Unraveling the Role of Nickel Nanoparticles Functionalization in the Electronic Properties and Structural Features of 2D Black Phosphorene Exposed to Ambient Conditions.

Layered black phosphorus (BP) is endowed with peculiar chemico-physical properties that make it a highly promising candidate in the field of electronics. Nevertheless, as other 2D materials with atomic scale thickness, it suffers from easy degradation under ambient conditions. Herein, it is shown that the functionalization of BP with preformed and in situ grown Ni NPs, affects the electronic properties of the material. In particular, Ni functionalization performed in situ leads to a narrowing of the average BP band gap from 1.15 to 0.95 eV and to a marked shift in the conduction band maximum from -0.33 V to -0.07 V, which, in turn, improve the ambient stability. Structural studies carried out by XAS can well distinguish the two nanohybrids and reveal that once Ni NPs are grown on BP nanosheets, a Ni-P coordinative bond is formed, featuring a short Ni-P distance of 2.27 Å, which is not observed when preformed Ni NPs are immobilized on BP. Comparing the XANES and EXAFS spectra of fresh and aged samples of both nanohybrids, suggests that the interaction between Ni and P atoms results in a stabilization effect exerted via a dual electronic and redox mechanism, that infers a much superior ambient stability to BP, even if the surface functionalization is far to achieve a full coverage.

Oxidation of Ethanol to Acetic Acid by Supported PtCu Nanoparticles Stabilized by a Diamine Ligand.

Diamine-capped PtCu nanoparticles have been synthesized by the simultaneous reduction of the corresponding bis-imine metal complexes with hydrogen and supported onto a high-surface-area carbon. The obtained heterogeneous catalyst was tested in thermally conducted aerobic oxidation of ethanol to acetic acid in water as well as in the electrochemical oxidation of ethanol. Both types of catalyses mediated by the PtCu alloy confirmed a notable increase in catalytic activity compared to the pure Pt- and Cu-based counterparts due to a clear bimetallic effect.

Synthesis of 2D anatase TiO2 with highly reactive facets by fluorine-free topochemical conversion of 1T-TiS2 nanosheets.

Two-dimensional (2D) anatase titanium dioxide (TiO2) is expected to exhibit different properties as compared to anatase nanocrystallites, due to its highly reactive exposed facets. However, access to 2D anatase TiO2 is limited by the non-layered nature of the bulk crystal, which does not allow use of top-down chemical exfoliation. Large efforts have been dedicated to the growth of 2D anatase TiO2 with high reactive facets by bottom-up approaches, which relies on the use of harmful chemical reagents. Here, we demonstrate a novel fluorine-free strategy based on topochemical conversion of 2D 1T-TiS2 for the production of single crystalline 2D anatase TiO2, exposing the {001} facet on the top and bottom and {100} at the sides of the nanosheet. The exposure of these faces, with no additional defects or doping, gives rise to a significant activity enhancement in the hydrogen evolution reaction, as compared to commercially available Degussa P25 TiO2 nanoparticles. Because of the strong potential of TiO2 in many energy-based applications, our topochemical approach offers a low cost, green and mass scalable route for production of highly crystalline anatase TiO2 with well controlled and highly reactive exposed facets.

Waste Face Surgical Mask Transformation into Crude Oil and Nanostructured Electrocatalysts for Fuel Cells and Electrolyzers.

A novel route for the valorization of waste into valuable products was developed. Surgical masks commonly used for COVID 19 protection by stopping aerosol and droplets have been widely used, and their disposal is critical and often not properly pursued. This work intended to transform surgical masks into platinum group metal-free electrocatalysts for oxygen reduction reaction (ORR) and hydrogen evolution reaction (HER) as well as into crude oil. Surgical masks were subjected to controlled-temperature and -atmosphere pyrolysis, and the produced char was then converted into electrocatalysts by functionalizing it with metal phthalocyanine of interest. The electrocatalytic performance characterization towards ORR and HER was carried out highlighting promising activity. At different temperatures, condensable oil fractions were acquired and thoroughly analyzed. Transformation of waste surgical masks into electrocatalysts and crude oil can open new routes for the conversion of waste into valuable products within the core of the circular economy.

Electrochemical CO2 reduction in water at carbon cloth electrodes functionalized with a fac-Mn(apbpy)(CO)3Br complex.

The organometallic complex (fac-Mn(apbpy)(CO)3Br) (apbpy = 4-(4-aminophenyl)-2,2'-bipyridine) grafted electrochemically onto carbon cloth serves as an electrocatalyst in the aqueous reduction of CO2 to syngas. A faradaic efficiency of around 60% for CO and 40% for H2 at -1.35 V is achieved together with a productivity rate higher than 870 NlCO h-1 gMn-1 at turnover numbers of up to 33 200 during 10 hours of operation.

Energy and chemicals from the selective electrooxidation of renewable diols by organometallic fuel cells.

Organometallic fuel cells catalyze the selective electrooxidation of renewable diols, simultaneously providing high power densities and chemicals of industrial importance. It is shown that the unique organometallic complex [Rh(OTf)(trop2NH)(PPh3)] employed as molecular active site in an anode of an OMFC selectively oxidizes a number of renewable diols, such as ethylene glycol , 1,2-propanediol (1,2-P), 1,3-propanediol (1,3-P), and 1,4-butanediol (1,4-B) to their corresponding mono-carboxylates. The electrochemical performance of this molecular catalyst is discussed, with the aim to achieve cogeneration of electricity and valuable chemicals in a highly selective electrooxidation from diol precursors.

Electrooxidation of ethylene glycol and glycerol on Pd-(Ni-Zn)/C anodes in direct alcohol fuel cells.

The electrooxidation of ethylene glycol (EG) and glycerol (G) has been studied: in alkaline media, in passive as well as active direct ethylene glycol fuel cells (DEGFCs), and in direct glycerol fuel cells (DGFCs) containing Pd-(Ni-Zn)/C as an anode electrocatalyst, that is, Pd nanoparticles supported on a Ni-Zn phase. For comparison, an anode electrocatalyst containing Pd nanoparticles (Pd/C) has been also investigated. The oxidation of EG and G has primarily been investigated in half cells. The results obtained have highlighted the excellent electrocatalytic activity of Pd-(Ni-Zn)/C in terms of peak current density, which is as high as 3300 A g(Pd)(-1) for EG and 2150 A g(Pd)(-1) for G. Membrane-electrode assemblies (MEA) have been fabricated using Pd-(Ni-Zn)/C anodes, proprietary Fe-Co/C cathodes, and Tokuyama A-201 anion-exchange membranes. The MEA performance has been evaluated in either passive or active cells fed with aqueous solutions of 5 wt % EG and 5 wt % G. In view of the peak-power densities obtained in the temperature range from 20 to 80 °C, at Pd loadings as low as 1 mg cm(-2) at the anode, these results show that Pd-(Ni-Zn)/C can be classified amongst the best performing electrocatalysts ever reported for EG and G oxidation.

"Click" on tubes: a versatile approach towards multimodal functionalization of SWCNTs.

Organic functionalization of carbon nanotube sidewalls is a tool of primary importance in material science and nanotechnology, equally from a fundamental and an applicative point of view. Here, an efficient and versatile approach for the organic/organometallic functionalization of single-walled carbon nanotubes (SWCNTs) capable of imparting multimodality to these fundamental nanostructures, is described. Our strategy takes advantage of well-established Cu-mediated acetylene-azide coupling (CuAAC) reactions applied to phenylazido-functionalized SWCNTs for their convenient homo-/heterodecoration with a number of organic/organometallic frameworks, or mixtures thereof, bearing terminal acetylene pendant arms. Phenylazido-decorated SWCNTs were prepared by chemoselective arylation of the CNT sidewalls with diazonium salts under mild conditions, and subsequently used for the copper-mediated cycloaddition protocol in the presence of terminal acetylenes. The latter reaction was performed in one step by using either single acetylene derivatives or equimolar mixtures of terminal alkynes bearing either similar functional groups (masked with orthogonally cleavable protecting groups) or easily distinguishable functionalities (on the basis of complementary analytical/spectroscopic techniques). All materials and intermediates were characterized with respect to their most relevant aspects/properties by TEM microscopy, thermogravimetric analysis coupled with MS analysis of volatiles (TG-MS), elemental analysis, cyclic voltammetry (CV), Raman and UV/Vis spectroscopy. The functional loading and related chemical grafting of both primary amino- and ferrocene-decorated SWCNTs were spectroscopically (UV/Vis, Kaiser test) and electrochemically (CV) determined, respectively.

Energy efficiency enhancement of ethanol electrooxidation on Pd-CeO(2)/C in passive and active polymer electrolyte-membrane fuel cells.

Pd nanoparticles have been generated by performing an electroless procedure on a mixed ceria (CeO(2))/carbon black (Vulcan XC-72) support. The resulting material, Pd-CeO(2)/C, has been characterized by means of transmission electron microscopy (TEM), inductively coupled plasma atomic emission spectroscopy (ICP-AES), and X-ray diffraction (XRD) techniques. Electrodes coated with Pd-CeO(2)/C have been scrutinized for the oxidation of ethanol in alkaline media in half cells as well as in passive and active direct ethanol fuel cells (DEFCs). Membrane electrode assemblies have been fabricated using Pd-CeO(2)/C anodes, proprietary Fe-Co cathodes, and Tokuyama anion-exchange membranes. The monoplanar passive and active DEFCs have been fed with aqueous solutions of 10 wt% ethanol and 2 M KOH, supplying power densities as high as 66 mW cm(-2) at 25 °C and 140 mW cm(-2) at 80 °C. A comparison with a standard anode electrocatalyst containing Pd nanoparticles (Pd/C) has shown that, at even metal loading and experimental conditions, the energy released by the cells with the Pd-CeO(2)/C electrocatalyst is twice as much as that supplied by the cells with the Pd/C electrocatalyst. A cyclic voltammetry study has shown that the co-support ceria contributes to the remarkable decrease of the onset oxidation potential of ethanol. It is proposed that ceria promotes the formation at low potentials of species adsorbed on Pd, Pd(I)-OH(ads), that are responsible for ethanol oxidation.

Steric control on the redox chemistry of (η5-C9H7)2Yb(II)(THF)2 by 6-aryl substituted iminopyridines.

A steric control on the reductive capacity of ytterbocenes towards iminopyridine ligands is described. The reaction of (η(5)-C(9)H(7))(2)Yb(THF)(2) with a series of 6-organyl-2-(aldimino)pyridyl ligands (IPy) takes place with the replacement of two THF molecules by one IPy unit. In contrast to the rich reductive ytterbocene chemistry described in the presence of the unsubstituted (aldimino)pyridyl ligand, all 6-aryl substituted IPys scrutinized hereafter are involved into the metal coordination as neutral bidentate {N,N} or tridentate {N,N,S; N,N,O} ligands, with no changes of the metal oxidation state in the final complexes. A series of Yb(II) metallocene complexes of general formula (η(5)-C(9)H(7))(2)Yb(II)(η(2) or η(3))[2,6-(i)Pr(2)(C(6)H(3))N=CH(C(5)H(3)N)-6-R)] have been isolated and completely characterized. The stereo-electronic role of the aryl substituents in the IPy ligands on the ytterbocene redox chemistry has also been addressed.

Self-sustainable production of hydrogen, chemicals, and energy from renewable alcohols by electrocatalysis.

The selective and simultaneous production of hydrogen and chemicals from renewable alcohols, such as ethanol, glycerol, and ethylene glycol, can be accomplished by means of electrolyzers in which the anode electrocatalyst is appropriately designed to promote the partial and selective oxidation of the alcohol. In the electrolyzers described herein, the production of 1 kg of hydrogen from aqueous ethanol occurs with one-third the amount of energy required by a traditional H(2)/O(2) electrolyzer, by virtue of the much lower oxidation potential of ethanol to acetate vs. water to oxygen in alkaline media (E(0)=0.10 V vs. 1.23 V). The self-sustainability of H(2) production is ensured by the simultaneous production of 25 kg of potassium acetate for every kg of H(2), if the promoting co-electrolyte is KOH.

Ethanol oxidation on electrocatalysts obtained by spontaneous deposition of palladium onto nickel-zinc materials.

Ni-Zn and Ni-Zn-P alloys supported on Vulcan XC-72 are effective materials for the spontaneous deposition of palladium through redox transmetalation with Pd(IV) salts. The materials obtained, Pd-(Ni-Zn)/C and Pd-(Ni-Zn-P)/C, have been characterized by a variety of techniques. The analytical and spectroscopic data show that the surface of Pd-(Ni-Zn)/C and Pd-(Ni-Zn-P)/C contain very small, highly dispersed, and highly crystalline palladium clusters as well as single palladium sites, likely stabilized by interaction with oxygen atoms from Ni--O moieties. As a reference material, a nanostructured Pd/C material was prepared by reduction of an aqueous solution of PdCl(2)/HCl with ethylene glycol in the presence of Vulcan XC-72. In Pd/C, the Pd particles are larger, less dispersed, and much less crystalline. Glassy carbon electrodes coated with the Pd-(Ni-Zn)/C and Pd-(Ni-Zn-P)/C materials, containing very low Pd loadings (22-25 microg cm(-2)), were studied for the oxidation of ethanol in alkaline media in half cells and provided excellent results in terms of both specific current (as high as 3600 A g(Pd)(-1) at room temperature) and onset potential (as low as -0.6 V vs Ag/AgCl/KCl(sat)).