Anaerobic degradation of glycol ether-ethanol mixtures using EGSB and hybrid reactors: Performance comparison and ether cleavage pathway.

The anaerobic biodegradation of ethanol-glycol ether mixtures as 1-ethoxy-2-propanol (E2P) and 1-methoxy-2-propanol (M2P), widely used in printing facilities, was investigated by means of two laboratory-scale anaerobic bioreactors at 25oC: an expanded granular sludge bed (EGSB) reactor and an anaerobic hybrid reactor (AHR), which incorporated a packed bed to improve biomass retention. Despite AHR showed almost half of solid leakages compared to EGSB, both reactors obtained practically the same performance for the operating conditions studied with global removal efficiencies (REs) higher than 92% for organic loading rates (OLRs) as high as 54 kg of chemical oxygen demand (COD) m-3 d-1 (REs of 70% and 100% for OLRs of 10.6 and 8.3 kg COD m-3 d-1 for E2P and M2P, respectively). Identified byproducts allowed clarifying the anaerobic degradation pathways of these glycol ethers. Thus, this study shows that anaerobic scrubber can be a feasible treatment for printing emissions.

Aspen Plus process-simulation model: Producing biogas from VOC emissions in an anaerobic bioscrubber.

A process-simulation model for a novel process consisted of an anaerobic bioscrubber was developed in Aspen Plus®. A novel approach was performed to implement the anaerobic reactor in the simulation, enabling it to be connected to the scrubber. The model was calibrated and validated using data from an industrial prototype that converted air emissions polluted with volatile organic compounds with an average daily concentration of 1129 mgC Nm-3 into bioenergy for more than one year. The scrubber, which showed a removal efficiency within 83-93%, was successfully predicted with an average absolute relative error of 5.2 ±â€¯0.08% using an average height-to-theoretical-plate value of 1.05 ±â€¯0.08 m and 1.37 ±â€¯0.11 m for each of the two commercial packing materials used, respectively. The anaerobic reactor, which treated up to 24 kg of chemical oxygen demand m-3 d-1 with efficiencies of about 93%, was accurately simulated, both in effluent-stream characteristics and in the biogas stream. For example, the average absolute error between the experimental biogas production and the model values was 19.6 ±â€¯18.9%. The model proved its capability as a predictive tool and an aid in design, resulting in savings of time and money for practitioners. In addition, the approach proposed can be expanded to other bioprocesses that include unit operations.

Granulation and microbial community dynamics in the chitosan-supplemented anaerobic treatment of wastewater polluted with organic solvents.

The effect of chitosan on the development of granular sludge in upflow anaerobic sludge blanket reactors (UASB) when treating wastewater polluted with the organic solvents ethanol, ethyl acetate, and 1-ethoxy-2-propanol was evaluated. Three UASB reactors were operated for 219 days at ambient temperature with an organic loading rate (OLR) of between 0.3 kg COD m-3 d-1 and 20 kg COD m-3 d-1. One reactor was operated without the addition of chitosan, while the other two were operated with the addition of chitosan doses of 2.4 mg gVSS-1 two times. The three reactors were all able to treat the OLR tested with COD removal efficiencies greater than 90%. However, the time required to reach stable operation was considerably reduced in the chitosan-assisted reactors. The development of granules in the reactors with chitosan was accelerated and granules larger than 2000 µm were only observed in these reactors. In addition, these granules exhibited better physicochemical characteristics: the mean particle diameter (540 and 613 µm) was approximately two times greater than in the control reactor (300 µm), and the settling velocities exceeded 35 m h-1. The extracellular polymeric substances (EPS) in the reactors with the chitosan was found to be higher than in the control reactor. The protein-EPS content has been correlated with the granule size. The analyses of the microbial communities, performed through denaturing gradient gel electrophoresis and high-throughput sequencing, revealed that the syntrophic microorganisms belonging to genus Geobacter and the hydrogenotrophic methanogen Methanocorpusculum labreanum were predominant in the granules. Other methanogens like Methanosaeta species were found earlier in the chitosan-assisted reactors than in the control reactor.

Control of VOCs from printing press air emissions by anaerobic bioscrubber: Performance and microbial community of an on-site pilot unit.

A novel process consisted of an anaerobic bioscrubber was studied at the field scale for the removal of volatile organic compounds (VOCs) emitted from a printing press facility. The pilot unit worked under high fluctuating waste gas emissions containing ethanol, ethyl acetate, and 1-ethoxy-2-propanol as main pollutants, with airflows ranging between 184 and 1253 m3 h-1 and an average concentration of 1126 ± 470 mg-C Nm-3. Three scrubber configurations (cross-flow and vertical-flow packings and spray tower) were tested, and cross-flow packing was found to be the best one. For this packing, daily average values of VOC removal efficiency ranged between 83% and 93% for liquid to air volume ratios between 3.5·10-3 and 9.1·10-3. Biomass growth was prevented by periodical chemical cleaning; the average pressure drop was 165 Pa m-1. Rapid initiation of anaerobic degradation was achieved by using granular sludge from a brewery wastewater treatment plant. Despite the intermittent and fluctuating organic load, the expanded granular sludge bed reactor showed an excellent level of performance, reaching removal efficiencies of 93 ± 5% at 25.1 ± 3.2 °C, with biogas methane content of 94 ± 3% in volume. Volatile fatty acid concentration was as low as 200 mg acetic acid L-1 by treating daily average organic loads up to 3.0 kg COD h-1, equivalent to 24 kg COD m-3 bed d-1. The denaturing gradient gel electrophoresis (DGGE) results revealed the initial shift of the domains Archaea and Bacteria associated with the limitation of the carbon source to a few organic solvents. The Archaea domain was more sensitive, resulting in a drop of the Shannon index from 1.07 to 0.41 in the first 123 days. Among Archaea, the predominance of Methanosaeta persisted throughout the experimental period. The increase in the proportion of Methanospirillum and Methanobacterium sp. was linked to the spontaneous variations of operating temperature and load, respectively. Among Bacteria, high levels of ethanol degraders (Geobacter and Pelobacter sp.) were observed during the trial.

Removal of 2-butoxyethanol gaseous emissions by biotrickling filtration packed with polyurethane foam.

The removal of 2-butoxyethanol from gaseous emissions was studied using two biotrickling filters (BTF1 and BTF2) packed with polyurethane foam. Two different inoculum sources were used: a pure culture of Pseudomonas sp. BOE200 (BTF1) and activated sludge from a municipal wastewater treatment plant (BTF2). The bioreactors were operated at inlet loads (ILs) of 130 and 195 g m(-3) hour(-1) and at an empty bed residence time (EBRT) of 12.5s. Under an IL of ∼130 g m(-3) hour(-1), BTF1 presented higher elimination capacities (ECs) than BTF2, with average values of 106±7 and 68±8 g m(-3) hour(-1), respectively. However, differences in ECs between BTFs were decreased by reducing the irrigation intervals from 1 min every 12 min to 1 min every 2 hours in BTF2. Average values of EC were 111±25 and 90±7 g m(-3) hour(-1) for BTF1 and BTF2, respectively, when working at an IL of ∼195 g m(-3) hour(-1). Microbial analysis revealed a significant shift in the microbial community of BTF1 inoculated with Pseudomonas sp. BOE200. At the end of the experiment, the species Microbacterium sp., Chryseobacterium sp., Acinetobacter sp., Pseudomonas sp. and Mycobacterium sp. were detected. In BTF2 inoculated with activated sludge, the denaturing gradient gel electrophoresis (DGGE) technique showed a diverse microbial community including species that was able to use 2-butoxyethanol as its carbon source, such as Pseudomonas aeruginosa and Pseudomonas putida as representative species. Although BTF1 inoculated with Pseudomonas sp. BOE200 and higher gas velocity (probably greater gas/liquid mass transfer rate) showed a slight improvement in performance, the use of activated sludge as inoculum seems to be a more feasible option for the industrial application of this technology.

Anaerobic removal of 1-methoxy-2-propanol under ambient temperature in an EGSB reactor.

Two laboratory-scale expanded granular sludge bed (EGSB) reactors were operated at 18 and 25 °C, respectively, for the treatment of synthetic wastewater composed of ethanol and 1-methoxy-2-propanol (M2P) in a mass ratio of 4:1. Reactors were operated first with continuous wastewater supply and after with discontinuous substrate supply (5 days a week, 16 h a day) to simulate shift working conditions. Under continuous wastewater supply chemical oxygen demand (COD), removal efficiency higher than 95 % was achieved at the end of the trial applying organic loading rates (OLR) of 29 and 43 kg COD m(-3) day(-1) at 18 and 25 °C; thus, corresponding to M2P OLR of 6.4 and 9.3 kg COD m(-3) day(-1), respectively. During intermittent supply of substrate, good performance was recorded at both temperatures with an OLR of 30 kg COD m(-3) day(-1) (M2P OLR of 6.6 kg COD m(-3) day(-1)). After 56 h without substrate supply, a decline in methane yield of 15-30 % was observed due to the deactivation of the biomass. Specific methanogenic activity (SMA) assays were carried out at the end of the experiments. SMA values using 1-methoxy-2-propanol as substrate were 24.3 and 7.8 ml CH4 gVSS(-1) day(-1) at 25 °C and at 18 °C, respectively. This is the first attempt to investigate the removal of 1-methoxy-2-propanol by EGSB reactors.

Abatement of styrene waste gas emission by biofilter and biotrickling filter: comparison of packing materials and inoculation procedures.

The removal of styrene was studied using two biofilters packed with peat and coconut fibre (BF1-P and BF2-C, respectively) and one biotrickling filter (BTF) packed with plastic rings. Two inoculation procedures were applied: an enriched culture with strain Pseudomonas putida CECT 324 for BFs and activated sludge from a municipal wastewater treatment plant for the BTF. Inlet loads (ILs) between 10 and 45 g m(-3) h(-1) and empty bed residence times (EBRTs) from 30 to 120 s were applied. At inlet concentrations ranging between 200 and 400 mg Nm(-3), removal efficiencies between 70 % and 95 % were obtained in the three bioreactors. Maximum elimination capacities (ECs) of 81 and 39 g m(-3) h(-1) were obtained for the BF1-P and BF2-C, respectively (IL of 173 g m(-3) h(-1) and EBRT of 60 s in BF1-P; IL of 89 g m(-3) h(-1) and EBRT of 90 s in BF2-C). A maximum EC of 52 g m(-3) h(-1) was obtained for the BTF (IL of 116 g m(-3) h(-1), EBRT of 45 s). Problems regarding high pressure drop appeared in the peat BF, whereas drying episodes occurred in the coconut fibre BF. DGGE revealed that the pure culture used for BF inoculation was not detected by day 105. Although two different inoculation procedures were applied, similar styrene removal at the end of the experiments was observed. The use as inoculum of activated sludge from municipal wastewater treatment plant appears a more feasible option.

Control of VOC emissions from a flexographic printing facility using an industrial biotrickling filter.

The study of an industrial unit of biotrickling filter for the treatment of the exhaust gases of a flexographic facility was investigated over a 2-year period with the objective to meet the volatile organic compound (VOC) regulatory emission limits. Increasing the water flow rate from 2 to 40 m(3) h(-1) improved the performance of the process, meeting the VOC regulation when 40 m(3) h(-1) were used. An empty bed residence time (EBRT) of 36 s was used when the inlet air temperature was 18.7 °C, and an EBRT as low as 26 s was set when the inlet temperature was 26.8 °C. During this long-term operation, the pressure drop over the column of the bioreactor was completely controlled avoiding clogging problems and the system could perfectly handle the non-working periods without VOC emission, demonstrating its robustness and feasibility to treat the emission of the flexographic sector.

Influence of ground tire rubber on the transient loading response of a peat biofilter.

The effect of using ground tire rubber (GTR) as an adsorptive material in the removal of a 2:1:1 weight mixture of n-butyl acetate, toluene and m-xylene by using a peat biofilter under different intermittent conditions was investigated. The performance of two identical size biofilters, one packed with fibrous peat alone and the other with a 3:1 (vol) fibrous peat and GTR mixture, was examined for a period of four months. Partition coefficients of both materials were measured. Values of 53, 118 and 402 L kg(-1) were determined for n-butyl acetate, toluene and m-xylene in peat, respectively; and values of 40, 609 and 3035 L kg(-1) were measured for the same compounds in GTR. Intermittent load feeding of 16 h per day, 5 days per week working at an EBRT of 60 s and an inlet VOC concentration of 0.3 g C m(-1), resulted in removal efficiencies higher than 90% for both biofilters, indicating that the addition of GTR did not adversely affect the behavior of the bioreactor. Full removal of n-butyl acetate was obtained for both biofilters. GTR improved the removal of the aromatics in the first part of the biofilter, facilitating lower penetration of the toluene and m-xylene into the bed. A 31-day starvation period was applied and intermittent operation subsequently restarted. In both biofilters, high removal efficiencies after a re-acclimation period of two days were achieved. A shock loading test related to 1-h peaks of three- and four-fold increases in its baseline concentration (0.30 g C m(-3)) was applied in both biofilters. For the biofilter packed with the peat and GTR mixture, attenuation greater than 60% was observed in the maximum outlet concentration when compared to the biofilter packed with peat alone.

Biofiltration of ethylbenzene vapours: influence of the packing material.

In order to investigate suitable packing materials, a soil amendment composed of granular high mineralized peat (35% organic content) locally available has been evaluated as carrier material for biofiltration of volatile organic compounds in air by comparison with a fibrous peat (95% organic content). Both supports were tested to eliminate ethylbenzene from air streams in laboratory-scale reactors inoculated with a two-month conditioned culture. In pseudo-steady state operation, experiments at various ethylbenzene inlet loads (ILs) were carried out. Maximum elimination capacity of about 120 g m(-3) h(-1) for an IL of 135 g m(-3) h(-1) was obtained for the fibrous peat. The soil amendment reactor achieved a maximum elimination capacity of about 45 g m(-3) h(-1) for an inlet load of 55 g m(-3) h(-1). Ottengraf-van den Oever model was applied to the prediction of the performance of both biofilters. The influence of gas flow rate was also studied: the fibrous peat reactor kept near complete removal efficiency for empty bed residence times greater than 1 min. For the soil amendment reactor, an empty bed residence time greater than 2 min was needed to achieve adequate removal efficiency. Concentration profiles along the biofilter were also compared: elimination occurred in the whole fibrous peat biofilter, while in the soil amendment reactor the biodegradation only occurred in the first 65% part of the biofilter. Results indicated that soil amendment material, previously selected to increase the organic content, would have potential application as biofilter carrier to treat moderate VOC inlet loads.

Two distinct cell sources of H2O2 in the lignifying Zinnia elegans cell culture system.

The use of transdifferentiating Zinnia elegans mesophyll cells has proved useful in investigations of the process of xylem differentiation from cambial derivatives. Cultured mesophyll cells can be induced by external stimuli to proceed through temporally controlled developmental programs which conclude in the formation of single-cell-derived dead vascular tracheids and parenchyma-like elements. However, there is a gap in our knowledge concerning the role played by reactive oxygen species (O(2) (-) and H(2)O(2)) in the development of these vascular elements. In this study, we show by the following four independent and highly selective methods that transdifferentiating Z. elegans mesophyll cells are capable of producing reactive oxygen species: the 2,3-bis(2-methoxy-4-nitro-5-sulfophenyl)-2H-tetrazolium-5-carboxanilide (XTT) assay, which monitors O(2) (-) production, and the xylenol orange, 2,7-dichlorofluorescein diacetate, and CeCl(3) assays, which monitor H(2)O(2) production and localization. The joint use of these biochemical (XTT and xylenol orange) assays and cytochemical (2,7-dichlorofluorescein diacetate and CeCl(3)) probes revealed that transdifferentiating Z. elegans mesophyll cells do not show an oxidative burst but live in a strongly oxidative state during the entire culture period. In this state, H(2)O(2) is produced by both tracheary and parenchyma-like elements, the nonlignifying parenchyma-like cells acting quantitatively as the main source. The existence of these two sources of H(2)O(2) in this in vitro cell culture system may be especially relevant during the later stages of tracheary cell wall lignification, in which lignifying tracheary elements become hollow. In the case of differentiating tracheary elements, H(2)O(2) was located in the same place and at the same time as the onset of tracheary element lignification, i.e., at the primary cell wall during secondary thickening, supporting the view that the H(2)O(2) produced by this in vitro culture system is destined for use during lignin biosynthesis.

Fermentation of municipal primary sludge: effect of SRT and solids concentration on volatile fatty acid production.

Laboratory bench-scale experiments were conducted to investigate the performance of primary sludge fermentation for volatile fatty acids production. Primary sludges from two major wastewater treatment plants located in Valencia (Pinedo and Carraixet) were used. Experiments were performed at solids retention times between 4 and 10 days, and total volatile solids concentrations between 0.6% and 2.8%. Operation at two temperatures (20 degrees C and 30 degrees C) was also checked. Results indicated the importance of feed sludge characteristics on volatile fatty acids yields, being approximately double for the Carraixet wastewater treatment plant sludge than for the Pinedo plant. In both cases, higher volatile fatty acids yields were observed at higher total volatile solids concentrations. Solids retention times above 6 days scarcely improve volatile fatty acids yields, while experiments conducted at 4 days of solids retention times show an important decrease in volatile fatty acids yields. On raising temperature an increase in volatile fatty acids yields was observed, mainly due to an improvement in the hydrolysis of particulate organic matter.