RESUMO
Gallium nitride (GaN)-on-sapphire photodetectors are used to measure the ultraviolet (UV) radiance behind a shock wave in support of atmospheric entry sensing technologies. DC spectral response characterization of the GaN-based photodetectors shows a peak response around 365 nm with an UV/visible rejection of an order of magnitude. To conduct in situ measurements of UV shock-layer radiation, the GaN-based photodetectors were installed, without protective packaging, in the test section of a shock tube. The measured UV radiation, in terms of incident optical power on the photodetectors, is in excellent agreement with average UV radiation measured by the shock tube facility spectrometers. Furthermore, the device response after being subjected to the shock wave is unaltered, suggesting that the GaN-based material platform is suitable for implementation in aerospace and other harsh environment sensing applications.
Assuntos
Cristalização/métodos , Nanotecnologia/métodos , Nanotubos de Carbono/química , Nanotubos de Carbono/ultraestrutura , Adesividade , Anisotropia , Módulo de Elasticidade , Substâncias Macromoleculares/química , Teste de Materiais , Conformação Molecular , Tamanho da Partícula , Resistência ao Cisalhamento , Propriedades de Superfície , Resistência à TraçãoRESUMO
We have grown a dense array of vertically aligned carbon nanotubes (CNTs) with a controlled distribution of diameters by using block copolymer micelles to form and pattern catalyst particles. The block copolymer poly(styrene-block-acrylic acid) (PS16500-PAA4500) was dissolved in toluene to form micelles and then loaded with FeCl3. The metal-loaded micelles were spin-coated on Si and then thermally treated to remove the polymer. Using this process, we produced surfaces patterned with iron oxide catalyst particles with particle densities ranging from 1400 microm(-2) to 3800 microm(-2) and a size distribution of (6.9 +/- 0.8) nm. CNT growth by thermal chemical vapor deposition was then performed on these samples. The low-density catalyst sample produced unaligned, low-density CNTs, whereas the high-density catalyst sample produced vertically aligned, dense CNTs about 10 microm in length. Transmission electron microscopy revealed that the CNTs typically had double and triple graphitic layers with normally distributed diameters of (4.5 +/- 1.1) nm. For comparison, CNTs grown from the standard approach of blanket Fe films had a wide distribution of diameters between 6 and 21 nm. This catalyst preparation approach dramatically sharpens the size distribution of CNTs, compared to standard approaches, and provides a simple means of controlling the areal density of CNTs.
RESUMO
Interfacial thermal resistance results of various nanotube and nanofiber coatings, prepared by chemical vapor deposition (CVD) methods, are reported at relatively low clamping pressures. The five types of samples examined include multi-walled and single-walled nanotubes growth by CVD, multi-walled nanotubes grown by plasma enhanced CVD (PECVD) and carbon nanofibers of differing aspect ratio grown by PECVD. Of the samples examined, only high aspect ratio nanofibers and thermally grown multi-walled nanotubes show an improvement in thermal contact resistance. The improvement is approximately a 60% lower thermal resistance than a bare Si-Cu interface and is comparable to that attained by commercially available thermal interface materials.
Assuntos
Cristalização/métodos , Temperatura Alta , Nanotecnologia/métodos , Nanotubos de Carbono/química , Nanotubos de Carbono/ultraestrutura , Teste de Materiais , Propriedades de Superfície , Condutividade TérmicaRESUMO
Plasma-enhanced chemical vapor deposition is used to grow vertically aligned multiwalled carbon nanofibers (MWNFs). The graphite basal planes in these nanofibers are not parallel as in nanotubes; instead they exhibit a small angle resembling a stacked cone arrangement. A parametric study with varying process parameters such as growth temperature, feedstock composition, and substrate power has been conducted, and these parameters are found to influence the growth rate, diameter, and morphology. The well-aligned MWNFs are suitable for fabricating electrode systems in sensor and device development.