The Colloidal Properties of Nanocellulose.

Nanocelluloses are anisotropic nanoparticles of semicrystalline assemblies of glucan polymers. They have great potential as renewable building blocks in the materials platform of a more sustainable society. As a result, the research on nanocellulose has grown exponentially over the last decades. To fully utilize the properties of nanocelluloses, a fundamental understanding of their colloidal behavior is necessary. As elongated particles with dimensions in a critical nanosize range, their colloidal properties are complex, with several behaviors not covered by classical theories. In this comprehensive Review, we describe the most prominent colloidal behaviors of nanocellulose by combining experimental data and theoretical descriptions. We discuss the preparation and characterization of nanocellulose dispersions, how they form networks at low concentrations, how classical theories cannot describe their behavior, and how they interact with other colloids. We then show examples of how scientists can use this fundamental knowledge to control the assembly of nanocellulose into new materials with exceptional properties. We hope aspiring and established researchers will use this Review as a guide.

Nanoscale Assembly of Cellulose Nanocrystals during Drying and Redispersion.

We have followed the structural evolution during evaporation-induced self-assembly of sulfonated cellulose nanocrystal (CNC) in the presence of H+ and Li+ counterions by small-angle X-ray scattering. Drying of CNC-H dispersions results in ordered films that could not be readily redispersed, while the CNC-Li films were disordered and prone to reswelling and redispersion. The scaling of the separation distance (d) between CNC particles and the particle concentration (c) shows that the CNC-H dispersions display a unidimensional contraction of the nematic structure (d ∝ c-1) during drying, while the CNC-Li dispersions consolidate isotropically (d ∝ c-1/3), which is characteristic for hydrogels with no preferential orientation. Temporal evolution of the structure factor and complementary dynamic light-scattering measurements show that CNC-Li is more aggregated than CNC-H during evaporation-induced assembly. Insights on the structural evolution during CNC assembly and redispersion can promote development of novel and optimized processing routes of nanocellulose-based materials.

Directional Freezing of Nanocellulose Dispersions Aligns the Rod-Like Particles and Produces Low-Density and Robust Particle Networks.

We show that unidirectional freezing of nanocellulose dispersions produces cellular foams with high alignment of the rod-like nanoparticles in the freezing direction. Quantification of the alignment in the long direction of the tubular pores with X-ray diffraction shows high orientation of cellulose nanofibrils (CNF) and cellulose nanocrystals (CNC) at particle concentrations above 0.2 wt % (CNC) and 0.08 wt % (CNF). Aggregation of CNF by pH decrease or addition of salt significantly reduces the particle orientation; in contrast, exceeding the concentration where particles gel by mobility constraints had a relatively small effect on the orientation. The dense nanocellulose network formed by directional freezing was sufficiently strong to resist melting. The formed hydrogels were birefringent and displayed anisotropic laser diffraction patterns, suggesting preserved nanocellulose alignment and cellular structure. Nondirectional freezing of the hydrogels followed by sublimation generates foams with a pore structure and nanocellulose alignment resembling the structure of the initial directional freezing.

Stabilizing nanocellulose-nonionic surfactant composite foams by delayed Ca-induced gelation.

Aggregation of dispersed rod-like particles like nanocellulose can improve the strength and rigidity of percolated networks but may also have a detrimental effect on the foamability. However, it should be possible to improve the strength of nanocellulose foams by multivalent ion-induced aggregation if the aggregation occurs after the foam has been formed. Lightweight and highly porous foams based on TEMPO-mediated oxidized cellulose nanofibrils (CNF) were formulated with the addition of a non-ionic surfactant, pluronic P123, and CaCO3 nanoparticles. Foam volume measurements show that addition of the non-ionic surfactant generates wet CNF/P123 foams with a high foamability. Foam bubble size studies show that delayed Ca-induced aggregation of CNF by gluconic acid-triggered dissolution of the CaCO3 nanoparticles significantly improves the long-term stability of the wet composite foams. Drying the Ca-reinforced foam at 60 °C results in a moderate shrinkage and electron microscopy and X-ray tomography studies show that the pores became slightly oblate after drying but the overall microstructure and pore/foam bubble size distribution is preserved after drying. The elastic modulus (0.9-1.4 MPa) of Ca-reinforced composite foams with a density of 9-15 kg/m(3) is significantly higher than commercially available polyurethane foams used for thermal insulation.

Rod Packing in Chiral Nematic Cellulose Nanocrystal Dispersions Studied by Small-Angle X-ray Scattering and Laser Diffraction.

The packing of cellulose nanocrystals (CNC) in the anisotropic chiral nematic phase has been investigated over a wide concentration range by small-angle X-ray scattering (SAXS) and laser diffraction. The average separation distance between the CNCs and the average pitch of the chiral nematic phase have been determined over the entire isotropic-anisotropic biphasic region. The average separation distances range from 51 nm, at the onset of the anisotropic phase formation, to 25 nm above 6 vol % (fully liquid crystalline phase) whereas the average pitch varies from ≈15 µm down to ≈2 µm as ϕ increases from 2.5 up to 6.5 vol %. Using the cholesteric order, we determine that the twist angle between neighboring CNCs increases from about 1° up to 4° as ϕ increases from 2.5 up to 6.5 vol %. The dependence of the twisting on the volume fraction was related to the increase in the magnitude of the repulsive interactions between the charged rods as the average separation distance decreases.

Multicolor fluorescent labeling of cellulose nanofibrils by click chemistry.

We have chemically modified cellulose nanofibrils (CNF) with furan and maleimide groups, and selectively labeled the modified CNF with fluorescent probes; 7-mercapto-4-methylcoumarin and fluorescein diacetate 5-maleimide, through two specific click chemistry reactions: Diels-Alder cycloaddition and the thiol-Michael reaction. Characterization by solid-state (13)C NMR and infrared spectroscopy was used to follow the surface modification and estimate the substitution degrees. We demonstrate that the two luminescent dyes could be selectively labeled onto CNF, yielding a multicolor CNF that was characterized by UV/visible and fluorescence spectroscopies. It was demonstrated that the multicolor CNF could be imaged using a confocal laser scanning microscope.

Hydrodynamic alignment and assembly of nanofibrils resulting in strong cellulose filaments.

Cellulose nanofibrils can be obtained from trees and have considerable potential as a building block for biobased materials. In order to achieve good properties of these materials, the nanostructure must be controlled. Here we present a process combining hydrodynamic alignment with a dispersion-gel transition that produces homogeneous and smooth filaments from a low-concentration dispersion of cellulose nanofibrils in water. The preferential fibril orientation along the filament direction can be controlled by the process parameters. The specific ultimate strength is considerably higher than previously reported filaments made of cellulose nanofibrils. The strength is even in line with the strongest cellulose pulp fibres extracted from wood with the same degree of fibril alignment. Successful nanoscale alignment before gelation demands a proper separation of the timescales involved. Somewhat surprisingly, the device must not be too small if this is to be achieved.

Highly conducting, strong nanocomposites based on nanocellulose-assisted aqueous dispersions of single-wall carbon nanotubes.

It is challenging to obtain high-quality dispersions of single-wall nanotubes (SWNTs) in composite matrix materials, in order to reach the full potential of mechanical and electronic properties. The most widely used matrix materials are polymers, and the route to achieving high quality dispersions of SWNT is mainly chemical functionalization of the SWNT. This leads to increased cost, a loss of strength and lower conductivity. In addition full potential of colloidal self-assembly cannot be fully exploited in a polymer matrix. This may limit the possibilities for assembly of highly ordered structural nanocomposites. Here we show that nanofibrillated cellulose (NFC) can act as an excellent aqueous dispersion agent for as-prepared SWNTs, making possible low-cost exfoliation and purification of SWNTs with dispersion limits exceeding 40 wt %. The NFC:SWNT dispersion may also offer a cheap and sustainable alternative for molecular self-assembly of advanced composites. We demonstrate semitransparent conductive films, aerogels and anisotropic microscale fibers with nanoscale composite structure. The NFC:SWNT nanopaper shows increased strength at 3 wt % SWNT, reaching a modulus of 13.3 GPa, and a strength of 307 MPa. The anisotropic microfiber composites have maximum conductivities above 200 S cm(-1) and current densities reaching 1400 A cm(-2).

Colloidal stability of aqueous nanofibrillated cellulose dispersions.

Cellulose nanofibrils constitute an attractive raw material for carbon-neutral, biodegradable, nanostructured materials. Aqueous suspensions of these nanofibrils are stabilized by electrostatic repulsion arising from deprotonated carboxyl groups at the fibril surface. In the present work, a new model is developed for predicting colloidal stability by considering deprotonation and electrostatic screening. This model predicts the fibril-fibril interaction potential at a given pH in a given ionic strength environment. Experiments support the model predictions that aggregation is induced by decreasing the pH, thus reducing the surface charge, or by increasing the salt concentration. It is shown that the primary mechanism for aggregation upon the addition of salt is the surface charge reduction through specific interactions of counterions with the deprotonated carboxyl groups, and the screening effect of the salt is of secondary importance.