Health and Carcinogenic Risk Assessment of Exposure to by-Products of Photocatalytic Degradation of Toluene in a Spouted Bed Reactor with Porous and Non-Porous Draft Tube.

OBJECTIVE: This study was performed to assessment the health and carcinogenic risk of exposure to by-products of photocatalytic degradation of toluene in a spouted bed reactor Equipped with porous and non-porous draft tube. METHODS: For this purpose, titanium dioxide nanoparticles were used as photocatalysts and UV lamps as radiation sources. Degradation efficiency and CO2 selectivity were compared. By-products were also detected in three spouted bed reactors with and without a porous and non-porous draft tube. RESULT: The results revealed that the degradation efficiency of toluene in the spouted bed reactor without a draft tube was 30.75%. The insertion of porous and non-porous draft tubes in the spouted bed reactor increased the degradation efficiency up to 54.88% and 47.63%, respectively. Meantime, CO2 selectivity decreased from 100% to 50.8% within 180 min irradiation time in the spouted bed reactor without draft tube, while in the spouted bed reactors with porous and non-porous draft tube maintained at 89.85% and 84.35%, respectively. Toluene and four by-products with carcinogenic and non-carcinogenic risk of 0.002176 and 182.2, respectively, were detected in the spouted bed reactors without draft tube. However, no by-products with carcinogenic risk were found in the spouted bed reactor with porous and non-porous draft tube. CONCLUSION: photocatalytic degradation of toluene in a spouted bed reactor without a draft tube produces by-products with health and carcinogenic risks. The insertion of a porous and non-porous draft tube in spouted bed reactors provided mineralization more complete than spouted bed reactor without a draft tube by reducing the dead zone and providing appropriate contact between the toluene, photocatalyst, and UV. Therefore, prevent the formation of dangerous and carcinogenic by-products.

Preparation of Photocatalytic TiO2-Polyacrylonitrile Nanofibers for Filtration of Airborne Microorganisms.

Background: We aimed to investigate the efficiency of neat polyacrylonitrile (PAN) nanofibers and photocatalytic PAN/TiO2 nanofibers for removal of airborne microorganisms. Methods: Nanofibers were fabricated from 16 wt% of PAN dissolved in dimethyl formamide through the electrospinning technique. The efficiency of media for removal of Staphylococcus epidermidis and Bacillus subtilis was investigated at different conditions such as face velocity, relative humidity, air temperature and UVC radiation intensity. as face velocity (0.1 and 0.3 m/s), relative humidity (35±5% and 60±5%), air temperature (22±3 °C and 30±3 °C) and the UVC radiation intensity (dark, 1±0.09 mW/cm2 and 1.8±0.07 mW/cm2) using air sampling from upstream and downstream of media by cascade impactor containing blood agar culture medium. Results: The mean diameter of electrospun fibers and coefficient of variation were 194 nm and 15%, respectively. The amount of immobilized TiO2 on the filter was 620±6.56 mg/m2. Photocatalytic nanofiber filter media presented the best performance for removal of airborne B. subtilis at 60±5% relative humidity, 0.1 m/s face velocity, air temperature 22 °C, and 1.8 ± 0.07 mW/cm2 UVC radiation. Conclusion: The filtration efficiency of photocatalytic media was significantly higher than neat ones. Lower efficiency of media was found in the higher air velocity for all bioaerosols. High UVC radiation intensity increased filtration efficiency. Moreover, the increase in air temperature and relative humidity (except for TiO2-coated media under UVC radiation) did not significantly affect the filtration efficiency of all media.

UV protection properties of workwear fabrics coated with TiO2 nanoparticles.

The main purpose of this study was to evaluate the ultraviolet protective factor (UPF) of fabrics coated with TiO2 nanoparticles made using an in-situ synthesis method and more accurately assess the intrinsic properties of the textile. The cotton-polyester twill fabric (70-30%) (246.67 g/m2) was coated in-situ with TiO2 nanoparticles. In-situ coating is conducted in 4 steps; washing the fabrics, preparation of nanoparticles, injecting the nanoparticles into fabrics, and drying the fabric after coating. The scanning electron microscope (SEM) and X-ray diffraction (XRD), FTIR spectrometer, dynamic light scattering (DLS) and UV-Vis spectrophotometer were used to analyse the data of the coating and UPF results. Also, four standards such as ASTM D737, ISIRI 8332, ISIRI 4199, and ISIRI 567 were used for analyzing the intrinsic properties of a textile. The results of SEM, XRD and DLS altogether confirmed the in-situ formation of nanoparticles onto textile fibers. Moreover, the UPF value of the uncoated and coated fabrics was 3.67 and 55.82, respectively. It was shown that the in-situ deposition of TiO2 nanoparticles on fabric can provide adequate protection against UVR. Also, the results of analyzing the intrinsic properties of the textile showed that there were no significant differences in the intrinsic properties between the coated and uncoated fabrics. Based on the results, it can be concluded that the UV protective properties of workwear fabrics can be improved by coating TiO2 nanoparticles on them without any effect on the cooling effect of perspiration evaporation.

Effect of Co-exposure to Heat and Psychological Stressors on Sperm DNA and Semen Parameters.

The present study aims to investigate the effects of co-exposure to heat and psychological stress on sperm DNA and semen parameters among male rats. The study was conducted on 40 healthy adult male Wistar rats. The rats were randomly categorized into four groups of same size consisting of a control group, a heat stress, psychological and co-exposure groups. The heat stress group was exposed to a temperature of 36 °C at 20% relative humidity. The psychological stress exposure group was subjected to three stressors including exposure to strobe light, noise and tilting cage. According the results,the co-exposure group had lower mean sperm parameters including sperm count (17.22 ± 4.22 106/ml), motility (42.63 ± 12.95 %), viability (48.50 ± 23.25 %), normal morphology (56 ± 7.5%), progressive motility (11.61 ± 7.81%), non-progressive motility (31.18 ± 7.77%), curvilinear velocity (24.11 ± 3.81 µm/s) and straight-line velocity (3.2 ± 1.4 µm/s) when compared with those of the other groups (P = 0.001). Mean sperm immobility (57.36 ± 12.95%) and non-progressive motility (37.93 ± 11.15%) in the co-exposure group was higher compared to the other groups (P = 0.001 and P = 0.333, respectively). Assessment of damage to sperm DNA revealed that the heat exposure group had a higher percentage of sperm DNA damage (9.44 ± 6.80 %) compared to others (P = 0.185). In case of all of exposure scenario, the chance that the semen quality decreased compared to the control group has been increased. In general the combined stress had a greater significant effect on sperm parameters compared to other exposure groups, except for DNA damage.

The effects of combined exposure to road traffic noise and whole body vibration on types of attention among men.

BACKGROUND: Noise and vibration are considered as harmful physical agents in the environment which have adverse effects on cognitive performance. One of the occupations at risk is driving, where there is a possibility of simultaneous exposure to road traffic noise and whole body vibration (WBV) transferred through the vehicle. This study aims to assess the effects of single and combined exposure to road traffic noise and WBV on different types of attention in men. METHODS: The experiment was conducted on 24 men in 4 steps, executed on each participant inside an acoustic room. After recording a number of various attention scores at background conditions (27 dBA noise, no vibration) the participants were given single and combined exposure to noise levels at 55 and 85 dBA and vibration frequencies of 0.65 and 0.95 m/s2. RESULTS: As for combined exposure to noise and vibration, increasing vibration acceleration and noise levels at the same time compared to background condition caused a rise in the score of all visual attention types among groups exposed to low vibration acceleration and those exposed to medium acceleration and low noise. Nevertheless, when noise level and vibration acceleration is increased at the same time compared to background, auditory attention type scores mostly fell among groups with similar vibration accelerations. CONCLUSIONS: Overall, single and combined exposure to environmental stressors under investigation had a predominantly negative effect on auditory attention while the effects on visual attention were inconclusive. Definitive conclusions however require further systematic and comprehensive experiments.

Comprehensive analysis and investigation of accident/occupational disease responsibility rates: A case study for accidental CO poisoning.

One of the major problems of courts and insurance companies is the lack of a proper technique to determine the rate of responsibility of the parties involved in the accident. The aim of this study was to determine the Accident/Occupational Diseases Responsibility Rates (AOD RR) for complex events. Accordingly, a case study of a complex accident of carbon monoxide (CO) poisoning was selected and Occupational Accident Tree Analysis (OATA) and Occupational Accident Component Analysis (OACA) techniques, which were solely used to investigate occupational accidents, were used with the new names Accident/Occupational Disease Tree Analysis (AOD TA) and Accident/Occupational Disease Component Analysis (AOD CA) to evaluate their applicability to investigate non-occupational accidents and occupational diseases. For this purpose, causes of CO penetration to victims' room was assessed using gas tracking methods. Finally, Fuzzy Accident/Occupational Disease Tree/Component Analysis (FAOD TA and FAOD CA) techniques were developed and used for determining AOD RR in fuzzy environment. The results showed that the AOD RR obtained by AOD TA and AOD CA based on the average of experts' personal opinions and consensus between experts, and AOD TA and AOD CA in a fuzzy environment were close to each other, with the power terminal and the power cable crossing route being the main routes of transmission and penetration of CO to the victims' room. Also, the owner, contractor, tenant, and serviceman were responsible for the CO poisoning of victims. It can be concluded that any hole, crack, or fission in the building can result in CO penetration to the individuals' living rooms, and gas tracking in early winter, especially in older buildings, plays a very significant role in preventing residents' poisoning. Further, due to the uncertainty of AOD TA and AOD CA techniques, it is recommended to use FAOD TA and FAOD CA techniques for increasing the accuracy of the results. This will enhance the court and insurance companies' trust in the opinions of accident investigation experts, decrease delays in the proceedings, and prevent any violation of the individual rights.

Modeling heat stress changes based on wet-bulb globe temperature in respect to global warming.

BACKGROUND: This ecological study aims to model the trend of changes in exposure of outdoor workers to heat stress in outdoors in the coming decades with the use of the Wet-Bulb Globe Temperature (WBGT), Hadley Coupled Atmosphere- Ocean General Circulation Model, version 3 (HADCM3), and Long Ashton Research Station Weather Generator (LARS-WG) in Tehran, Iran, considering the climate change and the global warming. METHODS: The hourly values of environmental parameters including minimum and maximum air temperature, relative humidity, precipitation and radiation related to Prakash , Shahriar and Damavand cities were obtained from the Meteorological Organization of Iran. These data were recorded during 1965 to 2015. The climate modeling was done for 2011-2030, 2046-2065, and 2080-2099. RESULTS: The minimum and maximum air temperatures in the different months of the year in the three studied cities show an increasing trend. Our finding shows that the WBGT will be increased by 2099. In Pakdasht, this index will be close to the danger zone in the coming years, especially in 2080-2099. CONCLUSIONS: All the results obtained indicate an increase in risk of heat stress in outdoor workplaces, given the global warming.

Toxic effects of subacute inhalation exposure to trichloroethylene on serum lipid profile, glucose and biochemical parameters in Sprague-Dawley rats.

The current study evaluated the inhalation toxicity of trichloroethylene (TCE) at 0, 10, 100, 250 and 400 ppm in Sprague-Dawley rats for 10 day period, because the subacute inhalation toxicity of TCE on serum lipid profile, glucose and some biochemical parameters has not been previously reported. TCE vapors were generated using the dynamic generation system based on evaporation method in the exposure chamber. On the basis of the results, mean serum low-density lipoprotein (LDL) and albumin (ALB) decreased significantly in all the groups exposed to TCE compared with the control group (p < .005), but there was a significant increase for parameters: fasting blood glucose (FBG) and alkaline phosphatase (ALP) (p < .005). Rats exposed to 400 ppm TCE showed a significant decrease in serum cholesterol (CHOL) and protein (Pr) compared with the control group (p < .005). A negative relationship was found between triglycerides (TG), very low density lipoprotein (VLDL), CHOL, LDL, Pr, ALB and urea levels and the subacute exposure to concentrations of TCE (R2 = -0.26, p < .05), but there was a direct correlation for parameters FBG, ALP and alanine aminotransferase (ALT) (R2 = 0.42, p < .05). In conclusion, studies with Sprague-Dawley rats demonstrated that subacute inhalation exposure to TCE (≥ 100 PPM) is associated with biochemical and lipotoxicity in the form of decreased serum ALB and LDL and raised ALP and glucose levels. The present study also provides additional evidence relating to decreased serum CHOL and Pr after subacute inhalation exposure to 400 ppm TCE.

Assessment of contrast perception of obstacles in a tunnel entrance.

Background: The purpose of this study was to assess the contrast perception of obstacles in a tunnel entrance which was placed in Ilam Province, Iran. Methods: An obstacle with the reflection coefficient of 20% was mounted at the entrance of thetunnel and then, the car was placed near the tunnel entrance and the intrinsic luminance of the road (Lr,intrinsic) and obstacle (Lo,intrinsic) were measured inside the car using the luminance meter. Results: Intrinsic luminance of obstacle and road at the entrance of the tunnel were measured as 41 and 17 cd/m2, respectively. The contrast perception of obstacle in deriver's eyes and in the safe stopping distance (SSD) from the tunnel entrance was determined as 2.79 cd/m2. At the entrance of the studied tunnel, the contrast perception of obstacles with the reflection coefficient of 20% was lower than the minimum contrast perception (28%) recommended by International Commission on Illumination. Conclusion: The main conclusion that can be drawn from it, is that this obstacle in the SSD from the tunnel entrance cannot be conceived by the drivers, which may lead to higher rate of road traffic crashes.

Evaluation of the Combined Effects of Heat and Lighting on the Level of Attention and Reaction Time: Climate Chamber Experiments in Iran.

Heat exposure and unsuitable lighting are two physical hazardous agents in many workplaces for which there are some evidences regarding their mental effects. The purpose of this study was to assess the combined effect of heat exposure and different lighting levels on the attention rate and reaction time in a climatic chamber. This study was conducted on 33 healthy students (17 M/16 F) with a mean (±SD) age of 22.1 ± 2.3 years. The attention and reaction time test were done by continuous performance test and the RT meter, respectively, in different exposure conditions including the dry temperatures (22°C and 37°C) and lighting levels (200, 500, and 1500 lux). Findings demonstrated that increase in heat and lighting level caused a decrease in average attention percentage and correct responses and increase in commission error, omission error, and response time (P < 0.05). The average of simple, diagnostic, two-color selective, and two-sound selective reaction times increased after combined exposure to heat and lighting (P < 0.05). The results of this study indicated that, in job task which requires using cognitive functions like attention, vigilance, concentration, cautiousness, and reaction time, the work environment must be optimized in terms of heat and lighting level.

Evaluation of potential biomarkers of exposure to crystalline silica: A case study in an insulator manufacturer.

The purpose of this study was to examine the potential determinants of serum neopterin, malondialdehyde (MDA), and erythrocyte glutathione (GSH) as potential markers of oxidative stress, resulting in cellular immune response to inhaled silica particles. This descriptive analytical study was conducted on two groups of exposed workers ( n = 55) and unexposed office workers ( n = 38) of an insulator manufacturing plant. The sampling of airborne silica in the breathing zone of participants was done on the basis of the National Institute for Occupational Safety and Health Method 7601. The blood samples were analyzed by high performance liquid chromatography to determine the level of serum neopterin. A ZellBio GmbH assay kit was used for the quantitative assays of GSH and MDA on the basis of the colorimetric assay. The results of this study show that the measurements of serum neopterin, MDA, and GSH can be considered as potential biological markers of silica exposure for undertaking further comprehensive studies in this area.

Safety Evaluation of the Lighting at the Entrance of a Very Long Road Tunnel: A Case Study in Ilam.

BACKGROUND: At the entrance of a tunnel, reflection of sunlight from the surrounding environment and a lack of adequate lighting usually cause some vision problems. The purpose of this study was to perform a safety evaluation of lighting on a very long road in Ilam, Iran. METHODS: The average luminance was measured using a luminance meter (model S3; Hagner, Solna, Sweden). A camera (model 108, 35-mm single-lens reflex; Yashica, Nagano, Japan) was used to take photographs of the safe stopping distance from the tunnel entrance. Equivalent luminance was determined according to the Holliday polar diagram. RESULTS: Considering the average luminance at the tunnel entrance (116.7 cd/m2) and using Adrian's equation, the safe level of lighting at the entrance of the tunnel was determined to be 0.7. CONCLUSION: A comparison between the results of the safe levels of lighting at the entrance of the tunnel and the De Boer scale showed that the phenomenon of black holes is created at the tunnel entrance. This may lead to a misadaptation of the drivers' eyes to the change in luminance level at the entrance of the tunnel, thereby increasing the risk of road accidents in this zone.

Pulmonary Functions and Health-Related Quality of Life among Silica-Exposed Workers.

BACKGROUND: This study aimed to investigate the pulmonary functions of silica-exposed workers and their health-related quality of life in an insulator manufacturing industry. MATERIALS AND METHODS: In this cross-sectional study, participants selected from the manufacturing unit (n = 127) constituted the exposed group and those from the administrative department (n = 30) constituted the unexposed group. All subjects were evaluated using personal air sampling of crystalline silica, pulmonary function tests, and a quality of life questionnaire (36-item short form health survey [SF-36]). RESULTS: The mean (SD) concentrations of crystalline silica were 0.507 (0.23) mg/m3 and 0.0116 (0.008) mg/m3 for the exposed and unexposed groups, respectively. All the pulmonary function indices and all the physical and mental health domains of the workers were significantly lower than those of the administrative clerks (p < 0.05). The silica concentration did not significantly correlate with the quality of life components and all the pulmonary function indices (p > 0.05), except for forced vital capacity (FVC) and forced expiratory volume in one second (FEV1) (p < 0.05). CONCLUSION: In conclusion, the workers exposed to higher levels of crystalline silica had lower values of pulmonary function indices and lower health-related quality of life; however, further follow-up studies are needed to confirm these findings.

Survey of discomfort glare from the headlamps of cars widely used in Iran.

OBJECTIVE: On 2-lane roads, discomfort glare can cause annoyance, discomfort, inconvenience, stress, and fatigue to drivers, posing a risk of accidents. The aim of this study is to evaluate discomfort glare from the headlamps of cars widely used in Iran. METHODS: The discomfort glare of new vehicles including Pride Saba model GTX, Pride Model 131SL, Samand Soren, Peugeot 405, Megane, and Peugeot Pars was examined at distances of 5 to 100 m at a background luminance of 50 cd/m2 (late twilight/early dawn lighting) and 1 cd/m2 (nighttime) using Schmidt-Clausen and Bindels model and de Boer's subjective scale. RESULTS: According to the de Boer scale, at a background luminance of 50 cd/m2, the discomfort glare for all studied vehicles was between 1.98 and 4.05 in high-beam mode and between 3.5 and 5.4 in low-beam mode. At a background luminance of 1 cd/m2, discomfort glare was between 0.41 and 2.48 in high-beam mode and between 1.93 and 3.84 in low-beam mode. In high-beam mode, the average levels of discomfort glare of these vehicles gradually increased when the distance between cars was reduced by up to about 20 m. In low-beam mode, there was no discomfort glare up to a vehicle distance of 40 m. In addition, at an angle of 1.15°-5.73° between the line of sight and light of vehicles in high-beam mode, the level of discomfort glare was increased, but at an angle of 5.73°-22.9° the level of discomfort glare was reduced. In low-beam mode at an angle of 2.86°-22.9°, the level of discomfort glare was almost identical. The results show that in high-beam mode and with a 100-m distance between vehicles as well as in low-beam mode at intervals of less than 40 m between cars, discomfort glare is created. CONCLUSION: It can be concluded that by providing solutions such as installing road lighting system, an increase in luminance of roads, separating or widening road lanes, increasing the lateral distance between vehicles, and increasing the angle between lighted vehicles and drivers can noticeably reduce discomfort glare.

The influence of occupational heat exposure on cognitive performance and blood level of stress hormones: a field study report.

INTRODUCTION: This article aimed to investigate the effect of heat stress on cognitive performance and the blood concentration of stress hormones among workers of a foundry plant. METHODS: Seventy workers within the exposed (35 people) and unexposed (35 people) groups were studied. The wet bulb globe temperature (WBGT) index was measured for heat stress assessment. The cognitive performance tests were conducted using the Stroop color word test (SCWT) before and during working hours. For the assessment of the serum level of cortisol and the plasma level of adrenaline and noradrenaline, blood samples were taken during working hours from both groups. RESULTS: Only for SCWT III was there a significant relationship between heat stress and test duration, error rate and reaction time. The laboratory test results revealed significantly higher concentrations of cortisol, adrenaline and noradrenaline in the exposed subjects than in the unexposed group. There existed a positive correlation between cortisol, adrenaline, noradrenaline and WBGT index and also test duration and reaction time of SCWT III, and number of errors of SCWT I, SCWT II and SCWT III during work. CONCLUSION: Heat stress can lead to an increase in the blood level of stress hormones, resulting in cognitive performance impairment.

Validating the Heat Stress Indices for Using In Heavy Work Activities in Hot and Dry Climates.

BACKGROUND: Necessity of evaluating heat stress in the workplace, require validation of indices and selection optimal index. The present study aimed to assess the precision and validity of some heat stress indices and select the optimum index for using in heavy work activities in hot and dry climates. METHODS: It carried out on 184 workers from 40 brick kilns workshops in the city of Qom, central Iran (as representative hot and dry climates). After reviewing the working process and evaluation the activity of workers and the type of work, environmental and physiological parameters according to standards recommended by International Organization for Standardization (ISO) including ISO 7243 and ISO 9886 were measured and indices were calculated. RESULTS: Workers engaged in indoor kiln experienced the highest values of natural wet temperature, dry temperature, globe temperature and relative humidity among studied sections (P<0.05). Indoor workplaces had the higher levels of all environmental parameters than outdoors (P=0.0001), except for air velocity. The wet-bulb globe temperature (WBGT) and heat stress index (HSI) indices had the highest correlation with other physiological parameters among the other heat stress indices. Relationship between WBGT index and carotid artery temperature (r=0.49), skin temperature (r=0.319), and oral temperature (r=0.203) was statistically significant (P=0.006). CONCLUSIONS: Since WBGT index, as the most applicable index for evaluating heat stress in workplaces is approved by ISO, and due to the positive features of WBGT such as ease of measurement and calculation, and with respect to some limitation in application of HSI; WBGT can be introduced as the most valid empirical index of heat stress in the brick workshops.

Evaluating Effects of Heat Stress on Cognitive Function among Workers in a Hot Industry.

BACKGROUND: Heat stress, as one of the most common occupational health problems, can impair operators' cognitive processes. The aim of this study was to evaluate the impact of thermal stress on cognitive function among workers in a hot industry. METHODS: In this cross-sectional study conducted in Malibel Saipa Company in 2013, workers were assigned into two groups: one group were exposed to heat stress (n=35), working in casting unit and the other group working in machining unit (n=35) with a normal air conditioning. Wet Bulb Globe Temperature was measured at three heights of ankle, abdomen, and head. In order to evaluate the effects of heat stress on attention and reaction time, Stroop tests 1, 2, and 3 were conducted before starting the work and during the work. RESULTS: A significant positive correlation was observed between WBGT and test duration (P=0.01) and reaction time of Stroop test 3 (P=0.047), and between number of errors in Stroop tests 1, 2, and 3, during the work (P= 0.001). Moreover, Stroop test 3 showed a significant higher score for both test duration and reaction time of workers in case group. CONCLUSION: RESULTS of the present study, conducted in a real work environment, confirmed the impairment of cognitive functions, including selective attention and reaction time, under heat stress conditions.