Broadband Fourier-transform silicon nitride spectrometer with wide-area multiaperture input.

Integrated microspectrometers implemented in silicon photonic chips have gathered a great interest for diverse applications such as biological analysis, environmental monitoring, and remote sensing. These applications often demand high spectral resolution, broad operational bandwidth, and large optical throughput. Spatial heterodyne Fourier-transform (SHFT) spectrometers have been proposed to overcome the limited optical throughput of dispersive and speckle-based on-chip spectrometers. However, state-of-the-art SHFT spectrometers in near-infrared achieve large optical throughput only within a narrow operational bandwidth. Here we demonstrate for the first time, to the best of our knowledge, a broadband silicon nitride SHFT spectrometer with the largest light collecting multiaperture input (320×410µm2) ever implemented in an SHFT on-chip spectrometer. The device was fabricated using 248 nm deep-ultraviolet lithography, exhibiting over 13 dB of optical throughput improvement compared to a single-aperture device. The measured resolution varies between 29 and 49 pm within the 1260-1600 nm wavelength range.

Dual-polarization silicon nitride Bragg filters with low thermal sensitivity.

Wideband and polarization-independent wavelength filters with low sensitivity to temperature variations have great potential for wavelength division multiplexing applications. However, simultaneously achieving these metrics is challenging for silicon-on-insulator photonics technology. Here, we harness the reduced index contrast and the low thermo-optic coefficient of silicon nitride to demonstrate waveguide Bragg grating filters with wideband apolar rejection and low thermal sensitivity. Filter birefringence is reduced by judicious design of a triangularly shaped lateral corrugation. Based on this approach, we demonstrate silicon nitride Bragg filters with a measured polarization-independent 40 dB optical rejection with negligible off-band excess loss, and a sensitivity to thermal variations below 20 pm/°C.

SiGe-enhanced Si capacitive modulator integration in a 300 mm silicon photonics platform for low power consumption.

The successful integration of capacitive phase shifters featuring a p-type strained SiGe layer in a 300 mm silicon photonics platform is presented. The phase shift is evaluated with a voltage swing of only 0.9 Vpp, compatible with CMOS technology. A good correlation is shown between the phase shift efficiency from 10 to 60°/mm and the capacitive oxide thickness varying from 15 to 4 nm. Corresponding insertion losses are as low as 3 dB/mm thanks to the development of low loss poly-silicon and to a careful design of the doped layers within the waveguide. The thin SiGe layer brings an additional 20% gain in efficiency due to higher hole efficiency in strained SiGe.

Low loss poly-silicon for high performance capacitive silicon modulators.

Optical properties of poly-silicon material are investigated to be integrated in new silicon photonics devices, such as capacitive modulators. Test structure fabrication is done on 300 mm wafer using LPCVD deposition: 300 nm thick amorphous silicon layers are deposited on thermal oxide, followed by solid phase crystallization anneal. Rib waveguides are fabricated and optical propagation losses measured at 1.31 µm. Physical analysis (TEM ASTAR, AFM and SIMS) are used to assess the origin of losses. Optimal deposition and annealing conditions have been defined, resulting in 400 nm-wide rib waveguides with only 9.2-10 dB/cm losses.

Can land managers control Japanese knotweed? Lessons from control tests in Belgium.

Japanese knotweed Fallopia japonica is an extremely abundant invasive plant in Belgium and surrounding countries. To date, no eradication method is available for land managers facing the invasion of this rhizomatous plant. We tested different chemical herbicides with two application methods (spraying and stem injection), as well as mechanical treatments, on knotweed clones throughout southern Belgium. The tested control methods were selected to be potentially usable by managers, e.g., using legally accepted rates for herbicides. Stem volume, height and density reduction were assessed after one or two years, depending on the control method. Labor estimations were made for each control method. No tested control method completely eradicated the clones. Stem injection with glyphosate-based herbicide (3.6 kg ha(-1) of acid equivalent glyphosate) caused the most damage, i.e., no sprouting shoots were observed the year following the injection. The following year, though, stunted shoots appeared. Among the mechanical control methods, repeated cuts combined with native tree transplanting most appreciably reduced knotweed development. The most efficient methods we tested could curb knotweed invasion, but are not likely to be effective in eradicating the species. As such, they should be included in a more integrated restoration strategy, together with prevention and public awareness campaigns.