Formation of Microcapsules of Pullulan by Emulsion Template Mechanism: Evaluation as Vitamin C Delivery Systems.

Pullulan is a polysaccharide that has attracted the attention of scientists in recent times as a former of edible films. On the other hand, its use for the preparation of hydrogels needs more study, as well as the formation of pullulan microcapsules as active ingredient release systems for the food industry. Due to the slow gelation kinetics of pullulan with sodium trimetaphosphate (STMP), capsules cannot be formed through the conventional method of dropping into a solution of the gelling agent, as with other polysaccharides, since the pullulan chains migrate to the medium before the capsules can form by gelation. Pullulan microcapsules have been obtained by using inverse water-in-oil emulsions as templates. The emulsion that acts as a template has been characterized by monitoring its stability and by optical microscopy, and the size of the emulsion droplets has been correlated with the size of the microcapsules obtained, demonstrating that it is a good technique for their production. Although some flocs of droplets form, these remain dispersed during the gelation process and two capsule size distributions are obtained: those of the non-flocculated droplets and the flocculated droplets. The microcapsules have been evaluated as vitamin C release systems, showing zero-order release kinetics for acidic pH and Fickian mechanism for neutral pH. On the other hand, the microcapsules offer good protection of vitamin C against oxidation during an evaluation period of 14 days.

Rheological Study of the Formation of Pullulan Hydrogels and Their Use as Carvacrol-Loaded Nanoemulsion Delivery Systems.

Hydrogels have been extensively studied as delivery systems for lipophilic compounds. Pullulan hydrogels were prepared, and their gelation kinetics were studied over time. Pullulan exhibited a relatively slow gelling reaction in basic medium (KOH) using trisodium metaphosphate (STMP) as a cross-linking agent, so capsules cannot be obtained by dripping as easily as in the case of alginate and chitosan. The kinetics of pullulan gelation were studied through rheological analysis over time. An optimal [Pullulan]/[KOH] ratio was found for a fixed [Pullulan]/[STMP] ratio. For this given relationship, gelling time measurements indicated that when the concentration of pullulan increased, the gelation time decreased from 60 min for 6% w/w pullulan to 10 min for 10% w/w. After the gel point, a hardening of the hydrogel was observed over the next 5 h. The formed hydrogels presented high degrees of swelling (up to 1800%). Freeze-dried gels were capable of being rehydrated, obtaining gels with rheological characteristics and visual appearance similar to fresh gels, which makes them ideal to be freeze-dried for storage and rehydrated when needed. The behavior of the hydrogels obtained as active ingredient release systems was studied. In this case, the chosen molecule was carvacrol (the main component of oregano oil). As carvacrol is hydrophobic, it was incorporated into the droplets of an oil-in-water nanoemulsion, and the nanoemulsion was incorporated into the hydrogel. The release of the oil was studied at different pHs. It was observed that as the pH increased (from pH 2 to pH 7), the released amount of carvacrol for the gel with pullulan 10% w/w reached 100%; for the other cases, the cumulative release amount was lower. It was attributed to two opposite phenomena in the porous structure of the hydrogel, where more porosity implied a faster release of carvacrol but also a higher degree of swelling that promoted a higher entry of water flow in the opposite direction. This flow of water prevented the active principle from spreading to the release medium.

Study of nanoemulsions using carvacrol/MCT-(Oleic acid-potassium oleate)/ Tween 80 ®- water system by low energy method.

Carvacrol is studied in different fields due to its microbial and antioxidant properties. Its use is limited because of the water insolubility and its strong taste. To overcome these problems, carvacrol has been successfully loaded into nanoemulsions. The low-energy emulsification method Phase Inversion Composition (PIC) is used to prepare oil-in-water nanoemulsions in the carvacrol/medium chain triglycerides (MCT)-(oleic acid-potassium oleate/Tween 80 ®)-water system. Oleic acid acts as a co-surfactant when it is neutralized with KOH along the emulsification path changing the spontaneous curvature of the interface when increasing the HLB number from 1 for the oleic acid to 20 for the potassium oleate and, therefore, changing the HLB number of the surfactant mixture. The phases diagrams are studied in order to understand the behaviour of the system and to establish the composition range where nanoemulsions can be obtained. Nanoemulsions are formed when the emulsification path crosses a region of direct or planar structure without excess of oil. Experimental design is performed in order to study the influence of composition variables as carvacrol/MCT ratio and (oleic-oleate)/Tween 80 ® ratio (OL-OT/T80 ratio) on the diameter of the nanoemulsions and their stability. It has been observed the importance of the HLB number of the surfactants mixture in order to obtain small-sized stable nanoemulsions. Surface response graphic shows that (OL-OT)/T80 ratio is a significant parameter in the mean diameter of the nanoemulsions. A minimum diameter is obtained for a (OL-OT)/T80 ratio 45/55 due to the fact that ratio is near the preferred HLB of the oil mixture and the emulsification path contains a wide liquid crystal monophasic region with all the oil incorporated in the structure. Diameters of 19 nm for carvacrol/MCT ratio of 30/70 or diameters of 30 nm for ratios of 45/55 with high stability values presented a good potential to be incorporated into edible films in the future. Regarding nanoemulsions stability an optimum value is also observed for a carvacrol/MCT ratio. The addition of another carrier oil as olive oil instead of MCT showed an improvement of the nanoemulsions stability against Ostwald ripening, probably due to the smaller solubility of olive oil. The use of olive oil does not significantly change the diameter of the nanoemulsion.

The folliculin-FNIP1 pathway deleted in human Birt-Hogg-Dubé syndrome is required for murine B-cell development.

Birt-Hogg-Dubé (BHD) syndrome is an autosomal dominant disorder characterized by cutaneous fibrofolliculomas, pulmonary cysts, and kidney malignancies. Affected individuals carry germ line mutations in folliculin (FLCN), a tumor suppressor gene that becomes biallelically inactivated in kidney tumors by second-hit mutations. Similar to other factors implicated in kidney cancer, FLCN has been shown to modulate activation of mammalian target of rapamycin (mTOR). However, its precise in vivo function is largely unknown because germ line deletion of Flcn results in early embryonic lethality in animal models. Here, we describe mice deficient in the newly characterized folliculin-interacting protein 1 (Fnip1). In contrast to Flcn, Fnip1(-/-) mice develop normally, are not susceptible to kidney neoplasia, but display a striking pro-B cell block that is entirely independent of mTOR activity. We show that this developmental arrest results from rapid caspase-induced pre-B cell death, and that a Bcl2 transgene reconstitutes mature B-cell populations, respectively. We also demonstrate that conditional deletion of Flcn recapitulates the pro-B cell arrest of Fnip1(-/-) mice. Our studies thus demonstrate that the FLCN-FNIP complex deregulated in BHD syndrome is absolutely required for B-cell differentiation, and that it functions through both mTOR-dependent and independent pathways.