Noise-induced hearing loss in the military dental setting: a UK legislative perspective.

INTRODUCTION: Health professionals working in the dental environment are potentially at risk of noise-induced hearing loss (NIHL) due to the use of clinical and laboratory equipment. Workplaces engaging in the practice of dentistry within the UK are subject to legislation from the Control of Noise at Work (CNW) regulations 2005. Clinicians working in the military are at further increased risk of NIHL due to exposure from additional risk factors such as rifles or aircraft engines. To our knowledge, no authors have previously studied the noise levels experienced in a military dental setting or compared noise levels in a typical dental practice with current UK legislation. METHOD: Measurements of noise levels experienced by a dentist, dental nurse and dental hygienist during a standard conservation procedure were assessed using wearable noise dose-badges. Furthermore, noise levels within a dental technician's work space were also assessed. Noise levels produced by representative clinical and laboratory equipment were assessed and compared with CNW legislation. RESULTS: The highest level for clinical equipment was produced by the suction apparatus while aspirating up a cup of water at 76 dB. For laboratory equipment, the lower exposure action value (LEAV) of 80 dB would be exceeded in 2.1 hours' use of the trimmer, 3.6 hours' use of the vibrating table and 9 min use of the airline. CONCLUSIONS: Noise levels experienced by clinicians within the dental surgery were well below the legislative LEAV thresholds for both peak and continuous noise. However, noise levels produced by laboratory equipment were far higher and there is clearly the potential for excessive noise exposure for dental professional in the everyday setting. Dental professionals responsible for dental laboratory settings must be familiar with the CNW regulations and measures put in place that control the inadvertent breach of legislation. Hearing protection must be mandated when using equipment that exceeds the LEAV and an educational programme is required to explain both their correct use and the rationale behind it. Methods of mitigating that risk further require exploration such as alternative methods of completing the tasks performed by the airline or reducing the noise generated by it, such as by reducing the supply pressure or using an alternative nozzle design.

Managing a nosocomial outbreak of carbapenem-resistant Klebsiella pneumoniae: an early Australian hospital experience.

BACKGROUND: Carbapenems are traditionally reserved as the last line of defence for treatment of serious infections with multiresistant Gram-negative bacilli. Reports of Klebsiella pneumoniae carbapenemase (KPC)-producing organisms have been emerging globally, but rare in Australasia to date. We describe an outbreak of KPC-2 producing K. pneumoniae at an Australian hospital. METHODS: After initial detection in October 2012, a retrospective review of patients with meropenem-resistant K. pneumoniae to June 2012, and ongoing prospective surveillance, was undertaken. Included patients were admitted to the hospital after June 2012 and had meropenem-resistant K. pneumoniae isolated from any site. Available isolates underwent detection of the KPC-2 gene by polymerase chain reaction and molecular typing was performed to determine genetic relatedness between isolates. Point-prevalence screening was performed on selected wards to detect asymptomatic carriage. Infection control procedures were implemented to contain the outbreak. RESULTS: Ten cases were identified in the initial cluster. Eight were localised to a single inpatient ward. Point-prevalence screening revealed one extra case. After temporary containment, re-emergence of KPC-producing isolates was observed post October 2013 with 18 further cases identified. Four K. pneumoniae isolates in the 2012 cluster and 16 from the 2013-2014 cluster were referred for further testing. All carried the KPC-2 beta-lactamase gene. The 2012 isolates were genetically similar to the 2014 isolates. CONCLUSION: KPC-2 mediated resistance is an emerging threat in Australia. The re-emergence of KPC despite initial containment emphasises the need for constant vigilance in the microbiology laboratory and ongoing maintenance of infection control and antimicrobial stewardship activity.

Validation of a turbulent Kelvin-Helmholtz shear layer model using a high-energy-density OMEGA laser experiment.

Following the successful demonstration of an OMEGA laser-driven platform for generating and studying nearly two-dimensional unstable plasma shear layers [Hurricane et al., Phys. Plasmas 16, 056305 (2009); Harding et al., Phys. Rev. Lett. 103, 045005 (2009)], this Letter reports on the first quantitative measurement of turbulent mixing in a high-energy-density plasma. As a blast wave moves parallel to an unperturbed interface between a low-density foam and a high-density plastic, baroclinic vorticity is deposited at the interface and a Kelvin-Helmholtz instability-driven turbulent mixing layer is created in the postshock flow due to surface roughness. The spatial scale and density profile of the turbulent layer are diagnosed using x-ray radiography with sufficiently small uncertainty so that the data can be used to ~0.17 µm) in the postshock plasma flow are consistent with an "inertial subrange," within which a Kolmogorov turbulent energy cascade can be active. An illustration of comparing the data set with the predictions of a two-equation turbulence model in the ares radiation hydrodynamics code is also presented.

Laser-driven plasma loader for shockless compression and acceleration of samples in the solid state.

A new method for shockless compression and acceleration of solid materials is presented. A plasma reservoir pressurized by a laser-driven shock unloads across a vacuum gap and piles up against an Al sample thus providing the drive. The rear surface velocity of the Al was measured with a line VISAR, and used to infer load histories. These peaked between approximately 0.14 and 0.5 Mbar with strain rates approximately 10(6)-10(8) s(-1). Detailed simulations suggest that apart from surface layers the samples can remain close to the room temperature isentrope. The experiments, analysis, and future prospects are discussed.

Experimental investigation of the three-dimensional interaction of a strong shock with a spherical density inhomogeneity.

Laser-driven experiments are described which probe the interaction of a very strong shock with a spherical density inhomogeneity. The interaction is viewed from two orthogonal directions enabling visualization of both the initial distortion of the sphere into a double vortex ring structure as well as the onset of an azimuthal instability that ultimately results in the three-dimensional breakup of the ring. The experimental results are compared with 3D numerical simulations and are shown to be in remarkable agreement with the incompressible theory of Widnall et al. [J. Fluid Mech. 66, 35 (1974)].