The Involvement of Human Papilloma Virus in Gastrointestinal Cancers.

Human Papilloma Virus (HPV) is one of the most common sexually transmitted infections worldwide. HPV infection has a strong relationship with the onset of cervix uteri, vagina, penis, anus, and oropharynx, but also tonsils and tongue cancers. Some epidemiological data indicate that except for gynecologic cancers, HPV infection can be one of the risk factors associated with a greater risk of induction and progression of gastrointestinal cancers. Data, however, remain contradictory and definite conclusions cannot be drawn, so far. The following review aims to organize recent evidence and summarize the current state of knowledge regarding the association between HPV infection and gastrointestinal tumors primarily focusing on esophageal, liver, gastric, colorectal, and anal cancers.

High-Performance Method of Recovery of Metals from EAF Dust-Processing without Solid Waste.

A highly effective method of the processing of steelmaking dust in an arc-resistant furnace has been presented. The aim of the research was to investigate the possibility of processing steelmaking dust in terms of waste minimization and selective recovery of valuable components. For this purpose, an electric arc resistance furnace was used. Granulated steelmaking dust with reducer (coal dust) was the input material. The products of the process are zinc oxide, iron alloy and slag, with properties meeting high ecological requirements. The technology does not generate solid waste. Zinc recovery is over 99% and iron recovery over 98%. The content of heavy metals (Zn + Pb + Cu) in glassy slag is below 0.2%, which ensures very low leachability.

Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies.

Lightweight alloys made from aluminium are used to manufacture cars, trains and planes. The main parts most often manufactured from thin sheets requiring the use of milling in the manufacturing process are front panels for control systems, housing parts for electrical and electronic components. As a result of the final phase of the manufacturing process, cold rolling, residual stresses remain in the surface layers, which can influence the cutting processes carried out on these materials. The main aim of this study was to verify whether the strategy of removing the outer material layers of aluminium alloy sheets affects the surface roughness after the face milling process. EN AW-6082-T6 aluminium alloy thin plates with three different thicknesses and with two directions relative to the cold rolling process direction (longitudinal and transverse) were analysed. Three different strategies for removing the outer layers of the material by face milling were considered. Noticeable differences in surface roughness 2D and 3D parameters were found among all machining strategies and for both rolling directions, but these differences were not statistically significant. The lowest values of Ra = 0.34 µm were measured for the S#3 strategy, which asymmetrically removed material from both sides of the plate (main and back), for an 8-mm-thick plate in the transverse rolling direction. The highest values of Ra = 0.48 µm were measured for a 6-mm-thick plate milled with the S#2 strategy, which symmetrically removed material from both sides of the plate, in the longitudinal rolling direction. However, the position of the face cutter axis during the machining process was observed to have a significant effect on the surface roughness. A higher surface roughness was measured in the areas of the tool point transition from the up-milling direction to the down-milling direction (tool axis path) for all analysed strategies (Ra = 0.63-0.68 µm). The best values were obtained for the up-milling direction, but in the area of the smooth execution of the process (Ra = 0.26-0.29 µm), not in the area of the blade entry into the material. A similar relationship was obtained for analysed medians of the arithmetic mean height (Sa) and the root-mean-square height (Sq). However, in the case of the S#3 strategy, the spreads of results were the lowest.

Jumping Wave Characteristic during Low Plasticity Burnishing Process.

During the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The research concerns the changes in the surface structure of the processed material as well as changes in the structure of the material during this process. The research shows changes in the geometric structure of the surface made in the 3D system and their parametric description. Moreover, the work presents an analysis of the metallographic structure in the tool zone. The research showed occurrence of material slippages in the wave in front of the tool, which creates an additional structure on the surface. These tests make it possible to better understand the process of changes that take place in the surface layer of the processed element in the low plasticity burnishing process.

A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing.

The article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed material was an alloy steel Ø40 mm rod with a hardened surface covered with a thin layer of chromium. The hardness of the outer layer was 547 HV with a core hardness of 180 HV. The surface topography measurements of the processed workpieces were carried out with the 3D Optical Profiler, which supplied information on the irregularities of the processed material texture. In each of the analyzed cases, a corrugated surface was obtained after sawing, which is the effect of the occurrence of the washboarding phenomenon, despite the fact that the teeth of each band saw had variable pitches. The washboarding phenomenon when cutting rods with hard surfaces is caused by the phenomenon of wave regeneration. Despite the use of variable pitch saw blades, the cutting process results in rippling of the sawn surface, which is caused by the high hardness of the outer layer of the workpiece, as well as by the type of tool with spring setting of teeth.

An artificial elementary eye with optic flow detection and compositional properties.

We describe a 2 mg artificial elementary eye whose structure and functionality is inspired by compound eye ommatidia. Its optical sensitivity and electronic architecture are sufficient to generate the required signals for the measurement of local optic flow vectors in multiple directions. Multiple elementary eyes can be assembled to create a compound vision system of desired shape and curvature spanning large fields of view. The system configurability is validated with the fabrication of a flexible linear array of artificial elementary eyes capable of extracting optic flow over multiple visual directions.

Miniature curved artificial compound eyes.

In most animal species, vision is mediated by compound eyes, which offer lower resolution than vertebrate single-lens eyes, but significantly larger fields of view with negligible distortion and spherical aberration, as well as high temporal resolution in a tiny package. Compound eyes are ideally suited for fast panoramic motion perception. Engineering a miniature artificial compound eye is challenging because it requires accurate alignment of photoreceptive and optical components on a curved surface. Here, we describe a unique design method for biomimetic compound eyes featuring a panoramic, undistorted field of view in a very thin package. The design consists of three planar layers of separately produced arrays, namely, a microlens array, a neuromorphic photodetector array, and a flexible printed circuit board that are stacked, cut, and curved to produce a mechanically flexible imager. Following this method, we have prototyped and characterized an artificial compound eye bearing a hemispherical field of view with embedded and programmable low-power signal processing, high temporal resolution, and local adaptation to illumination. The prototyped artificial compound eye possesses several characteristics similar to the eye of the fruit fly Drosophila and other arthropod species. This design method opens up additional vistas for a broad range of applications in which wide field motion detection is at a premium, such as collision-free navigation of terrestrial and aerospace vehicles, and for the experimental testing of insect vision theories.

Quantifying information transfer through a head-attached vibrotactile display: principles for design and control.

Vibrotactile displays can extend the perception capabilities of visually impaired persons. Placing such devices on the head promises easy attachment and detachment without reducing other interaction abilities. However, the effectiveness of head-attached vibrotactile displays has never been thoroughly tested. This paper presents the results obtained from experiments with 22 subjects equipped with a display containing 12 coin-type motors equally spaced in a horizontal plane around the upper head region. Our display allowed single- as well as multimotor activation with up to six simultaneously active motors. We identified the minimum and comfort strength of vibrotactile stimulation, and measured the precision in perceiving the accurate number of active motors as well as the precision in localizing the stimuli on the head. While subjects identified the correct number of active motors in 94% of the cases when presented with only one active motor, this precision dropped to 40% for two and down to 5% for five simultaneously active motors. This strongly suggests to avoid multipoint stimulation even though the precision of localizing a position of a stimulus on the head is barely affected by the number of simultaneously active motors. Localization precision, however, varied significantly with the region of the head suggesting that the most front and back regions of the head should be avoided if high precision is required.