Correlation between Friction and Wear in Cylindrical Anchorages Simulated with Wear Machine and Analyzed with Scanning Probe and Electron Microscope.

This paper presents the possibilities of applying atomic force microscopy (AFM) techniques to the study of the wear of prosthetic biomaterials. In the conducted research, a zirconium oxide sphere was used as a test piece for mashing, which was moved over the surface of selected biomaterials: polyether ether ketone (PEEK) and dental gold alloy (Degulor M). The process was carried out with constant load force in an artificial saliva environment (Mucinox). An atomic force microscope with an active piezoresistive lever was used to measure wear at the nanoscale. The advantage of the proposed technology is the high resolution of observation (less than 0.5 nm) in the three-dimensional (3D) measurements in a working area of 50 × 50 × 10 µm. The results of nano wear measurements in two measurement setups are presented: zirconia sphere (Degulor M and zirconia sphere) and PEEK were examined. The wear analysis was carried out using appropriate software. Achieved results present a tendency coincident with the macroscopic parameters of materials.

Adhesion as a component of retention force of overdenture prostheses-study on selected Au based dental materials used for telescopic crowns using atomic force microscopy and contact angle techniques.

Contemporary prosthetic materials are characterized by highly specific preparation for a given application. This means that at the stage of their creation, not only their function is taken into account, but also the long-term behavior of this material during use. In the case of telescopic crowns, an important factor not yet appearing in the research is the aspect of adhesion force and its dependence on the type of biomaterial, but also the properties of human saliva. The use of artificial saliva, which creates a lubricating layer, reduces the wear on the surface of the telescopic crowns by reducing friction. The impact of artificial saliva on the formation of chemical bonds between prosthetic elements, thus contributing to the so-called retention force has not yet been studied. In this work, two types of measurements of gold telescopic crown materials in the aspect of the adhesion process are presented. Obtained results allowed to fully characterize this phenomenon. We modeled the load force between the microcircuit and the surface under study to suit the conditions between the primary and secondary crowns in the patient's mouth.

Analysis of the electrolytically polished skeletal dentures surfaces using various nano- and microscopic technologies.

PURPOSE: The surface roughness of the dental restorations is significant to the denture plaque adhesion. METHODS: In this work, we present the complex analysis of the electropolished CoCrW alloy remanium® star (Dentaurum, Germany) samples with laserengraved fiducial marks performed using complementary set of micro- and nanoscopic techniques: optical profilometry (OP), atomic force microscopy (AFM), scanning electron microscopy (SEM) and focused ion beam (FIB) milling. RESULTS: Both mean and RMS roughness of the samples were reduced by electopolishing process, however, the results obtained using OP and AFM exhibited some discrepancies. This was caused by the relatively high local protruding defects developed on the processed surface. The cross-sections of the protrusions were made to analyze the cause of their formation as the EDS elemental content maps revealed that their composition was uniform. We also analyzed the local roughness in the smaller areas free from the defects. CONCLUSIONS: In that case, both OP and AFM techniques delivered the same results. Analysis of results showed that various methods used for the surface roughness evaluation have to be used simultaneously to obtain complete and true analysis of the technological CoCrW samples.

A clinical evaluation denture adhesives used by patients with xerostomia.

The purpose of study was to analyze the participants' opinions concerning the effectiveness of 6 denture adhesives (DA). The study group included 60 participants. Criteria for selecting the patients were as follows: reduced retention and stabilization of maxillary complete dentures and xerostomia. These features were evaluated on basis of clinical examination and standard sialometry tests (u-SFR). Retention of maxillary dentures was scored by modified Kapur index before application of DA. All participants were divided randomly into 6 groups regarding the use of the 6 DA during a 6-month period. After this time, participants completed an HRQL questionnaire. DA noticeably improved retention and stabilization of maxillary complete dentures. DA in the glue form had the best retention effectiveness in participants with xerostomia. These materials are difficult to clean from the denture base. The data are presented in tables and figures. The results of the study collected positive influence of adhesives on retention of dentures in xerostomia patients. The cleaning dentures and denture bearing tissues was difficult. DA help in the use of prostheses, but it is also necessary for the treatment of the causes and symptoms of xerostomia.

The role of friction in the mechanism of retaining the partial removable dentures with double crown system.

Cylindrical telescopic crowns belong to bolt dentures, because their adhesion strength is based on the friction force. The magnitude of static and slide friction forces depends on the strain within the contact area and properties of materials employed. Friction force value between telescope elements declines in the first phase of wearing period and, subsequently, maintains particular constant value of 8 to 10 N. In the telescopic technique, homo and heterogenic joints are used. The following prosthodontic materials have been examined: goldbase alloys (Degudent Kiss, Degulor M), cobalt-base alloy (Brealloy 270), ceramics (Zircon Oxide, Zirconia) during tribological investigations on FGP composite resin. The cooperating surfaces were moistened with synthetic saliva. The research confirmed the dependence of the static friction coefficient on the contact pressure for the analyzed pairs of materials used in prosthodontics. The biggest effect of the contact pressure on the coefficient of friction value occurs when the ceramic rubs on FGP composite resin. The most stable friction coefficient in the context of contact pressure changes as well as life has been found in the case of the cobalt alloy Brealloy 270. An interesting material is a gold alloy Degulor M, for which the coefficient of friction varies only slightly with pressure in the range of 0.6 to 0.9 MPa.