Functional Chitosan-Calcium Carbonate Coatings for Enhancing Water and Fungal Resistance of Paper Materials.

The objective of this study was to increase the water resistance of paper while providing fungal resistance using a bio-based coating made from chitosan. The water resistance was improved through the surface control of roughness using modified calcium carbonate particles. The higher the quantity of particles in the film-forming solution, the higher the surface hydrophobicity of the paper. The addition of particles was found to counterbalance the chitosan hydrophilicity through the control of the coatings' penetration in the paper bulk. As a consequence, the wetting time and liquid water resistance were enhanced. The antifungal activity of the film-forming solutions and coated paper was also investigated against the growth of Chaetomium globosum, which was selected as a model strain able to contaminate paper materials. The results reveal that the antifungal activity of chitosan was improved by a possible synergic effect with the bicarbonate ions from the mineral particles.

Synthesis and Characterization of Vanillin-Based π-Conjugated Polyazomethines and Their Oligomer Model Compounds.

The synthesis of π-conjugated polymers via an environmentally friendly procedure is generally challenging. Herein, we describe the synthesis of divanillin-based polyazomethines, which are derived from a potentially bio-based monomer. The polymerization is performed in 5 min under microwave irradiation without any metallic catalyst, with water as the only by-product. The vanillin-based polyazomethines were characterized by SEC, TGA, and UV-Vis spectroscopy. Model compounds were designed and characterized by X-ray diffraction and UV-Vis spectroscopy. The structure/properties study of vanillin-based azomethines used as models allowed us to unequivocally confirm the E configuration and to highlight the cross-conjugated nature of divanillin-based polymers.

Tuning the activity and selectivity of polymerised ionic liquid-stabilised ruthenium nanoparticles through anion exchange reactions.

The development of highly active and selective heterogeneous-based catalysts with tailorable properties is not only a fundamental challenge, but is also crucial in the context of energy savings and sustainable chemistry. Here, we show that ruthenium nanoparticles (RuNPs) stabilised with simple polymerised ionic liquids (PILs) based on N-vinyl imidazolium led to highly active and robust nano-catalysts in hydrogenation reactions, both in water and organic media. Of particular interest, their activity and selectivity could simply be manipulated through counter-anion exchange reactions. Hence, as a proof of concept, the activity of RuNPs could be reversibly turned on and off in the hydrogenation of toluene, while in the case of styrene, the hydrogenation could be selectively switched from ethylbenzene to ethylcyclohexane upon anion metathesis. According to X-ray photoelectron spectroscopy (XPS) and dynamic light scattering (DLS) analyses, these effects could originate not only from the relative hydrophobicity and solvation of the PIL corona but also from the nature and strength of the PIL-Ru interactions.

Oxidative Depolymerization of Alkaline Lignin from Pinus Pinaster by Oxygen and Air for Value-Added Bio-Sourced Synthons.

In this work, an efficient 3-step process targeting the chemical modification and purification of lignin oligomers from industrial alkaline lignin is described. The oxidative depolymerization process of alkaline lignin with O2 or Air pressure, without use of metal catalyst, led to the production of two fractions of lignin oligomers named 'precipitated lignin' and 'hydrosoluble lignin' with 40% and 60% yield, respectively. These fractions were characterized with a wide range of methods including NMR spectroscopy (31P, 2D-HSQC), SEC (in basic media), FTIR. NMR analyses revealed the presence of carboxylic acid functions at a ratio of 1.80 mmol/g and 2.80 mmol/g for the precipitated and hydrosoluble lignin, respectively, values much higher than what is generally found in native lignin (between 0.2 and 0.5 mmol/g). SEC analyses revealed the formation of low molar masses for the precipitated (2200 g/mol) and hydrosoluble fractions (1500 g/mol) in contrast to the alkaline lignin (3900 g/mol). It is worth noting that the hydrosoluble fraction of lignin is soluble in water at any pH. Both processes (oxygen and air) were successfully scaled up and showed similar results in terms of yield and functionalization.

Extraction and Characterization of Hemicelluloses from a Softwood Acid Sulfite Pulp.

Hemicelluloses were extracted from a softwood acid sulfite pulp in a three-step procedure. Further delignification step resulted in a holocellulose pulp containing only 1.7 wt.% of the lignin left. Cold caustic extraction (CCE) with 18 wt.% NaOH at 60 °C for 1 h was performed to solubilize hemicelluloses of the holocellulose. An unbleached cellulose pulp was then obtained 97% pure, which indicates that 89% of the hemicelluloses were removed. After purification, extraction yields between 1.1 wt.% and 9.5 wt.% were obtained from the delignified pulp and the hemicelluloses' chemical compositions and structures were investigated by 1H, 13C nuclear magnetic resonance spectroscopy (NMR) and two-dimensional NMR by correlation spectroscopy (2D-COSY) and proton-detected heteronuclear single-quantum correlation (2D-HSQC), high-performance anion-exchange chromatography coupled with a pulsed amperometry detector (HPAEC-PAD), size-exclusion chromatography coupled with a refractive index detector (SEC-RI) and thermogravimetric analyses (TGA). Hemicelluloses were obtained with a purity of 96%, with short cellulosic chains as the only residue. Sulfite pulping modified the hemicelluloses' structure, and it was found that two types of hemicelluloses were isolated, glucomannans, predominant at 67%, and methylglucuronoxylans. Finally, alkali-soluble hemicelluloses displayed relatively narrow size distributions and low molar masses, Mw varying between 18,900 and 30,000 g/mol after acid sulfite pulping.

Divanillin-Based Polyazomethines: Toward Biobased and Metal-Free π-Conjugated Polymers.

Divanillin was synthesized in high yield and purity using Laccase from Trametes versicolor. It was then polymerized with benzene-1,4-diamine and 2,7-diaminocarbazole to form polyazomethines. Polymerizations were performed under microwave irradiation and without transition-metal-based catalysts. These biobased conjugated polyazomethines present a broad fluorescence spectrum ranging from 400 to 600 nm. Depending on the co-monomer used, polyazomethines with molar masses of around 10 kg·mol-1 and with electronic gaps ranging from 2.66 to 2.85 eV were obtained. Furthermore, time-dependent density functional theory (TD-DFT) calculations were performed to corroborate the experimental results.

Divanillin-Based Aromatic Amines: Synthesis and Use as Curing Agents for Fully Vanillin-Based Epoxy Thermosets.

Bio-based aromatic diamines from vanillin substrate were successfully synthesized and characterized. These amines, i.e., methylated divanillylamine (MDVA) and 3,4-dimethoxydianiline (DMAN), were then tested as curing agents for the design of bio-based epoxy thermosets. The epoxy thermosets obtained from these novel vanillin-based amines exhibited promising thermomechanical properties in terms of glass transition temperature and char residue.

Synthesis and Self-Assembly of Xylan-Based Amphiphiles: From Bio-Based Vesicles to Antifungal Properties.

This work aims at designing functional biomaterials through selective chemical modification of xylan from beechwood. Acidic hydrolysis of xylan led to well-defined oligomers with an average of six xylose units per chain and with an aldehyde group at the reductive end. Reductive amination was performed on this aldehyde end group to introduce an azide reactive group. "Click chemistry" was then applied to couple these hydrophilic xylans moieties with different hydrophobic fatty acid methyl esters that were previously functionalized with complementary alkyne functions. The resulting amphiphilic bio-based conjugates were then self-assembled using three different methods, namely, direct solubilization, thin-film rehydration/extrusion, and microfluidics. Well-defined micelles and vesicles were obtained, and their high loading capacity with propiconazole as an antifungal active molecule was shown. The resulting vesicles loaded with propiconazole in a microfluidic process proved to significantly improve the antifungal activity of propiconazole, demonstrating the high potential of such xylan-based amphiphiles.

On the direct use of CO2 in multicomponent reactions: introducing the Passerini four component reaction.

We introduce a novel isocyanide-based multicomponent reaction, the Passerini four component reaction (P-4CR), by replacing the carboxylic acid component of a conventional Passerini three component reaction (P-3CR) with an alcohol and CO2. Key to this approach is the use of a switchable solvent system, allowing the synthesis of a variety of α-carbonate-amides. The reaction was first investigated and optimized using butanol, isobutyraldehyde, tert-butyl isocyanide and CO2. Parameters investigated included the effect of reactant equivalents, reactant concentration, solvent, catalyst, catalyst concentration and CO2 pressure. Of the other parameters, the purity of the aldehyde and its tendency to oxidize was one of the most critical parameters for a successful P-4CR. After optimization, a total of twelve (12) P-4CR compounds were synthesized with conversions ranging between 16 and 82% and isolated yields between 18 and 43%. Their structures were confirmed via 1H and 13C NMR, FT-IR and high resolution mass spectrometry (ESI-MS). In addition, three (3) hydrolysis products of P-4CR (α-hydroxyl-amides) were successfully isolated with yields between 23 and 63% and fully characterized (1H, 13C NMR, FT-IR and ESI-MS) as well.

Telechelic Polybutadienes or Polyisoprenes Precursors for Recyclable Elastomeric Networks.

(Bis)furan-telechelic, low-molar-mass polybutadienes and polyisoprenes are synthesized by controlled degradation of high molar mass polymers and chain-end modifications yielding difunctional, trifunctional, or tetrafunctional polymers. Addition of a bismaleimide to the liquid-modified polymer leads to the formation of a thermoreversible elastomeric network based on the Diels-Alder chemistry for the trifunctional or tetrafunctional polymers, whereas only chain extension occurs for the bifunctional one. Dynamic mechanical analyses or tensile tests are performed on the networks and reveal a similar behavior for polyisoprene and polybutadiene with nevertheless quite different Young modulus or strain at break. The retro Diels-Alder reaction occurs upon heating, allowing the remolding of the used elastomer. The remolded network exhibits the same mechanical properties as the initial network, showing an efficient material recyclability.

Cellulose oligomers production and separation for the synthesis of new fully bio-based amphiphilic compounds.

Cellulose oligomers are water-soluble, on the contrary to cellulose, which greatly increase their application range. In this study, cellulose oligomers were obtained from the acidic hydrolysis of cellulose with phosphoric acid. The global yield in water-soluble oligomers was around 23% with polymerization degree (DP) ranging from 1 to 12. The cellulose oligomers DP distribution was successfully reduced by differential solubilisation in methanol as one of the goals of this work was to avoid the use of a time-consuming full chromatographic separation. The methanol-soluble oligomers were mainly low DP (≤3). The oligomers of higher molar mass, composed of 42% of cellotetraose and 36% of cellopentaose, were then functionalized and coupled with stearic acid through azide-alkyne click chemistry to obtain amphiphilic compounds. The self-assembly of these new bio-based compounds was finally investigated by dynamic light scattering (DLS) and transmission electron microscopy (TEM) and their critical micellar concentration (CMC) was found to be in the same range as alkylmaltosides and alkylglucosides.

Periodate oxidation of 4-O-methylglucuronoxylans: Influence of the reaction conditions.

This work aims at studying the sodium periodate oxidation of 4-O-methylglucuronoxylans (MGX) in different experimental conditions for a control of the oxidation degree. A series of sodium periodate oxidation reactions were conducted at three NaIO4/xylose molar ratios: 0.05, 0.20 and 1.00. The effects of xylan molar mass, xylan concentration and reaction temperature on the reaction rate have been evaluated by UV/visible spectroscopy at 0.20 NaIO4/xylose ratio. No depolymerization is observed at 0.05 ratio while depolymerization occurs at 0.20 and is even complete at 1.00 NaIO4/xylose ratio. An increase of the reaction temperature - up to 80 °C - leads to an increase of the oxidation rate with no effect on the depolymerization. At high xylan concentrations, the oxidation rate increases but promotes chains aggregation.

From Lignin-derived Aromatic Compounds to Novel Biobased Polymers.

Nowadays, the synthesis of (semi)aromatic polymers from lignin derivatives is of major interest, as aromatic compounds are key intermediates in the manufacture of polymers and lignin is the main source of aromatic biobased substrates. Phenols with a variety of chemical structures can be obtained from lignin deconstruction; among them, vanillin and ferulic acid are the main ones. Depending on the phenol substrates, different chemical modifications and polymerization pathways are developed, leading to (semi)aromatic polymers covering a wide range of thermomechanical properties. This review discusses the synthesis and properties of thermosets (vinyl ester resins, cyanate ester, epoxy, and benzoxazine resins) and thermoplastic polymers (polyesters, polyanhydrides, Schiff base polymers, polyacetals, polyoxalates, polycarbonates, acrylate polymers) prepared from vanillin, ferulic acid, guaiacol, syringaldehyde, or 4-hydroxybenzoic acid.

Influence of the variation of the alkyl chain length of N-alkyl-ß-D-glycosylamine derivatives on antifungal properties.

Twelve new glucosidic and galactosidic derivatives of N-alkylaminosugars with different alkylamines from 6 to 18 carbons were synthesized and characterized by (1)H and (13)C NMR. Their antifungal activity against the food fungal pathogen Aspergillus niger was evaluated using the radial growth assay. The influence of the variation of the alkyl chain length of N-alkylaminosugars on the mycelium growth was then discussed. Inhibition by the different alkylamines is shown as a biostatic effect rather than a biocidal effect. It was observed that alkylamines keep their antifungal properties after a thermal treatment compatible with food packaging and processing.

Styrene-spaced copolymers including anthraquinone and ß-O-4 lignin model units: synthesis, characterization and reactivity under alkaline pulping conditions.

A series of random copoly(styrene)s has been synthesized via radical polymerization of functionalized anthraquinone (AQ) and ß-O-4 lignin model monomers. The copolymers were designed to have a different number of styrene spacer groups between the AQ and ß-O-4 lignin side chains aiming at investigating the distance effects on AQ/ß-O-4 electron transfer mechanisms. A detailed molecular characterization, including techniques such as size exclusion chromatography, MALDI-TOF mass spectrometry, and (1)H, (13)C, (31)P NMR and UV-vis spectroscopies, afforded quantitative information about the composition of the copolymers as well as the average distribution of the AQ and ß-O-4 groups in the macromolecular structures. TGA and DSC thermal analysis have indicated that the copolymers were thermally stable under regular pulping conditions, revealing the inertness of the styrene polymer backbone in the investigation of electron transfer mechanisms. Alkaline pulping experiments showed that close contact between the redox active side chains in the copolymers was fundamental for an efficient degradation of the ß-O-4 lignin model units, highlighting the importance of electron transfer reactions in the lignin degradation mechanisms catalyzed by AQ. In the absence of glucose, AQ units oxidized phenolic ß-O-4 lignin model parts, mainly by electron transfer leading to vanillin as major product. By contrast, in presence of glucose, anthrahydroquinone units (formed by reduction of AQ) reduced the quinone-methide units (issued by dehydration of phenolic ß-O-4 lignin model part) mainly by electron transfer leading to guaiacol as major product. Both processes were distance dependent.

Synthesis of D-glucosamine quaternary ammonium derivatives and evaluation of their antifungal activity together with aminodeoxyglucose derivatives against two wood fungi Coriolus versicolor and Poria placenta: structure-activity relationships.

BACKGROUND: Structure-activity relationships are often reported in scientific studies. These may be employed in searching for new acceptable biocides to use against harmful microorganisms, because the biocides used hitherto encounter various problems, including lack of efficiency, high toxicity and persistence. Nowadays, scientists are trying to find new, environmentally acceptable biocides to replace these earlier biocides. Different compounds from renewable materials have been studied and have shown pronounced antifungal activity against wood fungi. These include aminopolysaccharide derivatives and different quaternary ammonium polymers. A biological study carried out with these products indicated a possible relationship between amino groups and differences in biological activity observed. RESULTS: In this study, an amino group was successively fixed to different carbon atoms of glucose, and glucosamine was also modified by both N-alkylation and quaternisation. The impact of the amino group position on antifungal activity against two wood decay fungi was investigated. The amino group at the anomeric position showed the highest antifungal activity against both Coriolus versicolor Quel. and Poria placenta (Fr.) Cooke. Furthermore, the positive impact of both N-alkylation and quaternisation on the growth of both strains was demonstrated. CONCLUSION: The anomeric position of the amino group and the N-alkylation and quaternisation of amino sugars considerably increase the antifungal activity of these compounds.

Hydrophobization and antimicrobial activity of chitosan and paper-based packaging material.

This study reports the elaboration of water-resistant, antimicrobial, chitosan and paper-based materials as environmentally friendly food packaging materials. Two types of papers were coated with chitosan-palmitic acid emulsions or with a blend of chitosan and O,O'-dipalmitoylchitosan (DPCT). Micromorphology studies showed that inclusion of hydrophobic compounds into the chitosan matrix was enhanced by grafting them onto chitosan and that this led to their penetration of the paper's core. Compared to chitosan-coated papers, the coating of chitosan-palmitic emulsion kept vapor-barrier properties unchanged (239 and 170 g.m(-2).d(-1) versus 241 and 161 g.m(-2).d(-1)), while the coating of chitosan-DPCT emulsion dramatically deteriorated them (441 and 442 g.m(-2).d(-1)). However, contact angle measurements (110-120 degrees after 1 min) and penetration dynamics analysis showed that both strategies improved liquid-water resistance of the materials. Kit-test showed that all hydrophobized chitosan-coated papers kept good grease barrier properties (degree of resistance 6-8/12). Finally, all chitosan-coated materials exhibited over 98% inhibition on Salmonella Typhimurium and Listeria monocytogenes .

Synthesis and antibacterial activity of aminodeoxyglucose derivatives against Listeria innocua and Salmonella typhimurium.

In this study aminodeoxyglucose derivatives were synthesized and evaluated for their antibacterial activity against two food bacteria, Listeria innocua and Salmonella typhimurium . 6-Amino-6-deoxy-alpha-D-methylglucopyranose (GSA-6), 3-amino-3-deoxy-D-glucopyranoside (GSA-3), and beta-D-glucopyranosylamine (GSA-1) were synthesized and concurrently tested with commercially available D-glucosamine (GSA-2) for antibacterial activity. Results obtained from this study showed a pronounced antagonist effect due to the position of amino groups of aminoglucose derivatives on the antibacterial activity. GSA-3 was the most active compound. At a concentration of 2 x 10(-4) mol mL(-1), it delayed the growth of both bacteria with percentages of inhibition of 29 and 15% for L. innocua and S. typhimurium, respectively. At the same concentration the percentages of inhibition for other aminodeoxyglucoses varied between 5 and 18% and between 2 and 11% for L. innocua and S. typhimurium, respectively. All compounds were characterized by FTIR, (1)H NMR, and (13)C NMR spectroscopy.

Advances on selective C-6 oxidation of chitosan by TEMPO.

The specific C-6 oxidation by TEMPO of chitosan and chitosan derivatives were studied to obtain tailored bioactive biopolymers. The modifications on chitosan presented many difficulties and showed the adverse effect of the amine moieties of chitosan on this reaction. Thus, protections of the amino groups by N-acetylation or N-phthaloylation were studied and followed by the C-6 specific oxidations of the resulting polymers. The desired 6-carboxychitosan could not be obtained after deprotection; the reactions with TEMPO led to degradation of the polymers. The specific oxidation of a potentially bioactive derivative of chitosan was then achieved by the oxidation of a quaternized chitosan: N, N, N-trimethylchitosan. N, N, N-Trimethyl-6-carboxychitosan was characterized by FTIR spectroscopy, 1H, and 13C NMR spectroscopy.

Synthesis and evaluation of N-alkyl-beta-D-glucosylamines on the growth of two wood fungi, Coriolus versicolor and Poria placenta.

Various glucosylamines were synthesized from glucose and different alkyl amine compounds. These amino compounds are beta-D-glucopyranosylamine (GPA), N-ethyl-beta-D-glucopyranosylamine (EtGPA), N-butyl-beta-D-glucopyranosylamine (BuGPA), N-hexyl-beta-D-glucopyranosylamine (HeGPA), N-octyl-beta-D-glucopyranosylamine (OcGPA), N-dodecyl-beta-D-glucopyranosylamine (DoGPA), N-(2-hydroxyethyl)-beta-D-glucopyranosylamine (HEtGPA) and N,N-di(2-hydroxyethyl)-beta-D-glucopyranosylamine (DHEtGPA). They were tested for their antifungal activity against the growth of Coriolus versicolor and Poria placenta. An improvement of the antifungal activity with the increase of alkyl chain length was observed. DoGPA exhibited the best antifungal activity against both strains. It completely inhibited the fungal growth at 0.01x10(-3)molmL(-1) and 0.0075x10(-3)molmL(-1) for C. versicolor and P. placenta, respectively. For other glucosylamines higher concentrations were needed for complete inhibition of fungi.