Simulation of Bullet Fragmentation and Penetration in Granular Media.

The aim of this work is to simulate the fragmentation of bullets impacted through granular media, in this case, sand. In order to validate the simulation, a group of experiments were conducted with the sand contained in two different box prototypes. The walls of the first box were constructed with fiberglass and the second with plywood. The prototypes were subjected to the impact force of bullets fired 15 m away from the box. After the shots, X-ray photographs were taken to observe the penetration depth. Transient numerical analyses were conducted to simulate these physical phenomena by using the smooth particle hydrodynamics (SPH) module of ANSYS® 2019 AUTODYN software. Advantageously, this module considers the granular media as a group of uniform particles capable of transferring kinetic energy during the elastic collision component of an impact. The experimental results demonstrated a reduction in the maximum bullet kinetic energy of 2750 J to 100 J in 0.8 ms. The numerical results compared with the X-ray photographs showed similar results demonstrating the capability of sand to dissipate kinetic energy and the fragmentation of the bullet caused at the moment of impact.

Analysis of the Extreme Equilibrium Conditions of an Internal Cavity Located Inside a Flat Metal Plate Subjected to an Internal Pressure p.

The influence of surface bulges and cavities within metals is an important metallurgical-mechanical problem that has not been fully solved and motivates multiple discussions. This is not only related to the generation of interfaces, but also to the distribution of alloying components and elements. In this study, Laplace's equation was used to develop a set of equations to describe these kinds of defects in plates, which arise during the development of metallurgical processes, and this can be used for the prediction of pipeline failures subjected to internal pressure. In addition, the stability conditions of a cavity under an internal pressure are analyzed. The developed method allows to identify the stress state in the generation of the cavity and its propagation. In addition to this, finite element analyses were carried out in order to show first the stress distribution around a cavity subjected to a series of theoretical operation conditions and second to show the crack growth on the tip of the cavity.

Transient Thermomechanical Simulation of 7075 Aluminum Contraction around a SiO2 Microparticle.

One important challenge that faces the metallurgic industry turns around the constant increment in the mechanical resistance of certain finished products. Metallurgic advantages can be obtained from the inclusion of microparticles in metallic materials, but this inclusion involves complex challenges as the internal stress distribution can be modified. In this work, the simulation of a cooling sequence in 7075 aluminum with a SiO2 microparticle is presented. Two models of two-dimensional (2D) type were constructed in ANSYS®2019 with circular and oval shape microparticles located inside the aluminum. Both models were subjected to the same thermomechanical transient analysis to compare the remaining stress distributions around the microparticles after the thermal load and to observe the effect of the geometrical shape. The results show remaining stresses increased in the oval model as a consequence of the geometrical shape modification. After applying a tension load in the analyzed specimens, shear stress concentrations were observed with a higher magnitude around the covertex of the oval shape. The results can be very useful for the creation of materials with controlled remnant stress located in specific or desired locations in the matrix.

Luminescent Properties of (004) Highly Oriented Cubic Zinc Blende ZnO Thin Films.

Photoluminescence properties of cubic zinc blende ZnO thin films grown on glass substrates prepared by the spray pyrolysis method are discussed. X-ray diffraction spectra show the crystalline wurtzite with preferential growth in the (002) orientation and a metastable cubic zinc blende phase highly oriented in the (004) direction. Raman measurements support the ZnO cubic modification growth of the films. Photoluminescence (PL) spectra of zinc blende films are characterized by a new PL band centerd at 2.70 eV, the blue emission, in addition there are two principal bands that are also found in hexagonal ZnO films with the peak positions at 2.83 eV and 2.35 eV. The origin of the 2.70 eV band can be attributed to transitions from Zn-interstitial to Zn-vacancies. It is also important to mention that the PL intensity of the 2.35 eV band of the zinc blende thin films is relatively higher than in the band present in hexagonal ZnO films, which means that zinc blende films have more oxygen vacancies, as was corroborated by means of the energy dispersion spectroscopy (EDS) measurements. PL spectra at 77 °K were measured and the 2.70 eV band was confirmed for the zinc blende films. Some PL bands of cubic films also appeared for the hexagonal phase, which is due, to a certain extent, to the similar ions stacking of both wurtzite and zinc blende symmetries.