RESUMO
Hafnium oxide films were deposited on sapphire and silicon (100) substrates using the DC reactive magnetron sputtering technique from a pure hafnium target at different discharge power levels. The influence of the cathode power on the chemical composition, morphology, crystallographic structure and optical properties of the films was investigated. X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX) and Fourier-transform infrared spectroscopy (FTIR) were employed to determine the chemical composition and bonding structure. In all cases, the films were found to be amorphous or nanocrystalline with increased crystalline content as the sputtering power was increased, according to XRD and FTIR. In addition, EDX showed that the films were oxygen-rich. The effect of power deposition on the surface topography and morphology of the films was studied using atomic force microscopy (AFM) and scanning electron microscopy (SEM). The AFM and SEM images revealed the emergence of mound morphologies as the cathode power was increased. These features are related to blistering effects probably due to the presence of stress and its promotion within the film thickness. Finally, the optical properties showed an average transmission of 80% in the visible range, and the refractive index determined by spectral ellipsometry (SE) was found to be in the range of 1.85-1.92, close to the reported bulk value. SE was also used to study the film porosity observed by SEM, which can be related to the oxygen-rich character of the films.
RESUMO
Bacteria grow on surfaces and form communities called biofilms. Bacterial adhesion and properties of the derived biofilms depend on, among others, the nature of the supporting substrate. Here, we report how the surface properties of the substrate affect the biofilm growth of probiotic Lactobacillus rhamnosus GG (LGG). Hydrophilic (OH), hydrophobic (CH3), and positively charged (NH3+) surfaces were obtained by the functionalization of a ZnSe crystal with alkanethiol self-assembled monolayers (SAM). The self-assembly of alkanethiols onto ZnSe was studied in situ using infrared spectroscopy in attenuated total reflection mode (ATR-FTIR). The organization of grafted SAMs was analyzed based on the results of ATR-FTIR, high-energy elastic backscattering spectrometry, and contact angle measurements. The kinetics and adhesion strength of LGG initial attachment as well as its physiological state on surfaces terminated by the different functional groups were assessed by the combination of ATR-FTIR, force measurements based on atomic force microscopy, and fluorescent staining of bacteria. The strength of interactions between LGG and the surface was strongly affected by the terminal group of the alkanethiol chain. The -NH3+ groups displayed the highest affinity with LGG at the first stage of interaction. The surface properties also played an important role when LGG biofilms were further grown in a nutritive medium for 24 h under flow conditions. Notably, the analysis of the infrared spectra recorded during the biofilm cultivation revealed differences in the kinetics of growth and in the polysaccharide features of the biofilm depending on the substrate functionality. LGG biofilm was stable only on the positively charged surface upon rinsing. Findings of this work clearly show that the adhesion features and the growth of LGG biofilms are substrate-dependent.
Assuntos
Biofilmes/crescimento & desenvolvimento , Lacticaseibacillus rhamnosus/fisiologia , Compostos de Selênio/química , Compostos de Zinco/química , Aderência Bacteriana/fisiologia , Interações Hidrofóbicas e Hidrofílicas , Cinética , Propriedades de SuperfícieRESUMO
We report the experimental observation of interrupted coarsening for surface self-organized nanostructuring by ion erosion. Analysis of the target surface by atomic force microscopy allows us to describe quantitatively this intriguing type of pattern dynamics through a continuum equation put forward in different contexts across a wide range of length scales. The ensuing predictions can thus be consistently extended to other experimental conditions in our system. Our results illustrate the occurrence of nonequilibrium systems in which pattern formation, coarsening, and kinetic roughening appear, each of these behaviors being associated with its own spatiotemporal range.
RESUMO
An increasing amount of effort is currently being directed towards the development of new functionalized nanostructured materials (i.e., multilayers and nanocomposites). Using an appropriate combination of composition and microstructure, it is possible to optimize and tailor the final properties of the material to its final application. The analytical characterization of these new complex nanostructures requires high-resolution analytical techniques that are able to provide information about surface and depth composition at the nanometric level. In this work, we comparatively review the state of the art in four different depth-profiling characterization techniques: Rutherford backscattering spectroscopy (RBS), secondary ion mass spectrometry (SIMS), X-ray photoelectron spectroscopy (XPS) and glow discharge optical emission spectroscopy (GDOES). In addition, we predict future trends in these techniques regarding improvements in their depth resolutions. Subnanometric resolution can now be achieved in RBS using magnetic spectrometry systems. In SIMS, the use of rotating sample holders and oxygen flooding during analysis as well as the optimization of floating low-energy ion guns to lower the impact energy of the primary ions improves the depth resolution of the technique. Angle-resolved XPS provides a very powerful and nondestructive technique for obtaining depth profiling and chemical information within the range of a few monolayers. Finally, the application of mathematical tools (deconvolution algorithms and a depth-profiling model), pulsed sources and surface plasma cleaning procedures is expected to greatly improve GDOES depth resolution.
RESUMO
A compact portable vacuum-compatible chamber designed for surface X-ray scattering measurements on beamline ID01 of the European Synchrotron Radiation Facility, Grenoble, is described. The chamber is versatile and can be used for in situ investigation of various systems, such as surfaces, nanostructures, thin films etc., using a variety of X-ray-based techniques such as reflectivity, grazing-incidence small-angle scattering and diffraction. It has been conceived for the study of morphology and structure of semiconductor surfaces during ion beam erosion, but it is also used for the study of surface oxidation or thin film growth under ultra-high-vacuum conditions. Coherent X-ray beam experiments are also possible. The chamber is described in detail, and examples of its use are given.
RESUMO
We study the self-organized ordering of nanostructures produced by ion-beam sputtering of targets amorphizing under irradiation. By introducing a model akin to models of pattern formation in aeolian sand dunes, we extend consistently the current continuum theory of erosion by IBS. We obtain new nonlinear effects responsible for the in-plane ordering of the structures, whose strength correlates with the degree of ordering found in experiments. Our results highlight the importance of redeposition and surface viscous flow to this nanopattern formation process.
RESUMO
The design of reproducible and more efficient nanofabrication routes has become a very active research field in recent years. In particular, the development of new methods for micro- and nanopatterning materials surfaces has attracted the attention of many researchers in industry and academia as a consequence of the growing relevance of patterned surfaces in many technological fields, ranging from optoelectronics to biotechnology. In this work we explore, discuss, and demonstrate the possibility of extending the well-known molding and replication strategy for patterning ceramic materials with nanoscale resolution. To achieve this goal we have combined physical deposition methods, molecule-thick anti-sticking coatings, and nanostructured substrates as master surfaces. This new perspective on an "old technology", as molding is, provides an interesting alternative for high-resolution, direct surface-relief patterning of materials that currently requires expensive and time-consuming lithographic approaches.