EXPRESS: Landmark Publications in Analytical Atomic Spectrometry: Fundamentals and Instrumentation Development.

The almost-two-centuries history of spectrochemical analysis has generated a body of literature so vast that it has become nearly intractable for experts, much less for those wishing to enter the field. Authoritative, focused reviews help to address this problem but become so granular that the overall directions of the field are lost. This broader perspective can be provided partially by general overviews but then the thinking, experimental details, theoretical underpinnings and instrumental innovations of the original work must be sacrificed. In the present compilation, this dilemma is overcome by assembling the most impactful publications in the area of analytical atomic spectrometry. Each entry was proposed by at least one current expert in the field and supported by a narrative that justifies its inclusion. The entries were then assembled into a coherent sequence and returned to contributors for a round-robin review.

Unveiling the mechanisms behind the chemical vapor generation of plumbane for trace analysis of lead.

The mechanisms controlling the generation of PbH4 by reaction of inorganic Pb(II) with aqueous NaBH4 were investigated both in the presence and in the absence of the additive K3Fe(CN)6. For the first time PbH4 has been identified in analytical chemical vapor generation (CVG) by using gas chromatographic mass spectrometry (GC-MS), which allows the use of deuterium labelled experiments. In the absence of the additive, under reaction conditions typically employed for trace lead determination by CVG, Pb(II) is converted to solid species and no volatile lead species can be detected by either atomic or mass spectrometry for Pb(II) concentration up to 100 mg L-1. In alkaline conditions Pb(II) substrates are unreactive towards NaBH4. In the presence of K3Fe(CN)6, deuterium labelled experiments clearly indicated that the generated PbH4 is formed by the direct transfer of hydride from borane to lead atoms. Kinetic experiments were carried out to evaluate the rate of reduction of K3Fe(CN)6 by NaBH4, the rate of hydrolysis of NaBH4 both in the presence and in the absence of K3Fe(CN)6, and the rate of dihydrogen evolution following NaBH4 hydrolysis. The effect of delayed addition of Pb(II) to NaBH4-HCl- K3Fe(CN)6, and K3Fe(CN)6 to NaBH4-HCl-Pb(II) reaction mixtures on the efficiency of plumbane generation was investigated by continuous flow CVG coupled with atomic fluorescence spectrometry. The collected evidences, complemented with thermodynamic considerations and literature data, have made it possible to clarify long-standing controversial aspects related to the mechanism of plumbane generation and the role of K3Fe(CN)6 additive.

Application of direct analysis in real time to study chemical vapor generation mechanisms: reduction of dimethylarsinic(V) acid with aqueous NaBH4 under non-analytical conditions.

The aqueous-phase reaction of dimethylarsinc acid (DMAs(V)) with NaBH4 (THB) was studied under non-analytical conditions (1000 µg/mL As, 0.1 M HCl, 1% NaBH4) with the aim of identifying intermediates and reaction products. The use of direct analysis in real time (DART) with high-resolution mass spectrometry (HRMS), in combination with two different chemical vapor generation systems, allowed the identification of some species not detected by GC-MS such as Me2As-AsMe-AsMe2 and the arsonium species [Me3As-AsMe2]+ and [Me2As-AsMe2-AsMe2]+. Many other methylated species of arsenic containing up to four arsenic atoms have been observed. Unfortunately, the oxidation mechanism that took place in the DART source interfered with the identification of some of those species formed in solution following THB reduction. The species identified by DART-HRMS, together with those previously identified by GC-MS (Me2AsH, Me2AsOH, Me3As, Me3AsO, Me2AsAsMeH, Me2AsAsMe2, and Me2As-O-AsMe2)' enabled the formulation of hypotheses on the possible reaction pathways and revealed an aqueous-phase reactivity of DMAs(V) which could not be explained on the basis of current knowledge. Graphical Abstract.

Application of direct analysis in real time to the study of chemical vapor generation mechanisms: identification of intermediate hydrolysis products of amine-boranes.

In order to elucidate controversial results emerging in chemical vapor generation (CVG) for trace element determination, we conducted a series of experiments devoted to the identification of intermediates formed by acid hydrolysis of amine-boranes. For the first time, direct analysis in real time coupled with high-resolution mass spectrometry (DART-Orbitrap) was applied for detection of this class of compounds. Mass spectra of both solid amine-boranes and their aqueous solutions (pH ~ 8, no hydrolysis) were acquired for understanding their ionization pathway. Mass spectra of aqueous solutions of t-BuNH2·BH3 and Me2NH·BH3 were acquired under conditions that are employed in CVG (0.017-4.0 mol L-1 HCl, 0.167-0.2 mol L-1 borane reagent). The results disclose a reactivity driven by pH of amine-boranes undergoing hydrolysis. At low acidity, the hydrolysis proceeds according to the currently accepted displacement mechanisms (i.e., R3N·BH3 + H3O+ → R3NH+ + H2OBH3). At higher acidity, N-tert-butyl, cyclotriborazane, and bis(dimethylamino)boronium were identified, for the first time, during the hydrolysis of t-BuNH2·BH3 and Me2NH·BH3, respectively. Formation of these intermediates was ascribed to a hydrolysis pathway starting with the ionization of the amine-borane, (i.e., R3N·BH3 + H3O+ → [(H2O)R3NBH2] + + H2). The new evidence explains the anomalous behavior observed in CVG by amine-borane derivatization, and updates the currently accepted mechanisms for the acid hydrolysis of amine-boranes. Graphical Abstract.

Derivatization chemistries for the determination of inorganic anions and structurally related compounds by gas chromatography - A review.

Gas chromatography (GC) methods for the determination of inorganic anions and structurally related compounds are reviewed. In their native form, such analytes are polar and non-volatile, therefore they require derivatization before GC analysis. Several chemistries have been employed to convert anions to volatile molecules with applications to a wide set of analytes: nitrite, nitrate, halides, azide, bromate, iodate, borate, carbonate, thiocyanate, cyanide, sulfide, silicates, phosphates, phosphonates, selenite, selenate, arsenite, arsenate, monomethylarsonic acid, and dimethylarsinic acid have been measured following GC separation. In this review, most derivatization chemistries employed for anions are discussed with attention to molecular aspects of the conversion, experimental conditions, applications to complex sample matrices, and figure of merits.

Influence of environmental and anthropogenic parameters on thallium oxidation state in natural waters.

The abandoned mining area of Valdicastello Carducci (Tuscany, Italy) is characterized by the massive presence of thallium in the acid mine drainages and in the valley stream crossing the region. We previously found that Tl(III), generally considered the less stable oxidation state of thallium, is present both in the stream and in tap water distributed in the area, whereas acid mine drainages only contain Tl(I). These findings posed some concern related to the reactivity and dispersion of this toxic element in the environment. Since the valence state of thallium determines its toxicity, distribution and mobility, the study of thallium redox speciation appears crucial to understand its environmental behaviour. In this work, water samples collected from the mine drainages and the contaminated stream were adopted as model to study the distribution of aqueous Tl(I)/Tl(III) as a function of light exposure and solution properties and composition. The influence of three light sources and organic acids was evaluated. Thallium speciation was also assessed in tap water after treatment with common oxidizing agents, and in the rust crust collected from the public waterworks.

Behavior and kinetic of hydrolysis of amine boranes in acid media employed in chemical vapor generation.

The behavior of NaBH4 (THB) and the amine boranes, NH3BH3 (AB), tertbutylNH2BH3 (TBAB), Me2NHBH3 (DMAB) was investigated in continuous flow chemical vapor generation of H2Se from aqueous SeIV coupled with atomic absorption spectrometry. Unexpected higher efficiency of H2Se generation was obtained with amine boranes compared to THB (TBAB > AB > THB) using millimolar concentration of reductant (0.001-0.1 mol L-1) under strongly acidic conditions (HCl, HClO4, H2SO4, HNO3, 0.5-5 mol L-1 H+). Analytical applicability of the CVG system was tested by the determination of SeIV in natural water samples certified reference materials, using 0.01 mol L-1 TBAB in 0.5 M H2SO4. In order to explain this unexpected higher efficiency of amine boranes with respect of THB, the kinetic of hydrolysis of AB, TBAB and DMAB was investigated in acid media typically employed in chemical vapor generation for trace element determination. The kinetic was investigated by monitoring the rate the hydrogen gas evolved during hydrolysis, using a laboratory made thermostated reaction cell. Kinetics were measured for AB, TBAB and DMAB in 0.1, 0.5, 5 mol L-1 HCl or HClO4 reaction media and in 0.1 mol L-1 cysteine +0.1 mol L-1 HCl or HClO4 buffer, for reaction times from 0 to 30 min. Under strongly acidic conditions, the rates of hydrogen evolution produced by amine boranes hydrolysis appear to be much slower than those predicted by a pseudo-first order reaction and using the rate constants reported in the literature. This suggests that, at elevated acidities (5 mol L-1 HCl or HClO4), the hydrolysis of amine boranes takes place in two steps, generating a first amount of H2 (0.67-1.15 mol) much faster than the remaining about 2 mol. This evidence indicates a different mechanism of hydrolysis to the one accepted in the literature for amine boranes. The relatively high efficiencies of H2Se observed with amine borane reduction of inorganic SeIV at elevated acidities can be addressed to the action of borane intermediates, most probably amine borane cations, formed during amine borane hydrolysis in the same reaction conditions.

Human exposure to thallium through tap water: A study from Valdicastello Carducci and Pietrasanta (northern Tuscany, Italy).

A geological study evidenced the presence of thallium (Tl) at concentrations of concern in groundwaters near Valdicastello Carducci (Tuscany, Italy). The source of contamination has been identified in the Tl-bearing pyrite ores occurring in the abandoned mining sites of the area. The strongly acidic internal waters flowing in the mining tunnels can reach exceptional Tl concentrations, up to 9000µg/L. In September 2014 Tl contamination was also found in the tap water distributed in the same area (from 2 to 10µg/L). On October 3, 2014 the local authorities imposed a Do Not Drink order to the population. Here we report the results of the exposure study carried out from October 2014 to October 2015, and aimed at quantifying Tl levels in 150 urine and 318 hair samples from the population of Valdicastello Carducci and Pietrasanta. Thallium was quantified by inductively coupled plasma - mass spectrometry (ICP-MS). Urine and hair were chosen as model matrices indicative of different time periods of exposure (short-term and long-term, respectively). Thallium values found in biological samples were correlated with Tl concentrations found in tap water in the living area of each citizen, and with his/her habits. Thallium concentration range found in hair and urine was 1-498ng/g (values in unexposed subjects 0.1-6ng/g) and 0.046-5.44µg/L (reference value for the European population 0.006µg/L), respectively. Results show that Tl levels in biological samples were significantly associated with residency in zones containing elevated water Tl levels. The kinetics of decay of Tl concentration in urine samples was also investigated. At the best of our knowledge, this is the first study on human contamination by Tl through water involving such a high number of samples.

Ovalbumin labeling with p-hydroxymercurybenzoate: The effect of different denaturing agents and the kinetics of reaction.

The aim of our study was to investigate how denaturing agents commonly used in protein analysis influence the labeling between a reactive molecule and proteins. For this reason, we investigated the labeling of ovalbumin (OVA) as a globular model protein with p-hydroxymercurybenzoate (pHMB) in its native state (phosphate buffer solution) and in different denaturing conditions (8 molL(-1) urea, 3 molL(-1) guanidinium thiocyanate, 6 molL(-1) guanidinium chloride, 0.2% sodium dodecyl sulfate, and 20% methanol). In addition to chemical denaturation, thermal denaturation was also tested. The protein was pre-column simultaneously denatured and derivatized, and the pHMB-labeled denatured OVA complexes were analyzed by size exclusion chromatography (SEC) coupled online with chemical vapor generation-atomic fluorescence spectrometry (CVG-AFS). The number of -SH groups titrated greatly depends on the protein structure in solution. Indeed, we found that, depending on the adopted denaturing conditions, OVA gave different aggregate species that influence the complexation process. The results were compared with those obtained by a common alternative procedure for the titration of -SH groups that employs monobromobimane (mBBr) as tagging molecule and molecular fluorescence spectroscopy as detection technique. We also investigated the labeling kinetics for denatured OVA and pHMB, finding that the 4 thiolic groups of OVA have a very different reactivity toward mercury labeling, in agreement with previous studies.

Determination of thiocyanate in saliva by headspace gas chromatography-mass spectrometry, following a single-step aqueous derivatization with triethyloxonium tetrafluoroborate.

A novel method for the determination of salivary thiocyanate is presented. Thiocyanate was converted into ethyl thiocyanate by single-step aqueous derivatization based on triethyloxonium tetrafluoroborate and measured by gas chromatography-mass spectrometry (15 min runtime). The ethyl thiocyanate derivative is volatile and can be sampled from the headspace. The derivatization chemistry proposed allows for separation of the analyte from saliva matrix whose introduction in the measurement system is avoided. Quantitation of the analyte was obtained by isotope dilution, employing a (13)C-enriched thiocyanate as internal standard. Technical details and fundamental aspects of derivatization chemistry and calibration strategy are presented. The method was validated by comparison with a standard method based on ion chromatography. The two independent methodologies produced results in agreement within 3%. Also a three level spike recovery test was carried out for validation purpose and quantitative recoveries were attained. The method is fast, simple, safe, and sensitive. Measurement of a 1 mL volume 50 ng/g of thiocyanate standard produced a signal-to-noise ratio of 250 for the analytical peak. This method is therefore suitable for ultra-trace determination of thiocyanate (low part-per-billion range). For the application described the full detection potential of the method was not required and the sample preparation presented has been designed for quantitation of saliva samples containing 1-400 µg/g of thiocyanate with a combined standard uncertainty of 2% relative for saliva samples containing 25 µg/g of thiocyanate. This method was applied for the determination of thiocyanate in human saliva samples.

Direct, simple derivatization of disulfide bonds in proteins with organic mercury in alkaline medium without any chemical pre-reducing agents.

In this work we have studied the derivatization of protein disulfide bonds with p-Hydroxymercurybenzoate (pHMB) in strong alkaline medium without any preliminary reduction. The reaction has been followed by the determination of the protein-pHMB complex using size exclusion chromatography coupled to a microwave/UV mercury oxidation system for the on-line oxidation of free and protein-complexed pHMB and atomic fluorescence spectrometry (SEC-CVG-AFS) detection. The reaction has been optimized by an experimental design using lysozyme as a model protein and applied to several thiolic proteins. The proposed method reports, for the first time, that it is possible to label 75-100% cysteines of proteins and, thus, to determine thiolic proteins without the need of any reducing step to obtain reduced SH groups before mercury labelling. We obtained a detection limit of 100 nmol L(-1) based on a signal-to-noise ratio of 3 for unbound and complexed pHMB, corresponding to a detection limit of proteins ranged between 3 and 360 nmol L(-1), depending on the number of cysteines in the protein sequence.

Impact of protein concentration on the determination of thiolic groups of ovalbumin: a size exclusion chromatography-chemical vapor generation-atomic fluorescence spectrometry study via mercury labeling.

We optimized a hyphenated system based on size exclusion chromatography coupled to a microwave/UV mercury oxidation system and an atomic fluorescence detector (SEC-CVG-AFS) for the online oxidation of free and protein-complexed p-hydroxymercuribenzoic acid (pHMB) without the employment of chemical oxidizing agents. This system has been applied to the study of labeling of thiolic groups of native ovalbumin (OVA) as a function of protein concentration. We found that the protein concentration strongly affects the species distribution of OVA, the number of thiolic groups titrated in each species, and thus, the accuracy in the determination of the total number of thiolic groups. The amount of titrated sulfhydryl groups in the protein concentration range investigated (5-100 µmol L(-1)) varied from 2.40 ± 0.01 to 1.85 ± 0.05 for the monomeric form of OVA and from 4.63 ± 0.01 to 5.63 ± 0.05 for the total OVA, which represents more than four theoretical number of reduced Cys. This information is important from the analytical point of view because it suggests that, unless to operate with diluted concentration of protein, the number of titrated thiolic groups results from both the aspecific interaction of the probe with aggregates species and to the specific bond of the probe with the accessible -SH groups.

Chemical generation of arsane and methylarsanes with amine boranes. Potentialities for nonchromatographic speciation of arsenic.

The efficiency of chemical generation of arsanes from inorganic arsenic, monomethylarsonic acid (MMAA) and dimethylarsinic acid (DMAA), to arsane, AsH3, monomethylarsane, CH3AsH2 (MMA), and dimethylarsane, (CH3)2AsH (DMA), has been investigated in different reaction media with the aim to better elucidate the mechanisms controlling their generation process and to find the experimental conditions to implement a nonchromatographic arsenic speciation analytical method, which is based on the selective determination of some arsenic species. Studies were performed by continuous flow hydride generation coupled with atomic spectrometry (CF-HG-AS), using different reductants such as borane-ammonia (AB), borane-tert-butylamine (TBAB), and sodium tetrahydridoborate (THB) in HCl and HClO4 media, in the presence or absence of L-cysteine (Cys). The efficiency of HG processes for MMA and DMA is mainly controlled by the reactivity of the substrates with the borane, which could be strongly influenced by the formation of ion couples. The protonation of arsane did not play a significant role in the employed reaction system. By taking advantage of the different reactivity pattern of As species in selected generation conditions, DMAA and MMAA could be selectively determined in 0.5 and 10 M HClO4 solutions, respectively, in the presence of Cys, with AB as the reducing agent. The presence of Cys as a masking agent and the peculiar reducing properties of AB ensured a good control of interferences, as far as it has been observed for Co(II), Ni(II), Cu(II), Fe(II), Fe(III). The overall time needed to complete the prereduction step has been verified for MMAA and DMAA at different acidities in order to achieve the best selectivity. The selective determination of DMAA with AB/Cys in HClO4 has been optimized and applied to certified reference materials (CRMs) of natural waters CASS-4, SLRS-4, and NASS-4 (NRCC). The estimation of DMAA concentration allows us to correct the concentration of As(III) for the interference of DMAA in the selective determination of As(III) according to a selective HG method recently reported.

Microwave photochemical reactor for the online oxidative decomposition of p-hydroxymercurybenzoate (pHMB)-tagged proteins and their determination by cold vapor generation-atomic fluorescence detection.

A novel method is presented for the characterization and determination of thiolic proteins. After the labeling with p-hydroxymercurybenzoate, the pHMB-labeled proteins underwent on-line oxidation with a novel microwave (MW)/UV photochemical reactor, followed by cold vapor generation-atomic fluorescence spectrometry (CVG-AFS) detection. The MW/UV process led to the conversion of pHMB to Hg(II) with a yield of 89.0 ± 0.5% without using chemical oxidizing reagents and avoiding the use of toxic carcinogenic compounds. Hg(II) was reduced to Hg(0) in a knotted reaction coil with NaBH4 solution, stripped from the solution by an argon flow and detected. The chromatographic method for labeled thiolic peptides was linear in the 0.2-100 µmol L(-1) range, with a LOD as mercury of 57 nmol L(-1). This system has proven to be a useful interface for liquid chromatography coupled with CVG-AFS in the determination and characterization of thiolic proteins. This method has been applied to the determination of thiolic peptides after tryptic digestion of serum albumins from different species (human, bovine, rat, horse, and sheep).

Determination of thiomersal by flow injection coupled with microwave-assisted photochemical online oxidative decomposition of organic mercury and cold vapor atomic fluorescence spectroscopy.

We developed a flow injection (FI) method for the determination of thiomersal (sodium ethylmercurithiosalicylate, C9H9HgNaO2S) based on the UV/microwave (MW) photochemical, online oxidation of organic mercury, followed by cold vapor generation atomic fluorescence spectrometry (CVG-AFS) detection. Thiomersal was quantitatively converted in the MW/UV process to Hg(II), with a yield of 97±3%. This reaction was followed by the reduction of Hg(II) to Hg(0) performed in a knotted reaction coil with NaBH4 solution, and AFS detection in an Ar/H2 miniaturized flame. The method was linear in the 0.01-2 µg mL(-1) range, with a LOD of 0.003 µg mL(-1). This method has been applied to the determination of thiomersal in ophthalmic solutions, with recoveries ranging between 97% and 101%. We found a mercury concentration in commercial ophthalmic solutions ranging between 7.5 and 59.0 µg mL(-1).

Interaction of collagen with chlorosulphonated paraffin tanning agents: Fourier transform infrared spectroscopic analysis and molecular dynamics simulations.

The binding of chlorosulphonated paraffins to collagen triple helices is studied by means of classical molecular dynamics simulations and experimental spectroscopic techniques in order to disclose the principal characteristics of their interaction during the leather fattening process. Indeed, collagen is the main target to develop new leather modifying agents with specific characteristics, and an accurate design of the collagen binders, supported by predictive computational strategies, could be a successful tool to obtain new effective eco-compatible compounds able to impart to the leather the required functionalities and distinctive mechanical properties. Possible effects caused by the tanning agents on the collagen matrix have been identified from both experimental and theoretical points of view. Computational data in agreement with experiment have revealed that chlorosulphonated paraffins can interact favorably with the collagen residues having amine groups in their side chains (Arg, Lys, Asn and Gln) and reduce the tendency of the solvated collagen matrix to swell. However, the interference of chlorosulphonated paraffins with the unfolding process, which is operated mainly by the action of water, can be due both to covalent cross-linking of the collagen chains and intermolecular hydrogen bonding interactions involving also the hydroxyl groups of Hyp, Ser and Thr residues.

Novel ethyl-derivatization approach for the determination of fluoride by headspace gas chromatography/mass spectrometry.

We report a novel derivatization chemistry for determination of fluoride based on the batch reaction of fluoride ions with triethyloxonium tetrachloroferrate(III) in a closed vessel to yield fluoroethane. Gaseous fluoroethane was readily separated from the matrix, sampled from the headspace, and determined by gas chromatography/mass spectrometry. The method was validated using rainwater certified reference material (IRMM CA408) and subsequently applied to the determination of fluoride in various matrixes, including tap water, seawater, and urine. An instrumental limit of detection of 3.2 µg/L with a linear range up to 50 mg/L was achieved. The proposed derivatization is a one-step reaction, requires no organic solvents, and is safe, as the derivatizing agent is nonvolatile. Determination of fluoride is affected by common fluoride-complexing agents, such as Al(III) and Fe(III). The effect of large amounts of these interferences was studied, and the adverse effect of these ions was eliminated by use of the method of standard additions.

The binomial distribution of hydrogen and deuterium in arsanes, diarsanes, and triarsanes generated from As(III)/[BH(n)D(4-n)]- and the effect of trace amounts of Rh(III) ions.

Recent studies of the formation of arsane in the borohydride/arsenate reaction demonstrate the occurrence of condensation cascades whereby small quantities of di- and triarsanes are formed. In this study, the isotopic composition of these di- and triarsanes was examined using deuterium labelled borohydrides. A statistical model was employed to construct the mass spectra of all diarsane and triarsane isotopologues (As(2)H(n)D(4-n) and As(3)H(n)D(5-n)) from the mass spectra of isotopically pure compounds (As(2)H(4), As(2)D(4), As(3)H(5), and As(3)D(5)). Subsequent deconvolution of the experimental mixed spectra shows that incorporation of hydrogen closely follows the binomial distribution, in accord with arsane formation. The H/D distribution in arsane, diarsane, and triarsane isotopologues is binomial in the absence of any interference. However, this is significantly altered by the presence of some transition metals; presented here, for the first time, are the effects of Rh(III). The presence of Rh(III) in the As(III)/[BD(4)](-) system entails the incorporation of hydrogen into the arsanes arising from the solvent, altering the expected binomial H/D distribution.

Negative chemical ionization GC/MS determination of nitrite and nitrate in seawater using exact matching double spike isotope dilution and derivatization with triethyloxonium tetrafluoroborate.

The alkylation of nitrite and nitrate by triethyloxonium tetrafluoroborate allows determination of their ethyl esters by headspace gas chromatography/mass spectrometry (GC/MS). In the present study, significant improvement in analytical performance is achieved using negative chemical ionization providing detection limits of 150 ng/L for NO(2)(-) and 600 ng/L for NO(3)(-), an order of magnitude better than those achieved using electron impact ionization. The derivatization procedure was optimized and alkaline conditions adopted to minimize conversion of nitrite to nitrate (determined to be 0.07% at 100 mg/L NO(2)(-)) and to avoid the exchange of oxygen between the analytes and the solvent (water). Quantitation entails use of isotopically enriched standards (N(18)O(2)(-) and (15)NO(3)(-)), which also permits monitoring of potential conversion from nitrite to nitrate during the analysis (double spike isotope dilution).