Green Synthesis of Copper Nanoparticles Using Sargassum spp. for Electrochemical Reduction of CO2.

This study presents a green method of producing copper nanoparticles (CuNPs) using aqueous extracts from Sargassum spp. as reducing, stabilizing, and capping agents. The CuNPs created using this algae-based method are not hazardous, they are eco-friendly, and less toxic than their chemically synthesized counterparts. The XRD characterization of the CuNPs revealed the presence of Cu and CuO, with a crystallite size ranging from 13 to 17 nm. Following this, the CuNPs were supported onto a carbon substrate, also derived from Sargassum spp. (biochar CSKPH). The CuNPs in biochar (CuNPs-CSKPH) did not appear in the XRD diffractograms, but the SEM-EDS results showed that they accounted for 36 % of the copper weight. The voltamperometric study of CuNps-CSKPH in acid media validated the presence of Cu and the amount was determined to be 2.58 µg. The catalytic activity of CuNPs-CSKPH was analyzed for the electrochemical reduction of CO2. The use of Sargassum spp. has great potential to tackle two environmental problems simultaneously, by using it as raw material for the synthesis of activated biochar as support, as well as the synthesis of CuNPs, and secondly, by using it as a sustainable material for the electrochemical conversion of CO2.

Growth of Anodic Layers on 304L Stainless Steel Using Fluoride Free Electrolytes and Their Electrochemical Behavior in Chloride Solution.

Anodic layers have been grown on 304L stainless steel (304L SS) using two kinds of fluoride-free organic electrolytes. The replacement of NH4F for NaAlO2 or Na2SiO3 in the glycerol solution and the influence of the H2O concentration have been examined. The obtained anodic layers were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and potentiodynamic polarization tests. Here, it was found that, although the anodic layers fabricated within the NaAlO2-electrolyte and high H2O concentrations presented limited adherence to the substrate, the anodizing in the Na2SiO3-electrolyte and low H2O concentrations allowed the growth oxide layers, and even a type of ordered morphology was observed. Furthermore, the electrochemical tests in chloride solution determined low chemical stability and active behavior of oxide layers grown in NaAlO2-electrolyte. In contrast, the corrosion resistance was improved approximately one order of magnitude compared to the non-anodized 304L SS substrate for the anodizing treatment in glycerol, 0.05 M Na2SiO3, and 1.7 vol% H2O at 20 mA/cm2 for 6 min. Thus, this anodizing condition offers insight into the sustainable growth of oxide layers with potential anti-corrosion properties.

Physicochemical and Optical Characterization of Citrus aurantium Derived Biochar for Solar Absorber Applications.

Agro-industrial waste valorization is an attractive approach that offers new alternatives to deal with shrinkage and residue problems. One of these approaches is the synthesis of advanced carbon materials. Current research has shown that citrus waste, mainly orange peel, can be a precursor for the synthesis of high-quality carbon materials for chemical adsorption and energy storage applications. A recent approach to the utilization of advanced carbon materials based on lignocellulosic biomass is their use in solar absorber coatings for solar-thermal applications. This study focused on the production of biochar from Citrus aurantium orange peel by a pyrolysis process at different temperatures. Biochars were characterized by SEM, elemental analysis, TGA-DSC, FTIR, DRX, Raman, and XPS spectroscopies. Optical properties such as diffuse reflectance in the UV-VIS-NIR region was also determined. Physical-chemical characterization revealed that the pyrolysis temperature had a negative effect in yield of biochars, whereas biochars with a higher carbon content, aromaticity, thermal stability, and structural order were produced as the temperature increased. Diffuse reflectance measurements revealed that it is possible to reduce the reflectance of the material by controlling its pyrolysis temperature, producing a material with physicochemical and optical properties that could be attractive for use as a pigment in solar absorber coatings.

Ceiba pentandra cellulose crosslinked with citric acid for drug release systems.

An alternative for the production of drug delivery system is proposed based on the Ceiba pentandra milkweed. The kapok cellulose was chemically crosslinked with citric acid (CA) at different CA proportions, and loaded with chlorhexidine diacetate (CHX) at different concentrations. Cellulose crosslinking was followed with FTIR and XPS analysis, and the CHX loading was determined using elemental analysis. In vitro studies showed a burst release within the first 2-3 h and the drug release kinetics was described with several models. In addition, the crosslinked Ceiba pentandra fibers did not exhibit a cytotoxic effect on human dermic fibroblasts. Results indicate that the crosslinked Ceiba pentandra fibers are a feasible material for the production of systems for drug release applications.