RESUMO
OBJECTIVES: This study aimed to compare the effects of virtual adjustment on occlusal interferences in mandibular posterior single crown and three-unit bridge restorations by using the mandibular movement track and the movement parameters of a virtual articulator. METHODS: Twenty-two participants were recruited. Digital casts of the maxillary and mandibular arches were obtained using an intraoral scanner, and the jaw registration system was used to record the data of the mandibular movement track and the movement parameters of the articulator. Four kinds of restorations with 0.3 mm occlusal interferences were designed with dental design software. In particular, single crowns were designed for teeth 44 and 46, whereas three-unit bridges were designed for teeth 44-46 and 45-47, and the corresponding natural teeth were virtually extracted. Virtual adjustment of the restorations was performed using two dynamic occlusal recordings, namely, the mandibular movement track and the movement parameters of the virtual articulator. A reverse-engineering software was used to measure the root-mean-square of the three-dimensional deviation of the occlusal surfaces between natural teeth and the adjusted restorations. The differences between the two methods of virtual-occlusion adjustment were compared and analyzed. RESULTS: For the same group of restorations, the three-dimensional deviation of the mandibular movement track group were lower than those of the virtual articulator group, and the differences were statistically significant (P<0.05). For the four groups of restorations adjusted by the same method, the three-dimensional deviation of the 46-tooth single crown was the largest and the smallest three-dimensional deviation was that of the 44-tooth single crown. Statistical differences existed between the 44-tooth single crown and the other groups (P<0.05). CONCLUSIONS: For the occlusal design of posterior single crown and three-unit bridge, the mandibular movement track could be a more effective approach to virtual occlusal adjustment than the movement parameters of the virtual articulator.
Assuntos
Articuladores Dentários , Ajuste Oclusal , Humanos , Boca Edêntula , Registro da Relação Maxilomandibular , SoftwareRESUMO
PURPOSE: To compare the sagittal condylar inclination (SCI) in dentate individuals measured by the different methods with mechanical articulator (MA), virtual articulator (VA), and a jaw tracking device (JTD) system. MATERIALS AND METHODS: A total of 22 healthy dentate participants were enrolled in this study. For MA workflow, the SCI was obtained by a semi-adjustable articulator with protrusive interocclusal records. The SCI was also set on a VA by aligning intraoral scan (IOS) with cone beam computed tomography (CBCT) and facial scan (FS), respectively. These virtual workflows were conducted in a dental design software, namely VAIOS-CBCT and VAIOS-FS. Meanwhile, a JTD system was also utilized to perform the measurement. Intraclass correlation was used to assess the repeatability within workflows. The bilateral SCI values were compared by Wilcoxon matched-pairs signed rank test for each workflow, and Kruskal-Wallis test and post hoc p-value Bonferroni correction were used to compare the differences among four workflows. The agreement of VAIOS-CBCT, VAIOS-FS, and JTD compared with MA was evaluated by Bland-Altman analysis. RESULTS: Intraclass correlation of the SCI revealed a high degree of repeatability for each workflow. There were no significant differences between the left and right sides (P > .05), except for VAIOS-CBCT (P = .028). Significant differences were not found between MA and VAIOS-FS (P > .05). Bland-Altman plots indicated VAIOS-CBCT, VAIOS-FS, and JTD were considered to substitute MA with high 95% limits of agreement. CONCLUSION: The workflow of VAIOS-FS provided an alternative approach to measure the SCI compared with MA.
RESUMO
PURPOSE: The purpose of this in vitro study was to assess whether scanning strategies of virtual interocclusal record (VIR) affect the accuracy of VIR during intraoral scanning. MATERIALS AND METHODS: Five pairs of reference cubes were added to the digital upper and lower dentitions of a volunteer, which were printed into resin casts. Subsequently, the resin casts were articulated in the maximal intercuspal position in a mechanical articulator and scanned with an industrial computed tomography system, of which the VIR was served as a reference VIR. The investigated VIR of the upper and lower jaws of the resin master cast were recorded with an intraoral scanner according to 9 designed scanning strategies. Then, the deviation between the investigated VIRs and reference VIR were analyzed, which were measured by the deviation of the distances of six selected reference points on the upper reference cubes in each digital cast to the XY-plane between the investigated VIRs and reference VIR. RESULTS: For the deviation in the right posterior dentitions, RP group (only scanning of right posterior dentitions) showed the smallest deviation. Besides, BP group (scanning of bilateral posterior dentitions) showed the smallest deviation in the left posterior dentitions. Moreover, LP group (scanning of left posterior dentitions) showed the smallest deviation in the anterior dentitions. For the deviation of full dental arches, BP group showed the smallest deviation. CONCLUSION: Different scanning strategies of VIR can influence the accuracy of alignment of virtual dental casts. Appropriate scanning strategies of VIR should be selected for different regions of interest and edentulous situations.
RESUMO
OBJECTIVE: To evaluate the influence of crown coverage of surgical guides on the accuracy of static computer-assisted implant surgeries (sCAISs) in different partially edentulous situations. METHODS: Acrylic models with five types of partially edentulous situations were fabricated in this study. In coDiagnostiX software (Dental Wings, Montreal, Canada), surgical templates were designed and fabricated with reduced crown coverage (RCC), standard crown coverage (SCC) and extended crown coverage (ECC). Then, fully guided implant placement into the acrylic models was performed by dental surgeons with more than 10 years of experience. In total, 120 models and 120 guides were manufactured, and 168 bone-level Straumann replica implants (4.1 × 10 mm, Institut Straumann AG, Basel, Switzerland) were inserted. Postoperative implant positions were scanned (Trios 3, 3 shape, Copenhagen, Denmark) and compared with the preplanned virtual positions via coDiagnostiX (Dental Wings, Montreal, Canada). The angular, coronal and apical deviations were measured and analyzed to evaluate the accuracy of implant insertion. Statistical analysis was performed using one-way ANOVA and Tukey's test. RESULTS: For single tooth missing situations, the RCC group was similar to the SCC group and ECC group in anterior sites. In premolar or molar sites, the SCC and ECC groups had no statistically significant difference (p > .05), while the RCC group had more coronal and apical deviation (p < .05). For multiple teeth missing situations, there was no difference among the RCC, SCC and ECC groups (p > .05). No difference was found among the five edentulous situations with different CCs (p > .05). CONCLUSION: The CC of templates can significantly affect the accuracy of guided surgeries when implants are inserted in a single gap at posterior sites. Templates with CC extended to the undercut line may be an optimal choice for static guided surgeries. CLINICAL SIGNIFICANCE: The accuracy of static guided implant surgery can be influenced by the CC of templates, and proper CC with the guide covering extending to the undercut line may contribute to improved accuracy. CC should be taken into consideration when designing surgical templates.