RESUMO
2,5-Diphenyl-1,3,4-oxadiazole has been widely used as an acceptor portion of donor-acceptor fluorophores that exhibit thermally activated delayed fluorescence (TADF), but analogous 2-alkyl-5-phenyl-1,3,4-oxadiazoles have been much less widely investigated. Here the properties of carbazole-substituted 2-methyl-5-phenyl-1,3,4-oxadiazoles are compared to those of their 2,5-diphenyl analogues. The fluorescence of each of the former compounds is blue-shifted by ca. 50-100 meV relative to that in the latter, while similar estimated values of the singlet-triplet energy separation (ΔEST) are maintained. In particular, 2-methyl-5-(penta(9-carbazolyl)phenyl)-1,3,4-oxadiazole and 2-methyl-5-(penta(3,6-di-tert-butyl-9-carbazolyl)phenyl)-1,3,4-oxadiazole exhibit solution fluorescence maxima of 466 and 485 nm and estimated ΔEST values of 0.12 and 0.03 eV, respectively. In both cases the reverse intersystem crossing (RISC) rates inferred from their solution fluorescence behavior are over twice those of the corresponding 2-phenyl derivatives. Organic light-emitting diodes (OLEDs) in which the 2-methyl derivatives are used as emitters yield external quantum efficiency (EQE) values of up to 23%. OLEDs with 2-methyl-5-(penta(9-carbazolyl)phenyl)-1,3,4-oxadiazole and 2-methyl-5-(penta(3,6-di-tert-butyl-9-carbazolyl)phenyl)-1,3,4-oxadiazole emitters show reduced efficiency rolloff at high current densities relative to their 2-phenyl counterparts, the latter exhibiting an EQE of 16% at 1000 cd m-2.
RESUMO
Stretchable optoelectronics made of elastomeric semiconductors could enable the integration of intelligent systems with soft materials, such as those of the biological world. Organic semiconductors and photodiodes have been engineered to be elastomeric; however, for photodetector applications, it remains a challenge to identify an elastomeric bulk heterojunction (e-BHJ) photoactive layer that combines a low Young's modulus and a high strain at break that yields organic photodiodes with low electronic noise values and high photodetector performance. Here, a blend of an elastomer, a donor-like polymer, and an acceptor-like molecule yields a skin-like e-BHJ with a Young's modulus of a few megapascals, comparable to values of human tissues, and a high strain at break of 189%. Elastomeric organic photodiodes based on e-BHJ photoactive layers maintain low electronic noise current values in the tens of femtoamperes range and noise equivalent power values in the tens of picowatts range under at least 60% strain.
RESUMO
Molecular p-type electrical dopants have been proven useful to fine-tune the optoelectronic properties of bulk organic semiconductors and their interfaces. Here, the volume in polymer films and its role in solution-based electrical p-type doping using phosphomolybdic acid (PMA) are studied. The polymer film volume was controlled using two approaches. One is based on heating both the PMA solution and the film prior to immersion. The second is based on coating the polymer film with a liquid blend that contains the PMA solution and a swelling solvent. 31P NMR and FTIR experiments indicate that the Keggin structure appears to be preserved throughout the doping process. Results show that increasing the polymer volume facilitates the infiltration of the PMA Keggin structure, which results in an increased electrical p-type doping level.
RESUMO
Silicon photodiodes are the foundation of light-detection technology; yet their rigid structure and limited area scaling at low cost hamper their use in several emerging applications. A detailed methodology for the characterization of organic photodiodes based on polymeric bulk heterojunctions reveals the influence that charge-collecting electrodes have on the electronic noise at low frequency. The performance of optimized organic photodiodes is found to rival that of low-noise silicon photodiodes in all metrics within the visible spectral range, except response time, which is still video-rate compatible. Solution-processed organic photodiodes offer several design opportunities exemplified in a biometric monitoring application that uses ring-shaped, large-area, flexible, organic photodiodes with silicon-level performance.
RESUMO
Thermally activated delayed fluorescent (TADF) materials are advantageous as emitters in organic light-emitting diodes (OLEDs) due to their ability to utilize all excited states formed by charge recombination for light emission, potentially leading to 100% internal quantum efficiency. As in conventional fluorescent or phosphorescent OLEDs, TADF emitters are commonly doped at a relatively low concentration in a host matrix. However, increasing evidence suggests that balanced ambipolar transport properties and small aggregation-induced fluorescence quenching allow TADF emitters to be used alone in so-called host-free OLEDs. Here, we report host-free OLEDs in which the emissive layers (EMLs) consist solely of a yellow-green-emitting TADF compound, 5,5'-(2,3,5,6-tetra(carbazol-9-yl)-1,4-phenylene)bis(2-(4-( tert-butyl)phenyl)-1,3,4-oxadiazole), TCZPBOX. Devices with this host-free EML yield a maximum external quantum efficiency (EQE) of 21%, current efficacy (CE) of 73 cd/A, and power efficacy (PE) of 79 lm/W at a luminance of 10 cd/m2. At a high luminance of 10,000 cd/m2, a high EQE of 13% is maintained. A maximum luminance of 120,000 cd/m2 is reached at an applied voltage of 9.8 V. When TCZPBOX was doped in the host 2,6-di(carbazol-9-yl)-pyridine (PYD2) at 40 wt %, the device yielded a maximum EQE of 28%, CE of 94 cd/A, and PE of 100 lm/W at 10 cd/m2.
RESUMO
We report on two π-conjugated donor-acceptor-donor (D-A-D) molecules of amphiphilic nature, aiming to promote intermolecular ordering and carrier mobility in organic electronic devices. Diketopyrrolopyrrole was selected as the acceptor moiety that was disubstituted with nonpolar and polar functional groups, thereby providing the amphiphilic structures. This structural design resulted in materials with a strong intermolecular order in the solid state, which was confirmed by differential scanning calorimetry and polarized optical microscopy. Langmuir-Blodgett (LB) films of ordered mono- and multilayers were transferred onto glass and silicon substrates, with layer quality, coverage, and intermolecular order controlled by layer compression pressure on the LB trough. Organic field-effect transistors and organic photovoltaics devices with active layers consisting of the amphiphilic conjugated D-A-D-type molecules were constructed to demonstrate that the LB technique is an effective layer-by-layer deposition approach to fabricate self-assembled, ordered thin films.
RESUMO
Organic thin-film transistors (OTFTs) can be fabricated at moderate temperatures and through cost-effective solution-based processes on a wide range of low-cost flexible and deformable substrates. Although the charge mobility of state-of-the-art OTFTs is superior to that of amorphous silicon and approaches that of amorphous oxide thin-film transistors (TFTs), their operational stability generally remains inferior and a point of concern for their commercial deployment. We report on an exhaustive characterization of OTFTs with an ultrathin bilayer gate dielectric comprising the amorphous fluoropolymer CYTOP and an Al2O3:HfO2 nanolaminate. Threshold voltage shifts measured at room temperature over time periods up to 5.9 × 105 s do not vary monotonically and remain below 0.2 V in microcrystalline OTFTs (µc-OTFTs) with field-effect carrier mobility values up to 1.6 cm2 V-1 s-1. Modeling of these shifts as a function of time with a double stretched-exponential (DSE) function suggests that two compensating aging mechanisms are at play and responsible for this high stability. The measured threshold voltage shifts at temperatures up to 75°C represent at least a one-order-of-magnitude improvement in the operational stability over previous reports, bringing OTFT technologies to a performance level comparable to that reported in the scientific literature for other commercial TFTs technologies.
RESUMO
2-(4-(9,9-Dimethylacridin-10(9H)-yl)phenyl)-5-phenyl-1,3,4-oxadiazole has an energy difference between the lowest excited singlet and triplet states (ΔE ST) of ca. 0.24 eV. Introduction of two electronegative fluorine atoms onto the acceptor portion of the molecule to give 2-(4-(9,9-dimethylacridin-10(9H)-yl)-3,5-difluorophenyl)-5-phenyl-1,3,4-oxadiazole lowers the energy of the singlet emission with a negligible effect on the corresponding triplet energy, leading to a donor-acceptor compound with decreased ΔE ST of ca. 0.13 eV that displays thermally activated delayed fluorescence. Organic light-emitting diodes fabricated using the latter compound display high EQEmax of 21.9% at a luminance of 10 cd/m2 and sky-blue emission, however, they suffer from a large efficiency roll-off at increased luminance.
RESUMO
Solution-based electrical doping protocols may allow more versatility in the design of organic electronic devices; yet, controlling the diffusion of dopants in organic semiconductors and their stability has proven challenging. Here we present a solution-based approach for electrical p-doping of films of donor conjugated organic semiconductors and their blends with acceptors over a limited depth with a decay constant of 10-20 nm by post-process immersion into a polyoxometalate solution (phosphomolybdic acid, PMA) in nitromethane. PMA-doped films show increased electrical conductivity and work function, reduced solubility in the processing solvent, and improved photo-oxidative stability in air. This approach is applicable to a variety of organic semiconductors used in photovoltaics and field-effect transistors. PMA doping over a limited depth of bulk heterojunction polymeric films, in which amine-containing polymers were mixed in the solution used for film formation, enables single-layer organic photovoltaic devices, processed at room temperature, with power conversion efficiencies up to 5.9 ± 0.2% and stable performance on shelf-lifetime studies at 60 °C for at least 280 h.
RESUMO
Organometal halide perovskites have shown excellent optoelectronic properties and have been used to demonstrate a variety of semiconductor devices. Colorful solar cells are desirable for photovoltaic integration in buildings and other aesthetically appealing applications. However, the realization of colorful perovskite solar cells is challenging because of their broad and large absorption coefficient that commonly leads to cells with dark-brown colors. Herein, for the first time, we report a simple and efficient strategy to achieve colorful perovskite solar cells by using the transparent conducting polymer (poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate), PEDOT:PSS) as a top electrode and simultaneously as an spectrally selective antireflection coating. Vivid colors across the visible spectrum are attained by engineering optical interference effects among the transparent PEDOT:PSS polymer electrode, the hole-transporting layer and the perovskite layer. The colored perovskite solar cells display power conversion efficiency values from 12.8 to 15.1% (from red to blue) when illuminated from the FTO glass side and from 11.6 to 13.8% (from red to blue) when illuminated from the PEDOT:PSS side. The new approach provides an advanced solution for fabricating colorful perovskite solar cells with easy processing and high efficiency.
RESUMO
We report on top-gate OFETs with a bilayer gate dielectric comprising an Al2O3 /HfO2 nanolaminate layer grown by atomic layer deposition and an amorphous fluoro-polymer layer (CYTOP). Top-gate OFETs display average carrier mobility values of 0.9 ± 0.2 cm2/(V s) and threshold voltage values of -1.9 ± 0.5 V and high operational and environmental stability under different environmental conditions such as damp air at 50 °C (80% relative humidity) and prolonged immersion in water at a temperature up to 95 °C.
RESUMO
We report on the reduction of contact resistance in solution-processed TIPS-pentacene (6,13-bis(triisopropylsilylethynyl)pentacene) and PTAA (poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine]) top-gate bottom-contact organic field-effect transistors (OFETs) by using different contact-modification strategies. The study compares the contact resistance values in devices that comprise Au source/drain electrodes either treated with 2,3,4,5,6-pentafluorothiophenol (PFBT), or modified with an evaporated thin layer of the metal-organic molecular dopant molybdenum tris-[1,2-bis(trifluoromethyl)ethane-1,2-dithiolene] (Mo(tfd)3), or modified with a thin layer of the oxide MoO3. An improved performance is observed in devices modified with Mo(tfd)3 or MoO3 as compared to devices in which Au electrodes are modified with PFBT. We discuss the origin of the decrease in contact resistance in terms of increase of the work function of the modified Au electrodes, Fermi-level pinning effects, and decrease of bulk resistance by electrically doping the organic semiconductor films in the vicinity of the source/drain electrodes.
RESUMO
In this Research Article, the effect of two techniques for top-electrode deposition in organic photovoltaics (OPVs) cells with the configuration ITO/PEDOT:PSS/PTB7-Th:PC71BM/PFN/top-electrode is analyzed. One deposition was made by evaporation under high vacuum, meanwhile the other was carried out at normal room atmosphere; for the former, a double layer of Ca and the eutectic alloy Field's metal (FM) was thermally evaporated, while for the latter FM was deposited just by melting and dropping it on top of the delimited active area at temperatures about 90 °C. The average short-circuit photocurrent density, open circuit voltage and fill factor for devices with either Ca/FM (evaporated) or FM (by dripping) cathode, were very similar: around 13.20 mA/cm2, 840 mV, and 0.6, respectively. Average efficiency for devices with the mentioned evaporated cathode was of 6.4% (largest value 7.0%), meanwhile for devices with the cathode deposited by dripping, it was of 6.1% (largest value 6.5%). Morphological analysis, by atomic force microscopy on the surface of a FM electrode, detached from an OPV device, shows inhomogeneities and pinholes in its surface with an average roughness of 16 nm. OPV photocurrent was studied by means of laser beam induced current (LBIC), it showed that OPVs devices with FM top electrode exhibits an inhomogeneous response. An impedance analysis was also carried out and results were correlated with defects observed at the studied interface. In spite of the mentioned deficiencies at FM interface, overall PV performance of devices with this electrode highlights the convenience of using FM because of its easy, fast, and low-cost deposition (vacuum free) characteristics.
RESUMO
In the development of ultrabarrier films for packaging electronics, the effective water vapor transmission rate is a combination of permeation through pinhole defects and the intrinsic permeation through the actual barrier film. While it is possible to measure the effective permeation rate through barriers, it is important to develop a better understanding of the contribution from defects to the overall effective barrier performance. Here, we demonstrate a method to investigate independently defect-assisted permeation and intrinsic permeation rates by observing the degradation of a calcium layer encapsulated with a hybrid barrier film, that is, prepared using atomic layer deposition (ALD) and plasma enhanced deposition (PECVD). The results are rationalized using an analytical diffusion model to calculate the permeation rate as a function of spatial position within the barrier. It was observed that a barrier film consisting of a PECVD SiN(x) layer combined with an ALD Al2O3/HfO(x) nanolaminate resulted in a defect-assisted water vapor transmission rate (WVTR) of 4.84 × 10(-5) g/m(2) day and intrinsic WVTR of 1.41 × 10(-4) g/m(2) day at 50 °C/85% RH. Due to the low defect density of the tested barrier film, the defect-assisted WVTR was found to be three times lower than the intrinsic WVTR, and an effective (or total) WVTR value was 1.89 × 10(-4) g/m(2) day. Thus, improvements of the barrier performance should focus on reducing the number of defects while also improving the intrinsic barrier performance of the hybrid layer.
RESUMO
Poly[N-9'-heptadecanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (PCDTBT) is shown to be simultaneously cross-linked and p-doped when immersed into a phosphomolybdic acid solution, yielding conductive films with low solubility that can withstand the solution processing of subsequent photoactive layers. Such a modified PCDTBT film serves to improve hole collection and limit carrier recombination in organic solar cells.
Assuntos
Reagentes de Ligações Cruzadas/química , Molibdênio/química , Ácidos Fosfóricos/química , Polímeros/química , Semicondutores , Energia SolarRESUMO
The dimers of pentamethyliridocene and ruthenium pentamethylcyclopentadienyl mesitylene, (IrCp*Cp)2 and (RuCp*mes)2, respectively, are shown here to be effective solution-processable reagents for lowering the work functions of electrode materials; this approach is compared to the use of solution-deposited films of ethoxylated poly(ethylenimine) (PEIE). The work functions of indium tin oxide (ITO), zinc oxide, and gold electrodes can be reduced to 3.3-3.4 eV by immersion in a toluene solution of (IrCp*Cp)2; these values are similar to those that can be obtained by spin-coating a thin layer of PEIE onto the electrodes. The work-function reductions achieved using (IrCp*Cp)2 are primarily attributable to the interface dipoles associated with the formation of submonolayers of IrCp*Cp(+) cations on negatively charged substrates, which in turn result from redox reactions between the dimer and the electrode. The electrical properties of C60 diodes with dimer-modified ITO cathodes are similar to those of analogous devices with PEIE-modified ITO cathodes.
RESUMO
We report on the performance and the characterization of top-gate organic field-effect transistors (OFETs), comprising a bilayer gate dielectric of CYTOP/Al2O3 and a solution-processed semiconductor layer made of a blend of TIPS-pentacene:PTAA, fabricated on recyclable cellulose nanocrystal-glycerol (CNC/glycerol) substrates. These OFETs exhibit low operating voltage, low threshold voltage, an average field-effect mobility of 0.11 cm(2)/(V s), and good shelf and operational stability in ambient conditions. To improve the operational stability in ambient a passivation layer of Al2O3 is grown by atomic layer deposition (ALD) directly onto the CNC/glycerol substrates. This layer protects the organic semiconductor layer from moisture and other chemicals that can either permeate through or diffuse out of the substrate.
RESUMO
N,N'-Dihexyl-6,6'-dicyanoisoindigo, N,N'-didecyl-5,5',6,6'-tetracyanoisoindigo, N,N'-dihexyl-5,5',6,6'-tetracyanoisoindigo, and N,N'-dihexyl-5,5',6,6'-tetracyanothienoisoindigo have been synthesised in moderate yields by the reaction of corresponding di and tetrabromo species with CuCN, with microwave heating leading to higher yields and fewer side products for the tetrasubstituted species. Di- and tetracyano substitution anodically shifts the molecular reduction potential relative to the unsubstituted cores by ca. 0.4 and 0.8 V, respectively, with the resultant values for the tetracyano derivatives (-0.58 to -0.67 V vs. FeCp2(+/0)) suggesting the possibility of air-stable electron transport. All the synthesised cyano derivatives operate in n-channel OFETs, while the tetrabromothienoisoindigo derivative functions in a p-channel transistor. The tetracyanothienoisoindigo derivative exhibits the highest field-effect electron mobility values - up to 0.04 and 0.09 cm(2) V(-1) s(-1) in spin-coated and inkjet-printed devices respectively - and OFETs incorporating this compound have been shown to operate in air without significant degradation of their mobility values in the saturation regime.
RESUMO
Efficient organic photovoltaic cells (OPV) often contain highly reactive low-work-function calcium electron-collecting electrodes. In this work, efficient OPV are demonstrated in which calcium electrodes were avoided by depositing a thin layer of the amine-containing nonconjugated polymer, polyethylenimine (PEIE), between the photoactive organic semiconductor layer and stable metal electrodes such as aluminum, silver, or gold. Devices with structure ITO/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/poly(3-hexylthiophene):indene-C60-bis-adduct (P3HT:ICBA)/PEIE/Al demonstrated overall photovoltaic device performance comparable to devices containing calcium electron-collecting electrodes, ITO/PEDOT:PSS/P3HT:ICBA/Ca/Al, with open-circuit voltage of 775±6 mV, short-circuit current density of 9.1±0.5 mA cm(-2), fill factor of 0.65±0.01, and power conversion efficiency of 4.6±0.3%, averaged over 5 devices at 1 sun.