High-density dependence but low impact on selected reproduction parameters of Brucella suis biovar 2 in wild boar hunting estates from South-Western Spain.

Porcine brucellosis is a disease caused by Brucella suis, which is characterized by reproductive disorders in pigs. The number of cases of swine brucellosis has risen in many European countries, likely because of the presence of a wild reservoir of B. suis in wild boar. This study aimed at evaluating factors that may influence the probability of infection with Brucella spp. in wild boar and at assessing the impact of a previous contact with Brucella spp. on reproductive parameters of wild boar. Two hundred and four wild boar living in Extremadura (south-western Spain) were studied. The presence of anti-Brucella antibodies was determined using an indirect ELISA, while the presence of living bacteria in genital organs was evaluated through microbiological cultures. Sex, age, density of wild boar in summer and presence of outdoor pigs were selected as possible risk factors for being seropositive for Brucella spp. in wild boar. In addition, reproductive parameters such as breeding status or potential fertility in females and testis weight in males were estimated and related to the presence of anti-Brucella antibodies. A total of 121 animals were seropositive, resulting in a prevalence of 59.3% (95% CI). In addition, seven isolates of B. suis biovar 2 were obtained. Wild boar density in summer, as well as age and sex, was proposed as factors to explain the probability of Brucella seroconversion, although wild boar density in summer was the key factor. Current measures of reproductive parameters were not influenced by a previous contact with Brucella spp. Isolation of B. suis confirms that wild boar could represent a risk to domestic pig health in the study area. Wild boar density seems to have a great influence in the probability of infections with B. suis and suggests that density management could be useful to control Brucella infection in wild boar.

Outbreak of swine erysipelas in a semi-intensive wild boar farm in Spain.

Swine erysipelas (SE) is a disease caused by the bacterium Erysipelothrix rhusiopathiae and is one of the best-known and most serious diseases affecting domestic pigs. However, few studies exist concerning the susceptibility of wild boars to this disease and the role of this species as a reservoir. This study investigates and describes an outbreak of SE that occurred on a semi-intensive wild boar breeding farm housing 40 boars in Extremadura (SW Spain) on 11-18 February 2010. Seven animals died, of which four were examined post-mortem. Of these, three (two females and one male) were approximately 3 months old, and one was 1 year old (male). Lesions were consistent with acute septicaemia, consisting of cutaneous erythema/cyanosis and petechial haemorrhages in kidneys, urinary bladder, lungs and meninges. The 1-year-old male also had proliferative polyarthritis. Histopathology confirmed the presence of disseminated intravascular coagulation and vasculitis. Additionally, a bilateral acute panuveitis with concurrent necrotizing vasculitis and diffuse corneal oedema, neither of which have been described before in this disease, were found in the 3-month-old male boar. E. rhusiopathiae was isolated from all four animals in pure cultures from several tissues. Of these four animals, antibodies against E. rhusiopathiae, using an indirect ELISA test, were only detected in the 1-year-old male boar with polyarthritis. Posteriorly, of nine live adults tested for antibodies, four (including an adult male with polyarthritis) were positive.

Scanning electron microscope study of scalers.

Scanning electron microscopy was used to examine factory-sharpened, dulled, and resharpened scalers. The following observations were made: 1. The factory sharpened scalers exhibited metallic extensions from the lateral surface (wire edges). 2. The machine-resharpened instruments resulted in nonfunctional wire edges from the facial surface. Honing produced an exact meeting of facial and lateral surfaces. 3. Hand sharpening, using an Arkansas stone (grit 500) against the lateral surface away from the cutting edge, effected an exact meeting of the facial and lateral surfaces and no evidence of wire edges. 4. From this study an optimum cutting edge for a scaler is characterized as having a smooth, contiguous meeting of the facial and lateral surfaces free of wire edges. If a wire edge is present, it should be functional.