Miniaturized 3D-Printed Cell Enables Water/Ethanol Quantification Using Electrochemical Impedance Spectroscopy.

A miniaturized and low-cost electrochemical 3D-printed system for rapid and accurate quantification of ethanol content in ethanol fuel using electrochemical impedance spectroscopy (EIS) was developed. The monolithic design of the system incorporates insulating thermoplastic electrode separators, with only the cover being mobile, allowing for easy assembly and handling. The portable device, measuring approximately 26 × 24 mm, has a maximum capacity of 1 mL, making it suitable for lab-on-a-chip and portable analysis. By utilizing the dielectric constant of ethanol and ethanol fuel mixtures with water, the miniaturized EIS cell quantifies ethanol content effectively. To validate its performance, we compared measurements from four gas stations with a digital densimeter, and the values obtained from the proposed system matched perfectly. Our miniaturized and low-cost electrochemical 3D-printed device can be printed and assembled in two hours, offering a cost-effective solution for fast and precise ethanol quantification. Its versatility, affordability, and compatibility with lab-on-a-chip platforms make it easily applicable, including for fuel quality control and on-site analysis in remote locations.

Portland Cement/Acrocomia Aculeata Endocarp Bricks: Thermal Insulation and Mechanical Properties.

In the last few decades, Portland/residue composites have been researched due to their technological and environmental advantages. In this study, residues of Acrocomia aculeata (Jacq.) Lodd endocarp (AE) were introduced in the Portland cement-soil (PC) matrix in different concentrations (0, 5, 10, 15, 20, and 50 wt%) to produce PC/AE bricks. The characterization of the microstructures of the bricks indicate agglomerates of AE particles with increased humidity in small regions distributed throughout the matrix. Mid-infrared and laser-induced breakdown spectroscopy, along with thermogravimetry, indicated that AE contained mainly lignin and cellulose, as well as inorganic chemical elements such as Mg and Si. X-ray studies revealed that AE did not affect the crystallographic properties of the Portland/AE bricks. The findings indicate that the use of AE improved the thermal insulation capability of the composites with a small impact on the compressive strength.

Screening charged impurities and lifting the orbital degeneracy in graphene by populating Landau levels.

We report the observation of an isolated charged impurity in graphene and present direct evidence of the close connection between the screening properties of a 2D electron system and the influence of the impurity on its electronic environment. Using scanning tunneling microscopy and Landau level spectroscopy, we demonstrate that in the presence of a magnetic field the strength of the impurity can be tuned by controlling the occupation of Landau-level states with a gate voltage. At low occupation the impurity is screened, becoming essentially invisible. Screening diminishes as states are filled until, for fully occupied Landau levels, the unscreened impurity significantly perturbs the spectrum in its vicinity. In this regime we report the first observation of Landau-level splitting into discrete states due to lifting the orbital degeneracy.

Asymmetric effect of oxygen adsorption on electron and hole mobilities in bilayer graphene: long- and short-range scattering mechanisms.

We probe electron and hole mobilities in bilayer graphene under exposure to molecular oxygen. We find that the adsorbed oxygen reduces electron mobilities and increases hole mobilities in a reversible and activated process. Our experimental results indicate that hole mobilities increase due to the screening of long-range scatterers by oxygen molecules trapped between the graphene and the substrate. First principle calculations show that oxygen molecules induce resonant states close to the charge neutrality point. Electron coupling with such resonant states reduces the electron mobilities, causing a strong asymmetry between electron and hole transport. Our work demonstrates the importance of short-range scattering due to adsorbed species in the electronic transport in bilayer graphene on SiO2 substrates.

Fabrication of gas nanosensors and microsensors via local anodic oxidation.

A nanosensor and microsensor fabrication method employing scanning probe microscopy (SPM) is demonstrated. Within such process, nano- or microscale metal oxide (MoO(x) or TiO(x)) structures, constituting the active region of a sensor, are directly fabricated onto a microscopic metal track via SPM-assisted local anodic oxidation (LAO). Two distinct LAO routes, a slow (conventional) or a fast (unusual) one, are employed to produce nano- and microsensors, which are tested at different temperatures using CO2 and H2 as test gases. Sensitivities down to ppm levels are demonstrated, and the possibility of easy integration into microfabrication processes is also discussed.