RESUMO
Structural and functional characteristics of the two core-shell resins Capto™ Core 400 and 700, which are useful for the flow-through purification of bioparticles such as viruses, viral vectors, and vaccines, are compared using bovine serum albumin (BSA) and thyroglobulin (Tg) as models for small and large protein contaminants. Both resins are agarose-based and contain an adsorbing core surrounded by an inert shell. Although shell thicknesses are comparable (3.6 and 4.2 µm for Capto Core 400 and 700, respectively), the two resins differ substantially in pore size (pore radii of 19 and 50 nm, respectively). Because of the smaller pores and higher surface area, the BSA binding capacity of Capto Core 400 is approximately double that of Capto Core 700. However, for the much larger Tg, the attainable capacity is substantially larger for Capto Core 700. Mass transfer in both resins is affected by diffusional resistances through the shell and within the adsorbing core. For BSA, core and shell effective pore diffusivities are about 0.25 × 10-7 and 0.6 × 10-7 cm2/s, respectively, for Capto Core 400, and about 1.6 × 10-7 and 2.6 × 10-7 cm2/s, respectively, for Capto Core 700. These values decrease dramatically for Tg to 0.022 × 10-7 and 0.088 × 10-7 cm2/s and to 0.13 × 10-7 and 0.59 × 10-7 cm2/s for Capto Core 400 and 700, respectively. Adsorbed Tg further hinders diffusion of BSA in both resins. Column measurements show that, despite the higher static capacity of Capto Core 400 for BSA, the dynamic binding capacity is greater for Capto Core 700 as a result of its faster kinetics. However, some of this advantage is lost if the feed is a mixture of BSA and Tg since, in this case, Tg binding leads to greater diffusional hindrance for BSA.
Assuntos
Resinas Sintéticas/química , Soroalbumina Bovina/isolamento & purificação , Tireoglobulina/isolamento & purificação , Adsorção , Animais , Bovinos , Dextranos/química , Difusão , Glucose/química , Cinética , Microscopia Confocal , Tamanho da PartículaRESUMO
Capto™ Core 700 is a core-shell chromatographic support with an adsorbing core contained within an inert shell layer designed to purify larger biomolecules and bioparticles in a flow-through mode. The present study aims to characterize the structure and functional properties of this resin using bovine serum albumin (BSA, Mr~65 kDa) and thyroglobulin (Tg, Mr~660 kDa) as model impurity proteins. The functionalized adsorbing core and the inert shell have the same fibrous structure typical of agarose-based beads. The resin average bead size is 90.7 µm with a range of 50-130 µm, the shell thickness is 4.18 µm with a range of 3-6 µm and a standard deviation of 0.55 µm, and the pore radius, obtained by inverse size exclusion chromatography, is 50.4 ± 1.3 nm. Both proteins present highly favorable binding isotherms with maximum binding capacities of 55 and 105 mg/mL of total bead volume for BSA and Tg, respectively. The addition of 500 mM NaCl reduces the binding capacity by less than 50%, showing the ability of the resin to operate at high salt conditions. For both proteins, the effective pore diffusivity in the core is smaller than in the shell due to additional hindrance by bound protein in the core area. Effective pore diffusivities values in the core are 1.6 × 10-7 and 0.16 × 10-7 cm2/s for BSA and Tg, respectively. The DBC10% at 2 min residence time are 24 and 2 mg/mL for BSA and Tg, respectively. This study provides qualitative and quantitative information about Capto™ Core 700 resin. This information could be used to predict and optimize the purification of large biomolecules and bioparticle in route to the establishment of more effective downstream processes.
Assuntos
Cromatografia em Gel/métodos , Tamanho da Partícula , Adsorção , Animais , Bovinos , Resinas Sintéticas/química , Soroalbumina Bovina/química , Temperatura , Tireoglobulina/químicaRESUMO
Complex adsorption kinetics behaviors of proteins in mixtures hampers chromatographic process development and complicates model-based prediction of separation. We investigated the adsorption characteristics of mixtures comprised of a larger protein (secretory immunoglobulins or thyroglobulin) and a smaller protein (serum albumin or green fluorescence protein) on the small-pore anion exchanger Q Sepharose FF. Confocal laser scanning microscopy measurements revealed that binding of the large protein was extremely slow and eventually stopped completely after the adsorption front penetrated just a few µm into the particle. Binding capacities after 24 h of incubation were nevertheless around 35 mg/mL of particle which is relatively high when considering that only a fraction of the particle was saturated, suggesting that locally-high bound protein concentrations are attained in a layer close to the particle surface. During mixture adsorption, the bound protein layer also significantly hindered diffusion of the smaller proteins into the particles resulting in about three times slower adsorption kinetics compared to single component adsorption. The combined effects of restricted diffusion and protein binding explain why flow-through purification of these mixtures with the small-pore resin Q Sepharose FF is effective under practical conditions. In this resin, diffusion of secretory immunoglobulins (or thyroglobulin) is restricted in the small pores so that despite their intrinsically greater affinity for the resin, much less binds compared to small proteins. Using the large-pore resin POROS 50 HQ results in faster transport, but also in more binding of secretory immunoglobulins (or thyroglobulin) compared to smaller protein impurities, preventing effective flow-through purification.