A parametrical finite element analysis for functionally graded material overlay restoration.

The main cause of failure in bonded ceramic restorations is material fracture due to excessive stress concentration at the base of the prosthesis. The design of restorative functionally graded materials (FGM) could represent a major advance in dissipating mechanical stresses during occlusal contacts. The aim of this paper is to carry out a complete factorial design of finite element analyses to optimize a multilayer FGM introduced at the bottom of an overlay prosthesis. The number and thickness of layers vary within a spectrum compatible with ceramic shaping processes whereas Young's moduli variations are set in the range of dental tissues. For a 1.5-mm thick prosthesis, the optimal FGM configuration appears to be a 5 layers of 0.2 mm thickness with a linear distribution of Young's modulus from 30 to 70 GPa. This configuration was implemented in a 3D model of a restored tooth with realistic geometry to validate the proof-of-concept.

In vitro shear bond strength over zirconia and titanium alloy and degree of conversion of extraoral compared to intraoral self-adhesive resin cements.

OBJECTIVE: Evaluation of the Shear bond strength over zirconia and titanium alloy and degree of conversion of extraoral compared to intraoral self-adhesive resin cements. MATERIALS AND METHODS: Nine bonding protocols were carried out on zirconia 4Y-TZP and titanium alloy (Ti-6Al-4V). Seven resin cement (one extraoral and six intraoral) were tested in the shear bond strength test and the degree of conversion measurements. RESULTS: The significantly highest value was obtained for Monobond Plus + Multilink Hybrid Abutment, the extraoral resin cement for both titanium alloy (35.1 MPa) and zirconia (32.9 MPa). For each resin, significantly higher DC values were obtained for the dual-cure mode compared with the self-cure mode. Regardless of the cure mode, Nexus Universal reached the highest DC (78.4%). DISCUSSION/CONCLUSIONS: In this study, the extraoral self-curing resin cement showed the higher bond strength values on zirconia and titanium alloy when associated with a universal primer. Some intraoral dual-cure resin cements showed closed performances when used with universal primers. There is no direct correlation between the degree of conversion of the resin cement and the shear bond strength obtained on the prosthetic materials tested.

Chairside posterior cantilevered fixed partial denture: Case report.

The cantilevered fixed partial denture (CFPD) is gaining recognition as a sound method of replacing missing teeth in the posterior sector. The purpose of this case report is to demonstrate that this type of restoration can be performed in a single appointment. A 39-year-old patient presented herself to the dental department; she showed agenesis of the two first maxillary premolars with a totally closed mesio-distal gap and a recent loss of the 2 s maxillary premolars. This case report concerns the replacement of the upper left second premolar. The patient was treated with a mesial CFPD resting on an "onlay-like" retainer on the first molar and replacing the missing premolar with a cantilevered pontic. The dimensions of the connection's cross-section were maximized as much as possible (>20 mm2). The restoration was designed and produced using chairside CAD-CAM from a milled-reinforced glass-ceramic block (Emax CAD, Ivoclar Vivadent). The aesthetic and functional integration of the prosthesis was successful. The patient was examined at 11 months for a follow-up. At this early stage, satisfactory dental hygiene was observed, associated with a smooth prosthetic fit, no periodontal inflammation, normal probing, and no abnormal dental mobility.

Mechanical Properties of Fused Deposition Modeling of Polyetheretherketone (PEEK) and Interest for Dental Restorations: A Systematic Review.

The aim of this systematic review was to determine the optimal printing parameters for the producing of fused deposition modeling (FDM) 3D-printed polyetheretherketone (PEEK) elements with mechanical properties suitable for dental restorations. Indeed, the mechanical properties are a critical prerequisite for the study of other parameters, such as physical, aesthetic and biological properties. An exhaustive electronic search was carried out in the PubMed, Embase and Web of knowledge databases to gather all the studies evaluating the influence of the printing parameters on the obtained mechanical properties of FDM 3D-printed PEEK elements were selected. Initially, the search resulted in 614 eligible papers. Independent screenings of the abstracts were performed by two authors to identify the articles related to the question. Twenty-nine studies were selected, of which eleven were further excluded after reading of the full text, and finally, eighteen articles were included in this review. The studies were difficult to compare due to the variability of the printing parameters and the types of PEEK. However, it seems interesting to use a high infill rate, a high chamber temperature close to that of the printing temperature and a heat post-treatment to obtain 3D PEEK elements presenting properties adapted to use as dental restorations. The analysis of the available literature suggested that the properties of PEEK could make it an interesting material in dental restorations to be performed with FDM additive manufacturing.

Shear Bond Strength of a Direct Resin Composite to CAD-CAM Composite Blocks: Relative Contribution of Micromechanical and Chemical Block Surface Treatment.

This study aims to compare the shear bond strength (SBS) of a direct resin composite to CAD-CAM resin composite blocks treated with different surface treatments: micromechanical, chemical or a combination of both. Eight CAD-CAM resin composite blocks, namely Brilliant Crios, Cerasmart 270, Vita Enamic, Grandio block, Katana Avencia, Lava Ultimate, Tetric CAD and Shofu Block HC were chosen. The micromechanical surface treatment protocols tested were hydrofluoric acid, polyacrylic acid or sandblasting, and the chemical one was a universal primer. These treated CAD-CAM blocks were tested to determine the SBS of a light-curing composite resin Z100 bonded to their surface. Two-way ANOVA followed by Tukey's post hoc test was used to investigate the difference in SBS. Failures were analyzed by Fisher's exact test. Bonding interfaces were examined by scanning electron microscopy. The micromechanical surface treatments give the highest SBS values: sandblasting appears to be the most efficient procedure for dispersed filler composite blocks, while hydrofluoric acid etching is preferable for polymer-infiltrated ceramic network (PICN) blocks. The use of universal primer does not improve SBS values on dispersed filler composite blocks. For PICN blocks, the use of universal primer significantly increases SBS values when combined with hydrofluoric acid etching.

3D-printed protected face shields for health care workers in Covid-19 pandemic.

The coronavirus pandemic resulted in a shortage of protective equipment. To meet the request of eye-protecting devices, an interdisciplinary consortium involving practitioners, researchers, engineers and technicians developed and manufactured thousands of inexpensive 3D-printed face shields, inside hospital setting. This action leads to the concept of "concurrent, agile, and rapid engineering".

Commercially Available Fluoride-Releasing Restorative Materials: A Review and a Proposal for Classification.

Resin composite and glass ionomer cement (GIC) are the most commonly used dental materials to perform direct restorations. Both have specific characteristics that explain their popularity and their limits. More than 20 years ago, the first attempt (followed by others) to combine the advantages of these two families was performed with compomers, but it was not very successful. Recently, new formulations (also called 'smart materials') with claimed ion release properties have been proposed under different family names, but there are few studies on them and explanations of their chemistries. This comprehensive review aims to gather the compositions; the setting reactions; the mechanical, self-adhesive, and potential bulk-fill properties; and the ion release abilities of the large existing families of fluoride-releasing restorative materials and the new restorative materials to precisely describe their characteristics, their eventual bioactivities, and classify them for an improved understanding of these materials. Based on this work, the whole GIC family, including resin-modified and highly viscous formulations, was found to be bioactive. Cention N (Ivoclar Vivadent, AG, Schaan, Lietschentein) is the first commercially available bioactive resin composite.