Multi-institution single geometry plan complexity characteristics based on IROC phantoms.

BACKGROUND: Clinical intensity modulated radiation therapy plans have been described using various complexity metrics to help identify problematic radiotherapy plans. Most previous studies related to the quantification of plan complexity and their utility have relied on institution-specific plans which can be highly variable depending on the machines, planning techniques, delivery modalities, and measurement devices used. In this work, 1723 plans treating one of only four standardized geometries were simultaneously analyzed to investigate how radiation plan complexity metrics vary across four different sets of common objectives. PURPOSE: To assess the treatment plan complexity characteristics of plans developed for Imaging and Radiation Oncology Core (IROC) phantoms. Specifically, to understand the variability in plan complexity between institutions for a common plan objective, and to evaluate how various complexity metrics differentiate relevant groups of plans. METHODS: 1723 plans treating one of four standardized IROC phantom geometries representing four different anatomical sites of treatment were analyzed. For each plan, 22 MLC-descriptive plan complexity metrics were calculated, and principal component analysis (PCA) was applied to the 22 metrics in order to evaluate differences in plan complexity between groups. Across all metrics, pairwise comparisons of the IROC phantom data were made for the following classifications of the data: anatomical phantom treated, treatment planning system (TPS), and the combination of MLC model and treatment planning system. An objective k-means clustering algorithm was also applied to the data to determine if any meaningful distinctions could be made between different subgroups. The IROC phantom database was also compared to a clinical database from the University of Wisconsin-Madison (UW) which included plans treating the same four anatomical sites as the IROC phantoms using a TrueBeam™ STx and Pinnacle3 TPS. RESULTS: The IROC head and neck and spine plans were distinct from the prostate and lung plans based on comparison of the 22 metrics. All IROC phantom plan group complexity metric distributions were highly variable despite all plans being designed for identical geometries and plan objectives. The clusters determined by the k-means algorithm further supported that the IROC head and neck and spine plans involved similar amounts of complexity and were largely distinct from the prostate and lung plans, but no further distinctions could be made. Plan complexity in the head and neck and spine IROC phantom plans were similar to the complexity encountered in the UW clinical plans. CONCLUSIONS: There is substantial variability in plan complexity between institutions when planning for the same objective. For each IROC anatomical phantom treated, the magnitude of variability in plan complexity between institutions is similar to the variability in plan complexity encountered within a single institution database containing several hundred unique clinical plans treating corresponding anatomies in actual patients.

Thermoluminescent dosimeters (TLD-100) for absorbed dose measurements in alpha-emitting radionuclides.

Early works that used thermoluminescent dosimeters (TLDs) to measure absorbed dose from alpha particles reported relatively high variation (10%) between TLDs, which is undesirable for modern dosimetry applications. This work outlines a method to increase precision for absorbed dose measured using TLDs with alpha-emitting radionuclides by applying an alpha-specific chip factor (CF) that individually characterizes the TLD sensitivity to alpha particles. Variation between TLDs was reduced from 21.8% to 6.7% for the standard TLD chips and 7.9% to 3.3% for the thin TLD chips. It has been demonstrated by this work that TLD-100 can be calibrated to precisely measure the absorbed dose to water from alpha-emitting radionuclides.

Beam quality correction factors for ionization chambers in a 0.35 T magnetic resonance (MR)-linac - A Monte Carlo study.

PURPOSE: The purpose of this study was to directly calculate [Formula: see text] correction factors for four cylindrical ICs for a 0.35 T MR-linac using the Monte Carlo (MC) method. METHODS: A previously-validated TOPAS/GEANT4 MC head model of the 0.35 T MR-linac was employed. The MR-compatible Exradin A12, A1SL, A26, and A28 cylindrical ICs were modeled considering the dead volume in the air cavity. The [Formula: see text] correction factor was determined for initial electron energies of 5-7 MeV. The correction factor was calculated for all four angular orientations in the lateral plane. The impact of the 0.35 T magnetic field on the IC response was also investigated. RESULTS: The maximum beam quality dependence in the [Formula: see text] exhibited by the A12, A1SL, A26, and A28 ICs was 1.10 %, 2.17 %, 0.81 %, and 1.75 %, respectively, considering all angular orientations. The magnetic field dependence was < 1 % and the maximum [Formula: see text] correction was < 2 % when the detector was aligned along the direction of the magnetic field at 0° and 180° angles. The A12 IC over-responded up to 5.40 % for the orthogonal orientation. An asymmetry in the response of up to 8.30 % was noted for the A28 IC aligned at 90° and 270° angles. CONCLUSIONS: A parallel orientation for the IC, with respect to the magnetic field, is recommended for reference dosimetry in MRgRT. Both over and under-response in the IC signal was noted for the orthogonal orientations, which is highly dependent on the cavity diameter, cavity length, and the dead volume.

Characterization of a segmented printed circuit board (PCB) as a standard for absorbed dose to water from alpha-emitting radionuclides.

BACKGROUND: Our previous work introduced and evaluated a standard for surface absorbed dose rate per unit radioactivity to water from unsealed alpha-emitting radionuclides used in targeted radionuclide therapy (TRT). An overall uncertainty over 4.0% at k = 1 was reported for the absorbed dose to air measurements, which was partially attributed to the rotational alignment uncertainty in the geometrical setup. PURPOSE: A printed circuit board (PCB) with a segmented guard was constructed to align the extrapolation chamber (EC) and the source plates using a differential capacitance technique. The PCB EC aimed to enhance the repeatability of the ionization current measurements. The PCB EC was evaluated using a thin film 210Po source. The measured absorbed dose to air cavity was compared with the Monte Carlo (MC) calculations. Using the extrapolation method, the surface absorbed dose rate to water was calculated. METHODS: The PCB EC was constructed with a 4.50 mm diameter collector surrounded by four sectors and a guard electrode. The sectors were isolated for rotational alignment and later connected to the guard for ionization current measurements. A bridge circuit measured differential capacitance between opposing sectors, and a hexapod motion stage rotated the source substrate to minimize the differential capacitance. The EC was evaluated using a 210Po source with a 3.20 mm diameter and 1.253 µ $\mu $ Ci radioactivity. MC simulations were performed to calculate the k p o i n t ${k}_{point}$ , k b a c k s c a t t e r ${k}_{backscatter}$ , and k d i v ${k}_{div}$ correction factors. Ionization current measurements were performed for air gaps in the 0.3-0.525 mm range and surface absorbed dose rate to water was calculated. RESULTS: Rotational offsets of up to 3.0° were found and the current repeatability was found to increase with the absorbed dose to air uncertainty calculated to be ∼2.0%. Using the capacitance method, the effective EC diameter was measured to be 4.53 mm. The recombination, polarity, and electrometer corrections were reported to be within 1.00% across all measurement trials. The MC-calculated correction factors were calculated to be much larger than the recombination and polarity correction factors. The average k p o i n t ${k}_{point}$ , k b a c k s c a t t e r ${k}_{backscatter}$ , and k d i v ${k}_{div}$ corrections were calculated to be 1.063, 0.9402, and 2.136, respectively. The MC-calculated absorbed dose to air was found to overestimate the absorbed dose by over 4.00% when compared with the measured absorbed dose to air. The surface absorbed dose rate to water was calculated to be 2.304 × 10 - 6 $2.304 \times {10}^{ - 6}$ Gy/s/Bq with an overall uncertainty of 4.07%. CONCLUSIONS: The constructed PCB EC was deemed suitable as an absorbed dose standard. A repeatable rotational alignment was achieved using the differential capacitance technique. The metal electrodes on the PCB made a difference of < 1.00% on the backscatter correction when compared to the EC comprised of polystyrene-equivalent collector. A 20% difference in the surface absorbed dose rate to water was found between the two ECs, which is attributed to the cavity diameter differences leading to different magnitudes of dose fall-off along the lateral direction.

A diffusion-leakage model coupled with dose point kernels (DPK) for dosimetry of diffusing alpha-emitters radiation therapy (DaRT).

BACKGROUND: Diffusing alpha-emitters radiation therapy (DaRT) is a novel brachytherapy technique that leverages the diffusive flow of 224Ra progeny within the tumor volume over the course of the treatment. Cell killing is achieved by the emitted alpha particles that have a short range in tissue and high linear energy transfer. The current proposed absorbed dose calculation method for DaRT is based on a diffusion-leakage (DL) model that neglects absorbed dose from beta particles. PURPOSE: This work aimed to couple the DL model with dose point kernels (DPKs) to account for dose from beta particles as well as to consider the non-local deposition of energy. METHODS: The DaRT seed was modeled using COMSOL multiphysics and the DL model was implemented to extract the spatial information of the diffusing daughters. Using Monte-Carlo (MC) methods, DPKs were generated for 212Pb, 212Bi, and their progenies since they were considered to be the dominant beta emitters in the 224Ra radioactive decay chain. A convolution operation was performed between the integrated number densities of the diffusing daughters and DPKs to calculate the total absorbed dose over a 30-day treatment period. Both high-diffusion and low-diffusion cases were considered. RESULTS: The calculated DPKs showed non-negligible energy deposition over several millimeters from the source location. An absorbed dose >10 Gy was deposited within a 1.8 mm radial distance for the low diffusion case and a 2.2 mm radial distance for the high diffusion case. When the DPK method was compared with the local energy deposition method that solely considered dose from alpha particles, differences above 1 Gy were found within 1.3 and 1.8 mm radial distances from the surface of the source for the low diffusion and high diffusion cases, respectively. CONCLUSIONS: The proposed method enhances the accuracy of the dose calculation method used for the DaRT technique.

Minimum reporting standards should be expected for preclinical radiobiology irradiators and dosimetry in the published literature.

The cornerstones of science advancement are rigor in performing scientific research, reproducibility of research findings and unbiased reporting of design and results of the experiments. For radiation research, this requires rigor in describing experimental details as well as the irradiation protocols for accurate, precise and reproducible dosimetry. Most institutions conducting radiation biology research in in vitro or animal models do not have describe experimental irradiation protocols in sufficient details to allow for balanced review of their publication nor for other investigators to replicate published experiments. The need to increase and improve dosimetry standards, traceability to National Institute of Standards and Technology (NIST) standard beamlines, and to provide dosimetry harmonization within the radiation biology community has been noted for over a decade both within the United States and France. To address this requirement subject matter experts have outlined minimum reporting standards that should be included in published literature for preclinical irradiators and dosimetry.

Dose-rate dependence and IMRT QA suitability of EBT3 radiochromic films for pulse reduced dose-rate radiotherapy (PRDR) dosimetry.

BACKGROUND: Pulsed reduced dose rate (PRDR) is an emerging radiotherapy technique for recurrent diseases. It is pertinent that the linac beam characteristics are evaluated for PRDR dose rates and a suitable dosimeter is employed for IMRT QA. PURPOSE: This study sought to investigate the pulse characteristics of a 6 MV photon beam during PRDR irradiations on a commercial linac. The feasibility of using EBT3 radiochromic film for use in IMRT QA was also investigated by comparing its response to a commercial diode array phantom. METHODS: A plastic scintillator detector was employed to measure the photon pulse characteristics across nominal repetition rates (NRRs) in the 5-600 MU/min range. Film was irradiated with dose rates in the 0.033-4 Gy/min range to study the dose rate dependence. Five clinical PRDR treatment plans were selected for IMRT QA with the Delta4 phantom and EBT3 film sheets. The planned and measured dose were compared using gamma analysis with a criterion of 3%/3 mm. EBT3 film QA was performed using a cumulative technique and a weighting factor technique. RESULTS: Negligible differences were observed in the pulse width and height data between the investigated NRRs. The pulse width was measured to be 3.15 ± 0.01 µ s $\mu s$ and the PRF was calculated to be 3-357 Hz for the 5-600 MU/min NRRs. The EBT3 film was found to be dose rate independent within 3%. The gamma pass rates (GPRs) were above 99% and 90% for the Delta4 phantom and the EBT3 film using the cumulative QA method, respectively. GPRs as low as 80% were noted for the weighting factor EBT3 QA method. CONCLUSIONS: Altering the NRRs changes the mean dose rate while the instantaneous dose rate remains constant. The EBT3 film was found to be suitable for PRDR dosimetry and IMRT QA with minimal dose rate dependence.

Biological Characterization of the Effects of Filtration on the Xoft Axxent® Electronic Brachytherapy Source for Cervical Cancer Applications.

Low-energy X-ray sources that operate in the kilovoltage energy range have been shown to induce more cellular damage when compared to their megavoltage counterparts. However, low-energy X-ray sources are more susceptible to the effects of filtration on the beam spectrum. This work sought to characterize the biological effects of the Xoft Axxent® source, a low-energy therapeutic X-ray source, both with and without the titanium vaginal applicator in place. It was hypothesized that there would be an increase in relative biological effectiveness (RBE) of the Axxent® source compared to 60Co and that the source in the titanium vaginal applicator (SIA) would have decreased biological effects compared to the bare source (BS). This hypothesis was drawn from linear energy transfer (LET) simulations performed using the TOPAS Monte Carlo user code as well a reduction in dose rate of the SIA compared to the BS. A HeLa cell line was maintained and used to evaluate these effects. Clonogenic survival assays were performed to evaluate differences in the RBE between the BS and SIA using 60Co as the reference beam quality. Neutral comet assay was used to assess induction of DNA strand damage by each beam to estimate differences in RBE. Quantification of mitotic errors was used to evaluate differences in chromosomal instability (CIN) induced by the three beam qualities. The BS was responsible for the greatest quantity of cell death due to a greater number of DNA double strand breaks (DSB) and CIN observed in the cells. The differences observed in the BS and SIA surviving fractions and RBE values were consistent with the 13% difference in LET as well as the factor of 3.5 reduction in dose rate of the SIA. Results from the comet and CIN assays were consistent with these results as well. The use of the titanium applicator results in a reduction in the biological effects observed with these sources, but still provides an advantage over megavoltage beam qualities. © 2023 by Radiation Research Society.

Determination of an air kerma-rate correction factor for the S7600 Xoft AxxentⓇ source model.

PURPOSE: The purpose of this work was to provide guidance for the lack of an air-kerma rate standard for the S7600 Xoft Axxent® source by providing a correction factor to apply to the National Institute of Standards and Technology (NIST) traceable S7500 well chamber (WC) calibration coefficient before the development of an S7600 standard at NIST. METHODS AND MATERIALS: The Attix free air chamber (FAC) at the University of Wisconsin Medical Radiation Research Center was used to measure the air-kerma rate at 50 cm for six S7500 and six S7600 sources. These same sources were then measured using five standard imaging HDR1000+ WCs. The measurements made with the FAC were used to calculate source-specific WC calibration coefficients for the S7500 and S7600 source. These results were compared to the NIST traceable calibration coefficients for the S7500 source. The average results for each WC were then averaged together, and a ratio of the S7600 to S7500 WC calibration coefficients was determined. RESULTS: The average S7600 air-kerma rate measurement with the FAC was 7% lower than the average air-kerma rate measurements of the S7500 source. On average, the S7500 determined WC calibration coefficients agreed within ±1% of the NIST traceable S7500 values. The S7600 WC calibration coefficients were up to 16% less than the NIST traceable S7500 values. The final correction factor determined to be applied to the NIST traceable S7500 value was 0.8415 with an associated uncertainty of ±8.1% at k = 2. CONCLUSIONS: This work provides a suggested correction factor for the S7600 Xoft Axxent source such that the sources can be accurately implemented in the clinical setting.

Measurement of the modified TG43 parameters for the bare S7600 Xoft Axxent source model.

PURPOSE: The purpose of this work is to provide measured data for the modified TG43 parameters [DeWerd et al.] for the newest, Galden-cooled S7600 Xoft Axxent source model. METHODS: The measurement of radial dose distributions at distances of 1 cm to 4 cm from the source was performed using TLD100 microcubes, EBT3 film, and an Exradin A26 microionization chamber. The overall uncertainty and reproducibility of each dosimeter was evaluated for its use in determining the radial dose function and dose rate conversion coefficient. An acrylic phantom developed in house for previous works was used to measure the polar anisotropy function using TLD100 microcubes at distances of 1 cm, 2 cm, and 5 cm from the source. RESULTS: The Exradin A26 chamber was deemed most suitable for measuring the radial dose function. Values determined had a maximum k = 1 uncertainty of 1.4%. The dose rate conversion coefficient measured with the chamber was found to be 9.33 ± 0.21cGy/hrµGy/min. TLD100 microcube measurements of the polar anisotropy had average uncertainties of 6%, 3%, and 2.5% at 1 cm, 2 cm, and 5 cm, respectively. CONCLUSIONS: The modified TG43 parameters for the bare source were measured with reasonable uncertainty. The values determined will aid with the clinical implementation of the source for breast and endometrial cancer applications.

An independent Monte Carlo-based IMRT QA tool for a 0.35 T MRI-guided linear accelerator.

PURPOSE: To develop an independent log file-based intensity-modulated radiation therapy (IMRT) quality assurance (QA) tool for the 0.35 T magnetic resonance-linac (MR-linac) and investigate the ability of various IMRT plan complexity metrics to predict the QA results. Complexity metrics related to tissue heterogeneity were also introduced. METHODS: The tool for particle simulation (TOPAS) Monte Carlo code was utilized with a previously validated linac head model. A cohort of 29 treatment plans was selected for IMRT QA using the developed QA tool and the vendor-supplied adaptive QA (AQA) tool. For 27 independent patient cases, various IMRT plan complexity metrics were calculated to assess the deliverability of these plans. A correlation between the gamma pass rates (GPRs) from the AQA results and calculated IMRT complexity metrics was determined using the Pearson correlation coefficients. Tissue heterogeneity complexity metrics were calculated based on the gradient of the Hounsfield units. RESULTS: The median and interquartile range for the TOPAS GPRs (3%/3 mm criteria) were 97.24% and 3.75%, respectively, and were 99.54% and 0.36% for the AQA tool, respectively. The computational time for TOPAS ranged from 4 to 8 h to achieve a statistical uncertainty of <1.5%, whereas the AQA tool had an average calculation time of a few minutes. Of the 23 calculated IMRT plan complexity metrics, the AQA GPRs had correlations with 7 out of 23 of the calculated metrics. Strong correlations (|r| > 0.7) were found between the GPRs and the heterogeneity complexity metrics introduced in this work. CONCLUSIONS: An independent MC and log file-based IMRT QA tool was successfully developed and can be clinically deployed for offline QA. The complexity metrics will supplement QA reports and provide information regarding plan complexity.

On the perturbation effect and LET dependence of beam quality correction factors in carbon ion beams.

BACKGROUND: In a recent study, we reported beam quality correction factors, fQ , in carbon ion beams using Monte Carlo (MC) methods for a cylindrical and a parallel-plate ionization chamber (IC). A non-negligible perturbation effect was observed; however, the magnitude of the perturbation correction due to the specific IC subcomponents was not included. Furthermore, the stopping power data presented in the International Commission on Radiation Units and Measurements (ICRU) report 73 were used, whereas the latest stopping power data have been reported in the ICRU report 90. PURPOSE: The aim of this study was to extend our previous work by computing fQ correction factors using the ICRU 90 stopping power data and by reporting IC-specific perturbation correction factors. Possible energy or linear energy transfer (LET) dependence of the fQ correction factor was investigated by simulating both pristine beams and spread-out Bragg peaks (SOBPs). METHODS: The TOol for PArticle Simulation (TOPAS)/GEANT4 MC code was used in this study. A 30 × 30 × 50 cm3 water phantom was simulated with a uniform 10 × 10 cm2 parallel beam incident on the surface. A Farmer-type cylindrical IC (Exradin A12) and two parallel-plate ICs (Exradin P11 and A11) were simulated in TOPAS using the manufacturer-provided geometrical drawings. The fQ correction factor was calculated in pristine carbon ion beams in the 150-450 MeV/u energy range at 2 cm depth and in the middle of the flat region of four SOBPs. The kQ correction factor was calculated by simulating the fQo correction factor in a 60 Co beam at 5 cm depth. The perturbation correction factors due to the presence of the individual IC subcomponents, such as the displacement effect in the air cavity, collecting electrode, chamber wall, and chamber stem, were calculated at 2 cm depth for monoenergetic beams only. Additionally, the mean dose-averaged and track-averaged LET was calculated at the depths at which the fQ was calculated. RESULTS: The ICRU 90 fQ correction factors were reported. The pdis correction factor was found to be significant for the cylindrical IC with magnitudes up to 1.70%. The individual perturbation corrections for the parallel-plate ICs were <1.0% except for the A11 pcel correction at the lowest energy. The fQ correction for the P11 IC exhibited an energy dependence of >1.00% and displayed differences up to 0.87% between pristine beams and SOBPs. Conversely, the fQ for A11 and A12 displayed a minimal energy dependence of <0.50%. The energy dependence was found to manifest in the LET dependence for the P11 IC. A statistically significant LET dependence was found only for the P11 IC in pristine beams only with a magnitude of <1.10%. CONCLUSIONS: The perturbation and kQ correction factor should be calculated for the specific IC to be used in carbon ion beam reference dosimetry as a function of beam quality.

A multi-institutional comparison of acceptance testing data for a 0.35 T MRI scanner.

Objective.To present and quantify the variability in the acceptance testing data for the imaging component of the 0.35 T magnetic resonance-linear accelerator (MR-linac).Approach.The current acceptance testing protocol by the MR-linac vendor was described along with the equipment and scanner parameters utilized throughout the process. TheBofield homogeneity, SNR/uniformity of the combined and individual receiver coils, American College of Radiology (ACR) image quality testing, and spatial integrity of the imaging data were collected from twelve different institutions. The variability in the results was accentuated and the ramifications of the results were discussed in the context of MR-guided radiation therapy.Main Results.TheBofield homogeneity was found to have a large gantry dependence with the median values being <4 ppm for all gantry angles. The SNR and uniformity were found to be well above the vendor-specified thresholds with a relatively small institutional-dependence. All institutions passed the ACR image uniformity tests. The largest institutional variability was noted to be for the slice positional accuracy test. The spatial fidelity was calculated to be <1.0 and <2.1 mm within a 100 and a 175 mm radius from the isocenter.Significance.The results from this study can be used to set the tolerances and formal guidelines for MR-linacs imaging quality assurance. Additionally, the multi-institutional data reported in this work will aid in future MR-linac acceptance and commissioning.

GEC-ESTRO ACROP recommendations on calibration and traceability of HE HDR-PDR photon-emitting brachytherapy sources at the hospital level.

The vast majority of radiotherapy departments in Europe using brachytherapy (BT) perform temporary implants of high- or pulsed-dose rate (HDR-PDR) sources with photon energies higher than 50 keV. Such techniques are successfully applied to diverse pathologies and clinical scenarios. These recommendations are the result of Working Package 21 (WP-21) initiated within the BRAchytherapy PHYsics Quality Assurance System (BRAPHYQS) GEC-ESTRO working group with a focus on HDR-PDR source calibration. They provide guidance on the calibration of such sources, including practical aspects and issues not specifically accounted for in well-accepted societal recommendations, complementing the BRAPHYQS WP-18 Report dedicated to low energy BT photon emitting sources (seeds). The aim of this report is to provide a European-wide standard in HDR-PDR BT source calibration at the hospital level to maintain high quality patient treatments.

On the length used for CT ionization chambers to determine CTDI.

Objective.Computed tomography dose index (CTDI) calculations based on measurements made with CT ionization chambers require characterization of two chamber properties: radiation sensitivity and effective length. The sensitivity of a CT ionization chamber is currently determined in some countries by calibration in an x-ray field that irradiates the entire chamber. Determination of the effective length is left to the user, and this value is frequently assumed to be equivalent to the nominal length-typically 100 mm-stated by the manufacturer. This assumption undermines the intention and usefulness of CTDI calculation. Thus, a slit-based calibration,NKL, of the CT ionization chambers was proposed by collimating the x-ray beam to a well-defined aperture width. The aim of this work is to compare the two methods.Approach.Four different CT ionization chambers (Standard Imaging Exradin A101, Radcal 10x5-3CT, Victoreen 500-100, and Capintec PC-4P) are investigated in this work. Sensitivity profiles were measured for all four chambers and effective/rated chamber lengths were calculated. A novel Monte-Carlo based correction was proposed to account for the presence of the aperture. CTDI was calculated and compared for two calibration beams as well as for a commercial CT scanner using Exradin A101 and Radcal 10x5-3CT chambers.Main results.The nominal chamber length was found to deviate up to 21% compared to the effective length. Correction for the aperture depended on the aperture opening size. CTDI calculation results illustrate the potential 17% error in CTDI calculation that can be caused by assuming the effective chamber length is equivalent to the manufacturer's stated nominal length. CTDI calculations with CT ionization chambers calibrated with an air-kerma length calibration method yield the smallest variation in the CTDI regardless of the chamber model.Significance.To avoid an erroneous CTDI, information regarding the chamber's effective length must be included in the calibration or stated by the manufacturer. Alternatively, a slit-based calibration can be performed.

A multi-institutional comparison of dosimetric data for a 0.35 T MR-linac.

Objective.A comparison of percent depth dose (PDD) curves, lateral beam profiles, output factors (OFs), multileaf collimator (MLC) leakage, and couch transmission factors was performed between ten institutes for a commercial 0.35 T MR-linac.Approach.The measured data was collected during acceptance testing of the MR-linac. The PDD curves were measured for the 3.32 × 3.32 cm2, 9.96 × 9.96 cm2, and 27.20 × 24.07 cm2field sizes. The lateral beam profiles were acquired for a 27.20 × 24.07 cm2field size using an ion chamber array and penumbra was defined as the distance between 80% of the maximum dose and 20% of the maximum dose after normalizing the profiles to the dose at the inflection points. The OFs were measured using solid-state dosimeters, whereas radiochromic films were utilized to measure radiation leakage through the MLC stacks. The relative couch transmission factors were measured for various gantry angles. The variation in the multi-institutional data was quantified using the percent standard deviation metric.Main results.Minimal variations (<1%) were found between the PDD data, except for the build-up region and the deeper regions of the PDD curve. The in-field region of the lateral beam profiles varied <1.5% between different institutions and a small variation (<0.7 mm) in penumbra was observed. A variation of <1% was observed in the OF data for field sizes above 1.66 × 1.66 cm2, whereas large variations were shown for small-field sizes. The average and maximum MLC leakage was calculated to be <0.3% and <0.6%, which was well below the international electrotechnical commission (IEC) leakage thresholds. The couch transmission was smallest for oblique beams and ranged from 0.83 to 0.87.Significance.The variation in the data was found to be relatively small and the different 0.35 T MR-linacs were concluded to have similar dosimetric characteristics.

Comparison of air kerma rate between the S7500 and S7600 xoft axxent sources.

PURPOSE: The purpose of this work was to evaluate differences in air-kerma rate of the older, S7500 water-cooled Xoft Axxent source and newer, S7600 Galden-cooled source. METHODS AND MATERIALS: The Attix Free Air Chamber (FAC) at the UWMRRC was used to measure the air-kerma rate at 50 cm for six S7600 Xoft Axxent sources. The average measured air-kerma of the S7600 sources was compared with the measured average air-kerma rate from five S7500 sources. The air-kerma rates of the S7500 sources were measured in a Standard Imaging HDR 1000+ well chamber. The FAC measurements were used to determine a well chamber calibration coefficient for the S7600 source. The S7500 calibration coefficients were incorrectly applied to the S7600 sources to indicate the magnitude of error that can occur if the incorrect calibration coefficient is used. RESULTS: A 10.3% difference was observed between the average air-kerma rates of the two sources although a 17% difference was observed between their calibration coefficients. The application of the S7500 calibration coefficient to the S7600 sources resulted in measured air-kerma rates that were 20% greater than the true value. CONCLUSIONS: This work indicates the need for a new air-kerma rate standard for the S7600 sources, and the results presented in this work are indicative of values that would be obtained at National Institute of Standards and Technology.