RESUMO
BACKGROUND: One of the primary concerns in the paediatric emergencies is traumatic dental injuries. OBJECTIVE: This study aimed to create trauma in primary teeth and reveal its effects finite element analysis. DESIGN: Three-dimensional models were created using cone-beam computed tomography images, representing a maxillary primary central incisor. An impact force moving at a speed of 10 m/s was simulated on the labial tooth surface in two directions: buccal and incisal. RESULTS: The stress and deformation experienced in the adjacent tooth due to the primary tooth were higher than those generated in the permanent tooth. Forces applied in the incisal direction resulted in higher levels of stress and deformation in the permanent tooth germ. The difference between the stress and deformation values in primary teeth in the forces applied in the buccal and incisal directions is 21% and 75%, respectively; in the permanent tooth germ, this difference was 233% and 100%, respectively. CONCLUSIONS: Based on the findings of this study, it is crucial to thoroughly evaluate not only the affected primary tooth but also the adjacent teeth and the permanent tooth germ in traumatic dental injuries. This comprehensive examination allows for the anticipation and management of potential long-term problems.
RESUMO
Distal femur fractures are a common problem in orthopedics. Intramedullary retrograde nails (IRN) and dynamic condylar screws (DCS) are generally used for the treatment of these fractures. In this study, it was aimed to mechanically evaluate and compare these two implants used for the treatment of distal femur fractures. In this study, an AOOTA 33C1.3 fracture was created on the intact femur obtained from computed tomography images. The fractures were fixed with DCS and IRN. Then the created models were imported into the ANSYS Workbench for finite element analysis to determine the most convenient mechanical fixation type. The distal region of the femur was loaded considering 75 kg-f, and the created models were constrained in all directions from the femoral head. The intact femur was also analyzed to compare it with the DCS and IRN fixation models. The von Mises stress, strain, and displacement results were examined to determine the damage risk. According to the results, the risk of damage is lower in the model of fixation with IRN. The normal strain distribution in the model fixed with IRN is closer to the model of an intact femur. For this reason, the risk of stress shielding in IRN fixation is less than in DCS fixation. However, the fracture lines were more stable in the fixation with the DCS. In conclusion, fracture fixation with IRN is mechanically more suitable for distal femur fractures in terms of fracture healing.
Assuntos
Fraturas Femorais Distais , Fraturas do Fêmur , Fixação Intramedular de Fraturas , Humanos , Fraturas do Fêmur/diagnóstico por imagem , Fraturas do Fêmur/cirurgia , Parafusos Ósseos , Fêmur/diagnóstico por imagem , Fêmur/cirurgia , Fixação Intramedular de Fraturas/métodosRESUMO
PURPOSE: Ponticulus posticus (PP) is a variation of the bone bridge that appears in the first cervical vertebra and through which the vertebral artery passes. Odontoid fractures are common spinal bone fractures in older people. This study aims to investigate the effect of neck movements on the odontoid and transverse atlantal ligament (TAL) of people with PP variation from a biomechanical view. METHOD: C1, C2, and C3 vertebrae of the occipital bone were analyzed using the finite element method (FEM). In this study, solid models were created with the help of normal (N), incomplete (IC), and asymmetric complete (AC) PP tomography images. The necessary elements for the models were assigned, and the material properties were defined for the elements. As boundary conditions, models were fixed from the C3 vertebra, and 74 N loading was applied from the occipital bone. Stress and deformation values in the odontoid and transverse atlantal ligament were obtained by applying 1.8 Nm moment in flexion, extension, bending, and axial rotation directions. RESULTS: The stress and deformation values of all three models in odontoid and TAL were obtained, and numerical results were evaluated. In all models, stress and deformation values were obtained in decreasing order in rotation, bending, extension, and flexion movements. The highest stress and strain values were obtained in AC and the lowest values were obtained in N. In all movements of the three models, the stress and deformation values obtained in the TAL were lower than in the odontoid. CONCLUSION: The greatest stresses and deformations obtained in spines (AC) with PP were found in the odontoid. This may help explain the pathogenesis of odontoid fractures in older people. First, this study explains the mechanism of the formation of neck trauma in people with PP and the need for a more careful evaluation of the direction of impact. Secondly, the study reveals that the rotational motion of the neck independent of PP has more negative effects on the odontoid.
Assuntos
Atlas Cervical , Processo Odontoide , Humanos , Idoso , Atlas Cervical/diagnóstico por imagem , Processo Odontoide/diagnóstico por imagem , Análise de Elementos Finitos , Fenômenos Biomecânicos , Vértebras Cervicais/diagnóstico por imagem , Ligamentos Articulares/diagnóstico por imagem , Amplitude de Movimento ArticularRESUMO
PURPOSE: The purpose of this study is to research the effect of suture button (SB) fixation, a method used at the treatment of ankle syndesmosis injury, which was applied in various angles, pretension force, and levels, on the distal tibiofibular joint (DTFJ) in the mid-stance phase, with the help of three-dimensional finite elements method (FEM) METHOD: The ankle of a healthy individual was digitally analyzed by a finite element method-based package computer program. Then, anterior inferior tibiofibular ligament (AITFL), interosseous ligament, posterior inferior tibiofibular ligament (PITFL) and deltoid ligament (DL) were cut and force and rotation has been applied to the proximal tibia, resulting in syndesmosis injury. Then, various suture button applications on the injured model have been analyzed. Three parameters have been changed; which were divergence in the axial plane (20°, 30°, 40°), distance from the ankle (2, 3, 4 cm), and pretension force (200, 300, 600 N) RESULTS: As the result of this study, the rotation, change in the gap between the distal tibia and distal fibula, and the displacements of the fibula in the x and y axes have been obtained, and numerical results were evaluated. As the force increased, rotation, change in the gap between the distal tibia and distal fibula, and the displacements of the fibula decreased. As suture button application rotation increased, change in the gap between the distal tibia and distal fibula, and displacements of the fibula increased. As the distance from the ankle increases and reaches a certain level, the results converge to those of the healthy model; in the proximal, it diverges from healthy results. CONCLUSION: In the study, it has been shown that abnormal tibiofibular joint movements can be prevented with suture button application, and optimum application parameters (divergence in the axial plane, distance from the ankle, and pretension force) are given for proper reduction.