An adaptive prosthetic socket for people with transtibial amputation.

It is essential that people with limb amputation maintain proper prosthetic socket fit to prevent injury. Monitoring and adjusting socket fit, for example by removing the prosthesis to add prosthetic socks, is burdensome and can adversely affect users' function and quality-of-life. This study presents results from take-home testing of a motor-driven adaptive socket that automatically adjusted socket size during walking. A socket fit metric was calculated from inductive sensor measurements of the distance between the elastomeric liner surrounding the residual limb and the socket's inner surface. A proportional-integral controller was implemented to adjust socket size. When tested on 12 participants with transtibial amputation, the controller was active a mean of 68% of the walking time. In general, participants who walked more than 20 min/day demonstrated greater activity, less doff time, and fewer manual socket size adjustments for the adaptive socket compared with a locked non-adjustable socket and a motor-driven socket that participants adjusted with a smartphone application. Nine of 12 participants reported that they would use a motor-driven adjustable socket if it were available as it would limit their socket fit issues. The size and weight of the adaptive socket were considered the most important variables to improve.

Beyond step counts: Including wear time in prosthesis use assessment for lower-limb amputation.

Introduction: The purpose of this study was to test a novel activity monitor that tracks the time a prosthesis is worn, and the nature of the ambulatory activity conducted with the prosthesis. These capabilities allow prosthesis users' wear and accommodation practices (e.g., temporary doffing) to be monitored, and the intensity of their activities to be assessed. Methods: A portable limb-socket motion sensing system was used to monitor doffs, walk bouts (≥5 steps), low locomotion (2-4 steps), stationary positions, and weight shifts in a group of transtibial prosthesis users. The relationship between doff time and active motion time was investigated, and durations of low and high intensity active motions were compared. Results: For the 14 participants tested, the median prosthesis day duration ranged from 12.8-18.8 h. Eleven participants typically doffed five or fewer times per day, and three participants typically doffed 10 or more times per day. Nine participants demonstrated a positive correlation between daily doff duration and active motion duration. Six participants spent more time in weight shifts than walk bouts, while eight participants spent more time in walk bouts than weight shifts. Conclusion: Capturing don time and temporary doffs and distinguishing weight shifts from walks may provide insight relevant to patient care. Longer-term monitoring studies should be conducted, and the clinical utility of the data evaluated.

Using magnetic panels to enlarge a transtibial prosthetic socket.

A novel method is described to connect a prosthetic liner to the panels of an adjustable socket to facilitate limb fluid volume stabilization in prosthesis users. Magnets are placed in the socket panels, and iron powder is embedded in the user's prosthetic liner. When the magnet is in close proximity to the liner, a firm connection is formed. The system's capability to execute panel pull on transtibial prosthesis users was tested. The backs of the panels were supported by a bracket mounted to the external surface of the socket that allowed the radial position of the panels to be adjusted. Bench testing demonstrated an optimized strength-to-weight ratio using 1.27-cm thick annular-shaped magnets supported by 0.32-cm thick backplates. Testing on four people with transtibial amputation showed that the maximum socket increase achieved using magnetic panel pull ranged from 5.3% to 13.8% of the initial (panels flush) socket volume. The results indicate that magnetic panel pull induces a meaningful increase in socket volume during sitting. The clinical relevance is a novel strategy that may help stabilize prosthesis users' limb fluid volume over the day.

A novel portable sensor to monitor bodily positions and activities in transtibial prosthesis users.

BACKGROUND: Step activity monitors provide insight into the amount of physical activity prosthesis users conduct but not how they use their prosthesis. The purpose of this research was to help fill this void by developing and testing a technology to monitor bodily position and type of activity. METHODS: Thin inductive distance sensors were adhered to the insides of sockets of a small group of transtibial prosthesis users, two at proximal locations and two at distal locations. An in-lab structured protocol and a semi-structured out-of-lab protocol were video recorded, and then participants wore the sensing system for up to 7 days. A data processing algorithm was developed to identify sit, seated shift, stand, standing weight-shift, walk, partial doff, and non-use. Sensed distance data from the structured and semi-structured protocols were compared against the video data to characterize accuracy. Bodily positions and activities during take-home testing were tabulated to characterize participants' use of the prosthesis. FINDINGS: Sit and walk detection accuracies were above 95% for all four participants tested. Stand detection accuracy was above 90% for three participants and 62.5% for one participant. The reduced accuracy may have been due to limited stand data from that participant. Step count was not proportional to active use time (sum of stand, walk, and standing weight-shift times). INTERPRETATION: Step count may provide an incomplete picture of prosthesis use. Larger studies should be pursued to investigate how bodily position and type of activity may facilitate clinical decision-making and improve the lives of people with lower limb amputation.

Performance of an auto-adjusting prosthetic socket during walking with intermittent socket release.

Introduction: A challenge in the engineering of auto-adjusting prosthetic sockets is to maintain stable operation of the control system while users change their bodily position and activity. The purpose of this study was to test the stability of a socket that automatically adjusted socket size to maintain fit. Socket release during sitting was conducted between bouts of walking. Methods: Adjustable sockets with sensors that monitored distance between the liner and socket were fabricated. Motor-driven panels and a microprocessor-based control system adjusted socket size during walking to maintain a target sensed distance. Limb fluid volume was recorded continuously. During eight sit/walk cycles, the socket panels were released upon sitting and then returned to position for walking, either the size at the end of the prior bout or a size 1.0% larger in volume. Results: In six transtibial prosthesis users, the control system maintained stable operation and did not saturate (move to and remain at the end of the actuator's range) during 98% of the walking bouts. Limb fluid volume changes generally matched the panel position changes executed by the control system. Conclusions: Stable operation of the control system suggests that the auto-adjusting socket is ready for testing in users' at-home settings.