Comparison of the different methods of width estimation in unerupted canine and premolars.

BACKGROUND: There are different methods for determining the required space for unerupted teeth. However, the accuracy of these techniques varies depending on ethnic differences. Therefore, the current study was performed to compare the accuracy of four methods for estimating the mesiodistal width of unerupted canines and premolars in a population of northern Iran. METHODS: The present cross-sectional study was conducted on 50 pairs of dental casts of patients aged 12-24 years old. The mesiodistal width of the teeth was measured with a digital caliper by two observers (ICC < 0.9), and the mean value was recorded. The space required for eruption of canines and premolars was obtained by the Tanaka-Johnson formula and the Moyers tables and compared with the actual value by paired t test. RESULTS: The Tanaka-Johnson formula had overestimation in the maxilla and mandible, which was statistically significant (p < 0.001). The values obtained from the Moyers tables in different confidence levels were not accurate. However, the 65% level for the mandible had almost no difference from the actual value (P = 0.996 and r2 = 0.503). Furthermore, linear regression was obtained based on the total mesiodistal width of the maxillary first molar and mandibular central incisor (maxilla: Yx= 0.613X + 2.23 and mandible: Ym= 0.618X + 1.6) and the total mesiodistal width of the mandibular first molar and maxillary central incisor in each jaw (maxilla: Yx = 0.424X + 5.021 and mandible: Ym = 0.447X + 3.631). CONCLUSION: The Tanaka-Johnson method was overestimated in the population of northern Iran. The 85% and 75% confidence levels of the Moyers table have the best clinical results for the maxilla and mandible, respectively. Regression based on maxillary first molars and mandibular central incisors has better results.

Efficacy of quercetin flavonoid in recovering the postbleaching bond strength of orthodontic brackets: A preliminary study.

OBJECTIVES: To evaluate comparatively the effect of quercetin on postbleaching shear bond strength (SBS) and adhesive remnant index (ARI). MATERIALS AND METHODS: Intact maxillary premolars were divided randomly into 12 groups of 10 each: (1) bonding the bracket immediately after bleaching, (2) bonding 1 week after bleaching, (3-8) application of three experimental concentrations of quercetin (0.1%, 0.5%, and 1%) at two time durations (5 and 10 min), (9-10) application of the solvent of quercetin at two time periods (5 and 10 min), (11) application of 10% sodium ascorbate for 10 min, and (12) bonding the brackets on nonbleached teeth. Bleaching was performed using 15% carbamide peroxide gel for 5 days (6 h daily). After incubation and thermocycling, the SBS of brackets was measured. The ARI too was recorded at ×20. The data were analyzed statistically (α =0.05). RESULTS: Bleaching reduced the SBS below 10 Megapascal (MPa) level (P < 0.05) while all the postbleaching treatments (except the application of the solvent of quercetin) recovered the SBS back to values greater than 10 MPa (P < 0.05) and also back to nonbleached SBS levels (P > 0.01). All eight postbleaching treatments had rather similar efficacies (P = 0.1396). The concentration of quercetin (beta = 0.259, P = 0.042) but not its duration (beta = 0.213, P = 0.093) significantly improved its efficacy. CONCLUSION: Bleaching can weaken the bond strength of orthodontic brackets below acceptable levels. The application of quercetin or Vitamin C or delaying the bracket bonding improved the postbleaching SBS.

Antimicrobial effect, frictional resistance, and surface roughness of stainless steel orthodontic brackets coated with nanofilms of silver and titanium oxide: a preliminary study.

Nano-silver and nano-titanium oxide films can be coated over brackets in order to reduce bacterial aggregation and friction. However, their antimicrobial efficacy, surface roughness, and frictional resistance are not assessed before. Fifty-five stainless-steel brackets were divided into 5 groups of 11 brackets each: uncoated brackets, brackets coated with 60 µm silver, 100 µm silver, 60 µm titanium, and 100 µm titanium. Coating was performed using physical vapor deposition method. For friction test, three brackets from each group were randomly selected and tested. For scanning electron microscopy and atomic-force microscopy assessments, one and one brackets were selected from each group. For antibacterial assessment, six brackets were selected from each group. Of them, three were immediately subjected to direct contact with S. mutans. Colonies were counted 3, 6, 24, and 48 h of contact. The other three were stored in water for 3 months. Then were subjected to a similar direct contact test. Results pertaining to both subgroups were combined. Groups were compared statistically. Mean (SD) friction values of the groups 'control, silver-60, silver-100, titanium-60, and titanium-100' were 0.55 ± 0.14, 0.77 ± 0.08, 0.82 ± 0.11, 1.52 ± 0.24, and 1.57 ± 0.41 N, respectively (p = .0004, Kruskal-Wallis). Titanium frictions were significantly greater than control (p < .05), but silver groups were not (p > .05, Dunn). In the uncoated group, colony count increased exponentially within 48 h. The coated groups showed significant reductions in colony count (p < .05, two-way-repeated-measures ANOVA). In conclusions, all four explained coatings reduce surface roughness and bacterial growth. Nano-titanium films are not suitable for friction reduction. Nano-silver results were not conclusive and need future larger studies.