases, the research area will continue to face such issues. This article recommends areas of potential study, whilst also recommending procedures that may be employed to alleviate some of the issues seen with fingermark quality evaluation.

Comparison of carbon and iron oxide based powder suspension formulations.

Powder suspensions (PS) are a fingermark development technique made up of a mixture of an insoluble powder and surfactant solution. In the UK, carbon-based PS is used operationally on adhesive surfaces while iron oxide-based PS is used on flexible plastics. In NSW, Australia, only carbon-based suspensions are used due to a lack of research using iron oxide PS in an Australian context. In this research, a range of iron oxide powders and surfactant types were tested to optimise two iron oxide formulations. General observations found that thinner suspensions improved the ease of use in this technique while slightly improving the quality of developed fingermarks. The first optimised formulation involved a magnetic iron-oxide from Fisher Scientific mixed with a dilute Triton X-100 surfactant, and the other an iron-oxide nanopowder from Sigma Aldrich mixed with a 4% Tween 20 solution. The two formulations were then compared with a pre-mixed carbon-based PS, Wet Powder. This comparison showed that the effectiveness of each formulation is heavily dependent on substrate type. Both formulations had issues with heavy background staining on different kinds of surfaces. However, Wet Powder was shown to be the most consistently effective fingermark detection technique overall, especially on adhesive tapes. Despite this, iron-oxide PS were still a highly effective fingermark development technique, notably on plastic surfaces.

Biodegradable plastics and their impact on fingermark detection methods.

The use of plastics is extremely prevalent in society, with most individuals likely to handle several plastic items per day. It is therefore not surprising that many exhibits recovered from the scene of a crime are plastics, which are processed and examined for traces such as fingermarks. Societal trends have been pushing towards more environmentally friendly products with alternatives to traditional disposable plastics becoming increasingly available. These alternate plastics have different chemical compositions and physical properties, which may impact fingermark development for these substrates. As most detection techniques are known to be substrate-dependent, it is crucial to review current methods and procedures to examine how effective they are on new materials. The aim of this research was to assess a range of fingermark detection techniques on biodegradable plastics and provide recommendations for the preferred technique. First, the prevalence of these materials in the Australian market was evaluated. Over 40 different plastics obtained within the Sydney area were then divided into six broad categories using consumer information in combination with ATR-FTIR spectroscopy analysis. Following this, selected plastics from each category were used as substrates for the fingermark development study. In total, 6480 fingermark specimens were collected as split marks, to form 2160 fingermark comparisons. Each substrate was then developed with four fingermark detection techniques suitable for plastic substrates: cyanoacrylate (CA) fuming, vacuum metal deposition (VMD), powder suspensions (PS), and single metal deposition (SMD). SMD resulted in the most consistent development method across all tested substrates. VMD was able to successfully develop fingermarks on polyethylene-based plastics, but led to poorer results on alternative plastics, while CA fuming and PS were notably more dependent on the surface texture. This research was successful in confirming that biodegradable plastics do in fact have an impact on fingermark development techniques commonly applied on traditional plastics and recommendations have been formed to aid in operational contexts to improve the potential to recover latent fingermarks from biodegradable plastics.

Comparison of NIR powders to conventional fingerprint powders.

Fingerprint powders remain one of the most common detection techniques used at the crime scene. However, powder efficiency and contrast can be hindered when applied to highly patterned backgrounds. This problem can be overcome using powders that are luminescent in the near-infrared (NIR) region of the electromagnetic spectrum. Despite being commercially available, those powders have been the focus of only a small number of studies, limited to a few substrates or donors. Their performance and advantages over common techniques are still to be thoroughly investigated. This study aims at assessing the performances of two NIR powder (fpNATURAL 1® and Universal Powder an in-house developed powder) against two conventional powders, a black and a luminescent powder (Sirchie Black, GREENcharge™) under various optical conditions (white light, visible luminescence and NIR luminescence). The powders were compared on four substrates using fingermarks of four different ages from five donors. A total 900 fingermarks were collected for each pairwise comparison. NIR imaging provided good background suppression and a high contrast, however it was shown that conventional powders remained the most effective powdering methods on the substrates tested as sufficient contrast could be achieved under white light or in luminescent mode in the visible region. The results showed that Universal Powder performed similarly to conventional powders, but poor performances were obtained on most substrates with fpNATURAL 1®. Based on the results obtained, it is recommended to use NIR powders only on substrates or conditions where traditional powders are known to perform poorly.

Evaluating the effect of barrel length on pellet distribution patterns of sawn-off shotguns.

In recent years, sawn-off shotguns have been regularly encountered in firearm-related incidents. Shotgun represents a community threat due to their ability to be shortened in order to improve their concealability. In practice, forensic scientists and investigators may be asked to determine if a shotgun used in a particular event might have been shortened based on the pellet distribution. To investigate the effect of altering the barrel length on pellet distribution, five 12-gauge shotguns were progressively shortened. Each shotgun was assessed at six barrel lengths and a single discharge of No. 4 shot shotshell ammunition was fired at a fixed fabric target. The shotguns were positioned at six different distances from target and experiments conducted in triplicate. The fabric targets containing pellet pattern underwent data analysis to calculate the pellet distribution area. At short distances from target (≤ 1.0 m), the pellet penetration was observed as a single entry point as the pellets did not have a sufficient flight time to spread from each other. For distances of 2.5 m, 5 m and 10 m, pellet penetration patterns were observed and a quantitative analysis was performed on the samples containing pellet distribution patterns. At each of these distances, it was detected that there was a noticeable increase in pellet distribution area between the unaltered shotgun and altered barrel lengths for all shotguns. The distance from the target as well as the presence of a choke in the shotgun's barrel was found to have a greater impact on the pellet distribution than the barrel length.

Investigation into the effect of fingermark detection chemicals on the analysis and comparison of pressure-sensitive tapes.

Pressure sensitive tapes such as duct tape are a common trace type sent for forensic analysis. The limited variation of tape backings and adhesives can provide valuable linkage evidence between a scene, a victim or a person of interest. Fingermarks are also often found on tapes and prioritised over tape analyses. This project aimed to investigate the effects of fingermark enhancement chemicals, namely Wet Powder™, cyanoacrylate and cyanoacrylate stained with rhodamine 6G, on various tapes and their comparison with untreated tapes. The changes in physical and optical features were observed using a Video Spectral Comparator (VSC) and microscopy. Chemical changes were analysed by Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy (ATR-FTIR). Most physical and optical properties were not heavily affected by the treatments. An increase in fluorescence was observed with specimens stained with rhodamine 6G as might be expected. Significant chemical changes were observed in the FTIR spectra produced from cyanoacrylate fuming. Polyethylene backings and rubber adhesives were heavily affected while polypropylene backings were moderately affected. Cellulose backings, polyester and polyacrylate adhesives were not significantly affected. Wet Powder™ treatment proved useful for enhancing fingermarks on most adhesives while leaving behind little chemical residue that might interfere in a forensic comparison.

An investigation on the secondary transfer of organic gunshot residues.

Gunshot residues (GSR) are an important forensic trace in firearm-related events. Currently, routine GSR analyses focus on the detection and characterisation of the inorganic components (IGSR). The increasing prevalence of heavy metal-free ammunition challenges these current protocols and there is an increasing interest in how the organic components of GSR (OGSR) can provide complementary information. Similar to the situation with IGSR, OGSR compounds originally deposited on the shooter during the firing process may further be transferred onto another individual or surface. Hence, the aim of this study was to provide additional information regarding the risk of a secondary transfer of OGSR. Two scenarios were investigated, the first one related to the arrest process and the possibilities of a secondary transfer arising between a shooter onto a non-shooter (e.g. between a police officer and a person of interest (POI)). The second scenario concerned the transfer of OGSR onto the non-shooter after handling a firearm for few minutes without discharging it. One calibre was chosen, the .40 S&W calibre, used by several Australian State police forces. A secondary transfer was observed in all cases for the two scenarios investigated, for three compounds of interest: ethylcentralite (EC), diphenylamine (DPA), N-nitrosodiphenylamine (N-nDPA). The firearm handling scenario resulted in a larger secondary transfer to that of the arrest scenario. Overall, the amounts of OGSR detected on the non-shooter were generally lower than that detected on the shooter and controls after the arrest scenario. The results of this study provide complementary knowledge about OGSR, which can be further used to improve the current practice and the interpretation of OGSR evidence. In particular, it highlights that the secondary transfer proposition must be considered during the interpretation of forensic findings, especially when small amounts of OGSR target compounds are detected.

Investigation of some of the factors influencing fingermark detection.

The primary aims of fingermark detection research are to improve the quality and increase the rate of detection of identifiable impressions. This is usually performed through the development of new methods and technologies to provide alternatives to or improve current procedures. While research of this nature is important to pursue, it fails to address the underlying question related to the factors that affect the detection of a latent fingermark. There has been significant research that has examined the differences between techniques, donors and fingermark age, as well as the composition of latent fingermarks. However, they tend not to focus on determining how these factors influence the quality of the developed mark. This study involved the development and evaluation of over 14,000 natural fingermarks deposited on a variety of surfaces to examine the effect of substrate, age, donor variability (both inter- and intra-), depletions and type of finger on fingermark development. Fingermarks were deposited on four substrates (two non-porous and two porous) and developed with either indanedione-zinc (IND-Zn) or cyanoacrylate followed by rhodamine 6G staining (CA+R6G). Three independent assessors graded each mark on the quality of development using an absolute scale proposed by the UK Centre for Applied Science and Technology (CAST). The data generated from these assessments were then analysed for trends or other useful insights. The results from this work reaffirm that individual substrate characteristics (and the choice of development technique) play a significant role in determining the number and quality of marks developed. It was found that fingermarks were more likely to be detected on porous substrates and to also be of a higher quality than on non-porous. The effect of fingermark donor variability was also explored, with significant differences observed between donors and within donors. This research shows that current detection techniques do not detect all available fingermarks, reinforcing the need for further research into the fundamentals of fingermark detection in order to gain a better understanding of the techniques currently used. The study has identified considerations for the development of novel techniques and how we need to account for variability when designing fingermark research experiments.

Impact of one-step luminescent cyanoacrylate treatment on subsequent DNA analysis.

Fingermarks can be exploited for both their ridge detail and touch DNA. One-step luminescent cyanoacrylate (CA) fuming techniques used for fingermark enhancement, such as PolyCyano UV (Foster+Freeman Ltd) and Lumicyano™ (Crime Science Technology), claim to be compatible with DNA analysis as they reduce the need for post-staining to increase contrast of the developed fingermark. The aim of this study was to determine the impact that these one-step luminescent cyanoacrylates have on DNA analysis and how they compare to conventional CA techniques. Four donors each deposited five sets of natural fingermarks, to which a known amount of washed saliva cells was dispensed onto half of each set of fingermarks. Each set was treated with either a conventional CA technique or a one-step luminescent CA technique prior to collection and processing of DNA, with one set left as a non-fumed control. It was found that DNA was still recoverable and detectable following each of the treatments. Lumicyano™ had a similar impact on DNA profiles as conventional CA fuming and with post-stain, however, the degradation effect of PolyCyano UV on DNA was greater than the conventional treatments. For quantities of DNA such as that from touch DNA, the use of PolyCyano UV to enhance fingermarks may impact subsequent DNA analysis by causing allele drop out at larger fragment sizes.

Dataset of coded handwriting features for use in statistical modelling.

The data presented here is related to the article titled, "Using handwriting to infer a writer's country of origin for forensic intelligence purposes" (Agius et al., 2017) [1]. This article reports original writer, spatial and construction characteristic data for thirty-seven English Australian writers and thirty-seven Vietnamese writers. All of these characteristics were coded and recorded in Microsoft Excel 2013 (version 15.31). The construction characteristics coded were only extracted from seven characters, which were: 'g', 'h', 'th', 'M', '0', '7' and '9'. The coded format of the writer, spatial and construction characteristics is made available in this Data in Brief in order to allow others to perform statistical analyses and modelling to investigate whether there is a relationship between the handwriting features and the nationality of the writer, and whether the two nationalities can be differentiated. Furthermore, to employ mathematical techniques that are capable of characterising the extracted features from each participant.

Using handwriting to infer a writer's country of origin for forensic intelligence purposes.

Forensic science has traditionally focused the majority of its resources and objectives towards addressing Court-related questions. However, this view restricts the contribution of forensic science to one process and results in a loss of information as the investigative and intelligence roles are largely neglected. A forensic science discipline suffering from this imbalance is handwriting examination, which may be characterised as a time consuming and subjective process that is mostly carried out towards the end of the investigation for the purpose of judicial proceedings. Individual and habitual characteristics are the major handwriting features exploited, however alternate information concerning the author's native language could potentially be used as a key element in an intelligence framework. This research focussed on the detection of characteristics that differentiate Vietnamese and English Australian writers based on their English handwriting. The study began with the extraction of handwriting characteristics from the writing of people from the two populations. The data was analysed using a logistic regression model and a classification and regression tree (CRT). Each recognised four class characteristics that were capable of distinguishing between the two nationalities. The logistic regression and CRT models were both capable of correctly predicting 93% of cases. Their predictive capabilities were then tested and supported using blind exemplars in order to mirror casework settings. It appeared that when using their respective class characteristics, the two models were capable of differentiating English Australians from Vietnamese in the data set. This proof of concept research demonstrated the plausibility of exploiting this additional information from a handwriting trace and taking advantage of it in an intelligence-led framework.

The use of handwriting examinations beyond the traditional court purpose.

Traditionally, forensic science has predominantly focused its resources and objectives on addressing court related questions. However, this view restricts the contribution of forensic science to one function and results in lost opportunities as investigative and intelligence roles are often overlooked. A change of perspective and expansion of the contributions of forensic science is required to take advantage of the benefits of abductive and inductive thought processes throughout the investigative and intelligence functions. One forensic discipline that has the potential to broaden its traditional focus is handwriting examination. Typically used in investigations that are focused on both criminal and civil cases, the examination procedure and outcome are time consuming and subjective, requiring a detailed study of the features of the handwriting in question. Traditionally, the major handwriting features exploited are characteristics that are often considered individual (or at least highly polymorphic) and habitual. However, handwriting can be considered as an information vector in an intelligence framework. One such example is the recognition of key elements related to the author's native language. This paper discusses the traditional method generally used around the world and proposes a theoretical approach to expand the application of handwriting examination towards gaining additional information for intelligence purposes. This concept will be designed and tested in a future research project.

Effect of hand sanitizer on the performance of fingermark detection techniques.

Hand sanitizers have seen a rapid increase in popularity amongst the general population and this increased use has led to the belief that hand sanitizers may have an effect on subsequent fingermark detection. Based on this hypothesis, three alcoholic and two non-alcoholic hand sanitizers were evaluated to determine the effect they had on the detection of fingermarks deposited after their use. The following fingermark detection methods were applied: 1,2-indanedione-zinc, ninhydrin, physical developer (porous substrate); and cyanoacrylate, rhodamine 6G, magnetic powder (non-porous substrate). Comparison between hand sanitized fingermarks and non-hand sanitized fingermarks showed that the alcohol-based hand sanitizers did not result in any visible differences in fingermark quality. The non-alcoholic hand sanitizers, however, improved the quality of fingermarks developed with 1,2-indanedione-zinc and ninhydrin, and marginally improved those developed with magnetic powder. Different parameters, including time since hand sanitizer application prior to fingermark deposition and age of deposited mark, were tested to determine the longevity of increased development quality. The non-alcoholic hand sanitized marks showed no decrease in quality when aged for up to two weeks. The time since sanitizer application was determined to be an important factor that affected the quality of non-alcoholic hand sanitized fingermarks. It was hypothesized that the active ingredient in non-alcoholic hand sanitizers, benzalkonium chloride, is responsible for the increase in fingermark development quality observed with amino acid reagents, while the increased moisture content present on the ridges resulted in better powdered fingermarks.

Evaluation of one-step luminescent cyanoacrylate fuming.

One-step luminescent cyanoacrylates have recently been introduced as an alternative to the conventional cyanoacrylate fuming methods. These new techniques do not require the application of a luminescent post-treatment in order to enhance cyanoacrylate-developed fingermarks. In this study, three one-step polymer cyanoacrylates: CN Yellow Crystals (Aneval Inc.), PolyCyano UV (Foster+Freeman Ltd.) and PECA Multiband (BVDA), and one monomer cyanoacrylate: Lumikit™ (Crime Scene Technology), were evaluated against a conventional two-step cyanoacrylate fuming method (Cyanobloom (Foster+Freeman Ltd.) with rhodamine 6G stain). The manufacturers' recommended conditions or conditions compatible with the MVC™ 1000/D (Foster+Freeman Ltd.) were assessed with fingermarks aged for up to 8 weeks on non-porous and semi-porous substrates. Under white light, Cyanobloom generally gave better development than the one-step treatments across the substrates. Similarly when viewed under the respective luminescent conditions, Cyanobloom with rhodamine 6G stain resulted in improved contrast against the one-step treatments except on polystyrene, where PolyCyano UV and PECA Multiband gave better visualisation. Rhodamine 6G post-treatment of one-step samples did not significantly enhance the contrast of any of the one-step treatments against Cyanobloom/rhodamine 6G-treated samples.

Understanding Physical Developer (PD): Part II--Is PD targeting eccrine constituents?

Physical developer (PD) is a fingermark development technique that deposits silver onto fingermark ridges. It is the only technique currently in routine operational use that gives results on porous substrates that have been wet. There is a reasonable understanding of the working solution chemistry, but the chemical constituent(s) contained in fingermark residue that are specifically targeted by PD are largely unknown. A better understanding of the PD technique will permit a more informed selection of alternative or complementary detection methods, and greater usage in operational laboratories. Recent research by our group has shown that PD does not selectively target the lipids present in the residue. This research investigated the hypothesis that PD targets the eccrine constituents in fingermark residue. This was tested by comparison of PD and indanedione-zinc (Ind-Zn) treated natural fingermarks that had been deposited successively, and marks that had been deposited with a ten second interval in between depositions. Such an interval allows for the regeneration of secretions from the pores located on the ridges of the fingers. On fingermark depletions with no time interval between depositions, PD and Ind-Zn treated depletions successively (and comparatively) decreased in development intensity as the amount of residue diminished. Short time intervals in between successive depletions resulted in additional secretions from the pores intermittently occurring, the increased development of which was visualised by treatment with both PD and Ind-Zn. The changes in development intensity were seen with both techniques on the same split depletions in a series, comparably and proportionately. These results indicate that the components targeted by PD are contained in the material excreted by the friction ridge pores through its mirrored development with Ind-Zn. Repetition of the experiments on marks that only contained eccrine material showed good Ind-Zn development but poor results with PD. This indicates that there are other constituents contained in "natural" fingermarks that are required to be present for PD to be able to target constituents in the eccrine sweat. It may be that the required constituents in the natural residues are non-water soluble, and that these protect the eccrine constituents from solubilisation in the aqueous washes employed in the PD method. Further research is being undertaken to determine whether PD is targeting specific compounds in the pore secretions, or a mixture of compounds consisting of the eccrine material, epidermal lipids and sebaceous lipids typically present in latent fingermark residues.

Understanding physical developer (PD): Part I--Is PD targeting lipids?

Physical developer (PD) is a fingermark development technique that involves the selective reduction of silver onto fingermark residue. PD can develop marks on porous substrates even if they have been wet, leading to the logical, long held belief that the reagent targets the water insoluble constituents in the fingermark residue. The present research has tested this hypothesis as part of a broader study that aims to identify the targets of physical developer. Spot tests of some fatty acids, cholesterol and squalene, treated with PD, showed that only cholesterol produced significant silver deposition. PD is known to be particularly effective on aged marks, however cholesterol degrades over time. These observations indicate that PD reactivity with fingermarks cannot solely be due to the presence of cholesterol. Fingermarks were deposited on paper and washed with various organic solvents before being treated with PD. PD effectiveness was intermittent on both solvent washed and unwashed sides of both natural and groomed marks; however, it was seen to effectively develop groomed samples that had been exposed to common lipid extraction solvents, shown to have removed the lipids by visualisation using the lipid stain Nile red. PD effectiveness was most affected by exposure of samples to solvents that could dissolve water soluble components, showing that the removal of these constituents (by either water, or other solvents) decreases the amount of silver deposited on the fingermark residue by the working solution. Close observation of PD developed samples showed variation in silver deposition uniformity when comparing a developed ridge to a pore site located on that ridge. Some samples showed an absence of silver, and other showed an increase of silver at pore locations. This indicates that the material excreted by the pores on the finger has an effect on silver deposition, suggesting that PD may be specifically targeting eccrine constituents that are present along the ridges but are more concentrated at the pore locations. These findings indicate that PD is not targeting the lipids in the fingermark residue per se, and may instead be targeting eccrine constituents or a more complex mixture of both eccrine and lipid constituents. Further investigation is underway within our group to investigate the components targeted by PD to gain a better understanding of what is a notoriously sensitive and hard to employ technique in the hope that it can be improved or simplified, or alternatives identified.