Alkylammonium Halides for Phase Regulation and Luminescence Modulation of Cesium Copper Iodide Nanocrystals for Light-Emitting Diodes.

All-inorganic cesium copper halide nanocrystals have attracted extensive attention due to their cost-effectiveness, low toxicity, and rich luminescence properties. However, controlling the synthesis of these nanocrystals to achieve a precise composition and high luminous efficiency remains a challenge that limits their future application. Herein, we report the effect of oleylammonium iodide on the synthesis of copper halide nanocrystals to control the composition and phase and modulate their photoluminescence (PL) quantum yields (QYs). For CsCu2I3, the PL peak is centered at 560 nm with a PLQY of 47.3%, while the PL peak of Cs3Cu2I5 is located at 440 nm with an unprecedently high PLQY of 95.3%. Furthermore, the intermediate-state CsCu2I3/Cs3Cu2I5 heterostructure shows white light emission with a PLQY of 66.4%, chromaticity coordinates of (0.3176, 0.3306), a high color rendering index (CRI) of 90, and a correlated color temperature (CCT) of 6234 K, indicating that it is promising for single-component white-light-emitting applications. The nanocrystals reported in this study have excellent luminescence properties, low toxicity, and superior stability, so they are more suitable for future light-emitting applications.

RGB tri-luminescence in organic-inorganic zirconium halide perovskites.

Materials with two or more fluorescence features under different excitation sources have great potential in optical applications, but luminous materials with three emission characteristics have been largely undeveloped. Here, we report a novel zero-dimensional (0D) organic-inorganic hybrid ((C2H5)4N)2ZrCl6 perovskite with multiple emissions. The zirconium-based perovskite exhibits a red emission around 620 nm, a green emission at 527 nm, and a blue emission around 500 nm. The red and green emissions come from self-trapped excitons (STEs) and the d-d transitions of Zr(iv), respectively, which are caused by distortion of the [ZrCl6]2- octahedra. The blue emission is caused by thermally activated delayed fluorescence (TADF), which is similar to that of Cs2ZrCl6. The absolute photoluminescence quantum yield (PLQY) of the red and blue double emission is up to 83% and the PLQY of the green emission is 27%. With different combinations of ((C2H5)4N)2ZrCl6 samples, we achieve a variety of applications, including a two-color luminescent anti-counterfeiting device, a white light-emitting diode (WLED) with a color rendering index (CRI) of 95 and information encryption with different excitations. We also synthesize other hybrid zirconium perovskites with tri-luminescence through a similar method. Our work provides a potential set of excitation-dependent luminescent materials and is expected to expand the basic research and practical applications of multi-luminescence materials.

Bioinspired, vertically stacked, and perovskite nanocrystal-enhanced CMOS imaging sensors for resolving UV spectral signatures.

Imaging and identifying target signatures and biomedical markers in the ultraviolet (UV) spectrum is broadly important to medical imaging, military target tracking, remote sensing, and industrial automation. However, current silicon-based imaging sensors are fundamentally limited because of the rapid absorption and attenuation of UV light, hindering their ability to resolve UV spectral signatures. Here, we present a bioinspired imaging sensor capable of wavelength-resolved imaging in the UV range. Inspired by the UV-sensitive visual system of the Papilio xuthus butterfly, the sensor monolithically combines vertically stacked photodiodes and perovskite nanocrystals. This imaging design combines two complementary UV detection mechanisms: The nanocrystal layer converts a portion of UV signals into visible fluorescence, detected by the photodiode array, while the remaining UV light is detected by the top photodiode. Our label-free UV fluorescence imaging data from aromatic amino acids and cancer/normal cells enables real-time differentiation of these biomedical materials with 99% confidence.

Solid-state synthesis of cesium manganese halide nanocrystals in glass with bright and broad red emission for white LEDs.

Recently, lead halide perovskite nanocrystals (NCs) have attracted extensive attention due to their unique optical properties. However, the toxicity of lead and the instability to moisture obstruct their further commercial development. Herein, a series of lead-free CsMnX3 (X = Cl, Br, and I) NCs embedded in glasses were synthesized by a high temperature solid-state chemistry method. These NCs embedded in glass can remain stable after soaking in water for 90 days. It is found that increasing the amount of cesium carbonate in the synthesis process can not only prevent the oxidation of Mn2+ to Mn3+ and promote the transparency of glass in the 450-700 nm region, but also significantly increase its photoluminescence quantum yield (PLQY) from 2.9% to 65.1%, which is the highest reported value of the red CsMnX3 NCs so far. Using CsMnBr3 NCs with a red emission peak at 649 nm and full-width-at-half-maximum (FWHM) of 130 nm as the red light source, a white light-emitting diode (LED) device with International Commission on illumination (CIE) coordinates of (0.33, 0.36) and a color rendering index (CRI) of 94 was obtained. These findings, together with future research, are likely to yield stable and bright lead-free NCs for the next generation of solid-state lighting.

Luminescence Enhancement of CsMnBr3 Nanocrystals through Heterometallic Doping.

The absorption and photoluminescence (PL) of CsMnBr3 with Mn(II) in octahedral crystal fields are extremely weak due to a d-d forbidden transition. Herein, we introduce a facile and general synthetic procedure that can prepare undoped and heterometallic doped CsMnBr3 NCs at room temperature. Importantly, both PL and absorption of CsMnBr3 NCs were significantly improved after doping a small amount of Pb2+ (4.9%). The absolute photoluminescence quantum yield (PL QY) of Pb-doped CsMnBr3 NCs is up to 41.5%, 11-fold higher than undoped CsMnBr3 NCs (3.7%). The PL enhancement is attributed to the synergistic effects between [MnBr6]4- units and [PbBr6]4- units. Furthermore, we verified the similar synergistic effects between [MnBr6]4- units and [SbBr6]4- units in Sb-doped CsMnBr3 NCs. Our results highlight the potential of tailoring luminescence properties of manganese halides through heterometallic doping.

Full-colour Jabuticaba-like nanostructures via the multiplex and orthogonal self-assembly of protein-conjugated quantum dots with engineered biofilms.

The integration of inorganic components with bacterial biofilms is of great significance for expanding the functionality of artificial biological materials. However, so far, the complexities and functionalities of biofilm-based scaffolds assembled via metal-peptide coordination chemistries remain limited. Here, we present a platform for the multiplexed and specific coupling of recombinant protein-functionalized fluorescent red-green-blue (RGB) quantum dots (QDs) with engineered biofilms to form Jabuticaba-like nanostructures. Full-color living Jabuticaba-like nanostructures have been achieved through the interaction of extracellular peptides that are fabricated by biofilms with the proteins that modify the surface of the RGB QDs through orthogonal SpyTag/SpyCatcher, IsopeptagN/PilinN, and IsopeptagC/PilinC pairs. We envision that living cell populations will enable the multiplexable, scalable and bottom-up assembly of versatile materials that integrate both abiotic and biotic components into multifunctional systems.

Synthesis of Efficient and Stable Tetrabutylammonium Copper Halides with Dual Emissions for Warm White Light-Emitting Diodes.

In order to achieve a high color-rendering index (CRI) and low correlated color temperature (CCT) indoor lighting, single-component phosphors with broad-band dual emission are in high demand for white-light-emitting diodes (WLEDs). However, phosphors with such fluorescent properties are rare at present. Herein, we report a facile solid-state chemical method for the synthesis of single-component phosphor with broad-band emission and a large Stokes shift that can meet the requirements of future white-light sources. These new tetrabutylammonium copper halides phosphors have excellent warm white emission characteristics, and their luminescence peaks are located at 494 and 654 nm. The optimized photoluminescence (PL) quantum yield can reach 93.7 %. The typical CIE coordinate of the as-fabricated WLED is at (0.3620, 0.3731) with a CRI of 89 and low CCT of 4516 K.

Surface passivation of intensely luminescent all-inorganic nanocrystals and their direct optical patterning.

All-inorganic nanocrystals (NCs) are of great importance in a range of electronic devices. However, current all-inorganic NCs suffer from limitations in their optical properties, such as low fluorescence efficiencies. Here, we develop a general surface treatment strategy to obtain intensely luminescent all-inorganic NCs (ILANs) by using designed metal salts with noncoordinating anions that play a dual role in the surface treatment process: (i) removing the original organic ligands and (ii) binding to unpassivated Lewis basic sites to preserve the photoluminescent (PL) properties of the NCs. The absolute photoluminescence quantum yields (PLQYs) of red-emitting CdSe/ZnS NCs, green-emitting CdSe/CdZnSeS/ZnS NCs and blue-emitting CdZnS/ZnS NCs in polar solvents are 97%, 80% and 72%, respectively. Further study reveals that the passivated Lewis basic sites of ILANs by metal cations boost the efficiency of radiative recombination of electron-hole pairs. While the passivation of Lewis basic sites leads to a high PLQY of ILANs, the exposed Lewis acidic sites provide the possibility for in situ tuning of the functions of NCs, creating opportunities for direct optical patterning of functional NCs with high resolution.

Ultra-small α-CsPbI3 perovskite quantum dots with stable, bright and pure red emission for Rec. 2020 display backlights.

The synthesis of α-CsPbI3 perovskite quantum dots (QDs) with pure red emission around 630 nm is in high demand for display backlight application. However, the phase transition of α-CsPbI3 to yellow non-emitting δ-CsPbI3 has been proven to be a great challenge for the classic colloidal synthesis route for perovskite QDs in octadecene (ODE). Herein, we report a novel colloidal synthesis route by replacing ODE with lauryl methacrylate (LMA) as the reaction solvent to improve the solubility of precursors, resulting in small sized α-CsPbI3 QDs with a diameter of only 4.2 nm, which are the smallest red PQDs reported so far. The corresponding CsPbI3 QD films exhibit a tunable photoluminescence (PL) emission peak in the bright pure red region of 627 to 638 nm. The CsPbI3 QD polymer composite films with PL emission at 630 nm exhibit a superior photoluminescence quantum yield (PLQY) and photostability to mixed halide CsPbBrI2 films under intense illumination. Perovskite light emitting diodes (LED) with the color gamut reaching 96% of the Rec. 2020 standard are achieved using these films. This study provides a high-performance pure red fluorescent material with a robust, low-cost, and reproducible colloidal chemistry that will pave the way for the adoption of perovskite QDs in display backlight application.

Facile Synthesis of Highly Emissive All-Inorganic Manganese Bromide Compounds with Perovskite-Related Structures for White LEDs.

Lead-free all-inorganic halide materials with different Mn2+-based crystal structures (Cs3MnBr5 and CsMnBr3) were obtained using a convenient synthetic method. Cs3MnBr5 had a bright green emission (522 nm), with a unique single-exponential lifetime (τavg = 236 µs) and a high photoluminescence quantum yield (82 ± 5%). A red emission was observed in the case of the CsMnBr3 structure with a two-exponential fluorescence decay curve, and the lifetime was 1.418 µs (93%) and 18.328 µs (7%), respectively. By a judicious tuning of the synthetic conditions, a mixed phase of Cs3MnBr5/CsMnBr3 was also produced that emitted white light, covering almost the entire visible spectrum. White-light-emitting diodes (WLEDs) with color coordinates (0.4269, 0.4955), a color temperature of (3773 K), and a color rendering index (68) were then fabricated using the as-prepared powder of mixed phases of Cs3MnBr5/CsMnBr3 with a commercial UV LED chip (365 nm).

Promoting the doping efficiency and photoluminescence quantum yield of Mn-doped perovskite nanocrystals via two-step hot-injection.

Manganese-doped perovskite nanocrystals (NCs) have been synthesized by a novel two-step hot-injection strategy with an unprecedented Mn doping efficiency of 48.5%, bright orange emission under ultraviolet light and X-ray excitation and a photoluminescence quantum yield of 84.4%, making them excellent luminescent materials.

A general approach to realizing perovskite nanocrystals with insulating metal sulfate shells.

The strategy of constructing the core/shell structure is of great importance in emitting semiconductor nanocrystals. However, the coating on soft metal halide perovskite nanocrystals at the single particle level remains a challenge because of the low compatibility between perovskites and common wide-band-gap semiconductors, such as ZnS and CdS. In addition, using these semiconductors as the shell layer requires high reaction temperatures, which often lead to undesirable chemical transformation. Herein we report a general route to passivate the perovskite nanocrystals by insulating metal sulfate shells. The passivating shell is created around the as-synthesized CsPbBr3 perovskite nanocrystals by initiating the reaction between an organic ammonium sulfate and a variety of metal ions in the presence of ligands. This new method allowed for creating insulating metal sulfate shells with controllable thicknesses and without unwanted chemical transformation. Importantly, these novel core/shell-structured nanocrystals show photoluminescence quantum yields near unity, highly suppressed energy transfer in film and suppressed halide exchange in solution.

All-Inorganic Quantum-Dot LEDs Based on a Phase-Stabilized α-CsPbI3 Perovskite.

The all-inorganic nature of CsPbI3 perovskites allows to enhance stability in perovskite devices. Research efforts have led to improved stability of the black phase in CsPbI3 films; however, these strategies-including strain and doping-are based on organic-ligand-capped perovskites, which prevent perovskites from forming the close-packed quantum dot (QD) solids necessary to achieve high charge and thermal transport. We developed an inorganic ligand exchange that leads to CsPbI3 QD films with superior phase stability and increased thermal transport. The atomic-ligand-exchanged QD films, once mechanically coupled, exhibit improved phase stability, and we link this to distributing strain across the film. Operando measurements of the temperature of the LEDs indicate that KI-exchanged QD films exhibit increased thermal transport compared to controls that rely on organic ligands. The LEDs exhibit a maximum EQE of 23 % with an electroluminescence emission centered at 640 nm (FWHM: ≈31 nm). These red LEDs provide an operating half-lifetime of 10 h (luminance of 200 cd m-2 ) and an operating stability that is 6× higher than that of control devices.

Lead-free Mn-doped antimony halide perovskite quantum dots with bright deep-red emission.

We reported the first synthesis of Mn2+ doped Cs3Sb2Clx/Br9-x (0 ≤ x ≤ 9) perovskite quantum dots (PQDs) by regulating the coprecipitation of Mn2+ and Sb3+ with thiol ligands. These lead-free PQDs demonstrated bright photoluminescence emission centered at 660 nm and a high quantum yield of ∼49%, making them suitable for optical applications.

Synthesis of two-dimensional phenylethylamine tin-lead halide perovskites with bandgap bending behavior.

Recently, two-dimensional (2D) metal halide perovskite materials with wide application in perovskite-based solar cells have attracted significant attention. Among them, 2D mixed lead-tin perovskites have not been systematically explored. Herein, we synthesize a 2D phenethylammonium (PEA) tin-lead bromide perovskite, PEA2Sn x Pb1-x Br4, via a simple solution-phase approach without toxic reagents and high temperatures. By tuning the ratio of Sn and Pb, the UV-vis absorption spectra showed unique bandgap bending behaviors. DFT calculations indicate the key effects of spin-orbital coupling (SOC) without the interference of lattice distortion. Moreover, we provided the standard equation with a correction term to introduce the influence of SOC. These results not only provide a step forward towards the bandgap engineering of perovskites, but also help to expand the application of 2D perovskite materials.

Efficient and Stable Thin-Film Luminescent Solar Concentrators Enabled by Near-Infrared Emission Perovskite Nanocrystals.

A novel triphenylphosphine (TPP) treatment strategy was developed to prepare the near-infrared emission CsPbI3 nanocrystal (NC)-polymer composite thin-film luminescent solar concentrators (LSCs) featuring high absolute photoluminescence quantum yield (PLQY), low reabsorption, and high stability. The PL emission of the LSCs is centered at about 700 nm with 99.4±0.4 % PLQY and narrow full width at half maximum (FWHM) of 75 meV (30 nm). Compared with LSCs prepared with classic CsPbI3 NCs, the stability of the LSCs after TPP treatments has been greatly improved, even after long-term (30 days) immersion in water and strong mercury-lamp irradiation (50 mW cm-2 ). Owing to the presence of lone-pair electrons on the phosphorus atom, TPP is also used as a photoinitiator, with higher efficiency than other common photoinitiators. Large-area (ca. 75 cm2 ) infrared LSCs were achieved with a high optical conversion efficiency of 3.1 % at a geometric factor of 10.

Wash-induced multicolor tuning of carbon nano-dot/micro-belt hybrids with full recyclability and stable color convertibility.

Multicolor carbon phosphors as emerging light conversion materials, with full recyclability and stable color convertibility, are poised to accelerate the sustainable development of environment-friendly optoelectronics. Herein, we firstly report a facile strategy, combining single-step hydrothermal and differential washing methods, for the preparation of multicolor carbon emitters with nano-dot/micro-belt structures. The as-prepared hybrids exhibit excellent film-forming ability and demonstrate controllable multicolor solid-state luminescence ranging from white and green to blue light emission, by utilizing the synergistic effect between nano-dot and micro-belt structures. Particularly, the hybrid white emitters possess a robust ability of being fully recyclable without any performance degradation and formation of harmful byproducts. Moreover, light-emitting devices (LEDs) coated with the hybrid emitters show stable voltage-independent luminescence behavior in lighting applications. This work provides a simple route to modulate the optical properties of multicolor carbon-based emitters and shows great potential in the sustainable development of lighting-related products.

Aqueous acid-based synthesis of lead-free tin halide perovskites with near-unity photoluminescence quantum efficiency.

Recently, lead halide perovskites with outstanding emission performance have become new candidate materials for light-emitting devices and displays; however, the toxicity of lead and instability of halide perovskites remain significant challenges. Herein, we report the aqueous acid-based synthesis of highly emissive two-dimensional (2D) tin halide perovskites, (octylammonium)2SnX4 (X = Br, I, or mixtures thereof), which displayed a high absolute photoluminescence (PL) quantum yield of near-unity in the solid-state, PL emission centered at 600 nm with a broad bandwidth (136 nm), a large Stokes shift (250 nm), long-lived luminescence (τ = 3.3 µs), and zero overlap between their absorption and emission spectra. Significantly, the stability study of 2D tin halide perovskites monitored by the PL quantum yield showed no changes after 240 days of storage at room temperature under ambient air and humidity conditions. The PL emission of the 2D tin halide perovskites was tuned from yellow to deep red by controlling halide composition. Furthermore, new yellow phosphors with superior optical properties are used to fabricate UV pumped white light emitting diodes (WLEDs). We expect these results to facilitate the development of new environmentally friendly and high-performance phosphors for future lighting and display technologies.

Direct Hot-Injection Synthesis of Lead Halide Perovskite Nanocubes in Acrylic Monomers for Ultrastable and Bright Nanocrystal-Polymer Composite Films.

In recent years, lead halide perovskite nanocrystals (NCs) have attracted significant attention in both fundamental research and commercial applications because of their excellent optical and optoelectrical properties. However, the protective ligands on the surface of the perovskite NCs could be easily removed after the tedious process of centrifugation, separation, and dispersion, which greatly hampers their stability against light, heat, moisture, and oxygen and limits their practical applications. Here, we report a new post-processing free strategy (i.e., without centrifugation, separation, and dispersion process) of using an ultraviolet (UV)-polymerizable acrylic monomer of lauryl methacrylate as the solvent to synthesize CsPbBr3 NCs, and then adding polyester polyurethane acrylate oligomer, monomer (IBOA), and initiator for direct UV polymerization to fabricate NC-polymer composite films. These films exhibited an improved photoluminescence quantum yield (85-90%) than classic NC films (40-50%), which were processed using octadecene (ODE) as the solvent for NC synthesis and postprocessed for UV polymerization. Significantly, the as-fabricated films by post-processing free strategy exhibited excellent photostability against strong Xe lamp illumination; while the other films using classic methods were quickly photodegraded. Meanwhile, these NC-polymer composite films showed good stability against moisture and heating when aging in water at 50 °C for over 200 h. These films, along with K2SiF6:Mn4+ (KSF) phosphor emitters, were used as downconverters for blue light-emitting diodes in liquid-crystal displays with a wide color gamut of 115% in the International Commission on Illumination (CIE) 1931 color space. This work provides a facile and effective strategy for the preparation of ultrastable and bright color-conversion NC films for the development of the next-generation wide color gamut displays.

Quench-resistant and stable nanocarbon dot/sheet emitters with tunable solid-state fluorescence via aggregation-induced color switching.

Nanocarbon fluorescence materials are promising color converters for multicolor emission via phosphor-coated light emitting devices (LEDs). Herein, a facile time-controlled solvothermal route was developed to prepare solid-state multicolor nanocarbon emitters comprising dot/sheet nanohybrids. The nanocarbons demonstrate an aggregation-induced color switching behavior, leading to tunable light emission from blue to yellow by modulating the solvothermal reaction time. Particularly, these emitters show outstanding film-forming ability directly and a high production yield (∼40%). Moreover, the nanocarbon-coated ultraviolet LEDs exhibit high quality multicolor light emission and excellent color stability at high voltages, impelling the development of emerging carbon phosphors in fundamental research studies and practical applications.