A Novel Approach to Waste Recycling and Dye Removal: Lithium-Functionalized Nanoparticle Zeolites.

A zeolitic sample, named MT-ZLSH, was synthesized using mining tailings (MT) as the precursor material, resulting in a structure comprising: Linde type A (LTA) and sodalite-hydroxysodalite (ZLSH). This naming convention reflects the material's origin and its structural characteristics. The material was further modified by incorporating lithium, producing MT-ZLSH-Li+. Physicochemical characterizations were performed, and the material was evaluated for its potential to remove methylene blue (MB) from synthetic wastewater through adsorption and photocatalysis. Efficient adsorption was observed under typical wastewater pH conditions, with a maximum adsorption capacity of 23.4 mg·g-1, which fit well with the Langmuir isotherm model. The key mechanisms governing MB adsorption were identified as ion exchange, electrostatic attraction, and hydrogen bonding. The adsorption process was exothermic, with kinetic data fitting both the pseudo-second order and intraparticle diffusion models, achieving 82% removal and a maximum adsorption capacity of 40 mg·g-1 over 12 h. MB adsorption followed a two-step process, initially involving film diffusion, followed by intraparticle diffusion. Additionally, photocatalytic degradation of MB achieved 77% degradation within 180 min. However, a decrease in reusability was observed during a second cycle of MB adsorption and photodegradation, highlighting the need for further optimization to enhance the material's long-term performance.

Evaluation of the Effectiveness of Geogrids Manufactured from Recycled Plastics for Slope Stabilization-A Case Study.

This study aimed to investigate the sustainable use of recycled plastics, specifically polypropylene (PP) and high-density polyethylene (HDPE), in the manufacture of geogrids for geotechnical and civil engineering applications. Plastics were collected from a recycling center, specifically targeting containers used for food, cleaning products, and other domestic packaging items. These plastics were sorted according to the Möbius triangle classification system, with HDPE (#2) and PP (#5) being the primary categories of interest. The research methodologically evaluates the mechanical properties of PP/HDPE (0/100, 25/75, 50/50, 75/25 and 100/0% w/w) composites through tensile and flexural tests, exploring various compositions and configurations of geogrids. The results highlight the superiority of pure recycled HDPE processed into 1.3 mm thick laminated yarns and hot air welded for 20 to 30 s, exhibiting a deformation exceeding 60% in comparison to the PP/HDPE composites. Through SolidWorks® Simulation, it was shown that the adoption of a trigonal geogrid geometry optimizes force distribution and tensile strength, significantly improving slope stabilization efficiency. Based on the results obtained, a laboratory-scale prototype geogrid was developed using an extrusion process. The results underscore the importance of careful composite design and yarn configuration selection to achieve the desired mechanical properties and performance in geogrid applications. It emphasizes the potential of recycled plastics as a viable and environmentally friendly solution for stabilizing slopes, contributing to the reduction in plastic waste and promoting sustainable construction practices.

From Waste to Added-Value Product: Synthesis of Highly Crystalline LTA Zeolite from Ore Mining Tailings.

The use of wastes is necessary to contribute to environmental sustainability. In this study, ore mining tailings were used as the raw material and precursor for the synthesis of LTA zeolite, a value-added product. Pre-treated mining tailings were submitted to the synthesis stages under specific established operational conditions. The physicochemical characterization of the synthesized products was performed with XRF, XRD, FTIR and SEM, to identify the most cost-effective synthesis condition. The LTA zeolite quantification and its crystallinity were determined as effects of the SiO2/Al2O3, Na2O/SiO2 and H2O/Na2O molar ratios used, as well as the influence of the synthesis conditions: mining tailing calcination temperature, homogenization, aging and hydrothermal treatment times. The zeolites obtained from the mining tailings were characterized by the LTA zeolite phase accompanied by sodalite. The calcination of mining tailings favored the production of LTA zeolite, and the influence of the molar ratios, aging and hydrothermal treatment times were determined. Highly crystalline LTA zeolite was obtained in the synthesized product at optimized conditions. Higher methylene blue adsorption capacity was associated with the highest crystallinity of synthesized LTA zeolite. The synthesized products were characterized by a well-defined cubic morphology of LTA zeolite and lepispheres of sodalite. The incorporation of lithium hydroxide nanoparticles over LTA zeolite synthesized (ZA-Li+) from mining tailings yielded a material with improved features. The adsorption capacity towards cationic dye was higher than for anionic dye, especially for methylene blue. The potential of using ZA-Li+ in environmental applications related to methylene blue deserves detailed study.

Fe3+/Mn2+ (Oxy)Hydroxide Nanoparticles Loaded onto Muscovite/Zeolite Composites (Powder, Pellets and Monoliths): Phosphate Carriers from Urban Wastewater to Soil.

The development of an efficient adsorbent is required in tertiary wastewater treatment stages to reduce the phosphate-phosphorous content within regulatory levels (1 mg L-1 total phosphorous). In this study, a natural muscovite was used for the preparation of muscovite/zeolite composites and the incorporation of Fe3+/Mn2+ (oxy)hydroxide nanoparticles for the recovery of phosphate from synthetic wastewater. The raw muscovite MC and the obtained muscovite/sodalite composite LMC were used in the powder form for the phosphate adsorption in batch mode. A muscovite/analcime composite was obtained in the pellets PLMCT3 and monolith SLMCT2 forms for the evaluation in fixed-bed mode for continuous operation. The effect of pH, equilibrium and kinetic parameters on phosphate adsorption and its further reuse in sorption-desorption cycles were determined. The characterization of the adsorbents determined the Fe3+ and Mn2+ incorporation into the muscovite/zeolite composite's structure followed the occupancy of the extra-framework octahedral and in the framework tetrahedral sites, precipitation and inner sphere complexation. The adsorbents used in this study (MC, LMC, PLMCT3 and SLMCT2) were effective for the phosphate recovery without pH adjustment requirements for real treated wastewater. Physical (e.g., electrostatic attraction) and chemical (complexation reactions) adsorption occurred between the protonated Fe3+/Mn2+ (oxy)hydroxy groups and phosphate anions. Higher ratios of adsorption capacities were obtained by powder materials (MC and LMC) than the pellets and monoliths forms (PLMCT3 and SLMCT2). The equilibrium adsorption of phosphate was reached within 30 min for powder forms (MC and LMC) and 150 min for pellets and monoliths forms (PLMCT3 and SLMCT2); because the phosphate adsorption was governed by the diffusion through the internal pores. The adsorbents used in this study can be applied for phosphate recovery from wastewater treatment plants in batch or fixed-bed mode with limited reusability. However, they have the edge of environmentally friendly final disposal being promissory materials for soil amendment applications.

Comparative Study of Donepezil-Loaded Formulations for the Treatment of Alzheimer's Disease by Nasal Administration.

Alzheimer's disease is characterized by a progressive deterioration of neurons resulting in a steady loss of cognitive functions and memory. Many treatments encounter the challenge of overcoming the blood-brain barrier, thus the intranasal route is a non-invasive effective alternative that enhances the drug delivery in the target organ-the brain-and reduces the side effects associated with systemic administration. This study aimed at developing intranasal gels of donepezil as an approach to Alzheimer's disease. Three different gels were elaborated and characterized in terms of pH, morphology, gelation temperature, rheology, and swelling. An in vitro release study and an ex vivo permeation in porcine nasal mucosa were conducted on Franz diffusion cells. The tolerability of the formulations was determined by the cytotoxicity in human nasal cells RPMI 2650. Results showed that pluronic gels exhibit the higher release rate and enhanced permeation compared to chitosan gel. Moreover, the combination of Pluronic F-127 and Transcutol® P exerted a synergic effect on the permeation of donepezil through the nasal mucosa. The resulting gels showed suitable tolerance in the RPMI 2650 cell line and physicochemical characteristics for intranasal delivery, and thus gel formulations administered by nasal mucosa could be an alternative strategy to improve the bioavailability of donepezil.

Effect of Mn2+/Zn2+/Fe3+ Oxy(Hydroxide) Nanoparticles Doping onto Mg-Al-LDH on the Phosphate Removal Capacity from Simulated Wastewater.

A parent Mg-Al-LDH was upgraded in its adsorption properties due to the incorporation of tri-metal species oxy(hydroxide) nanoparticles obtaining Mn2+/Zn2+/Fe3+/Mg-Al-LDH composite for the phosphate recovery from simulated urban treated wastewater. The physicochemical properties of the synthesized Mn2+/Zn2+/Fe3+/Mg-Al-LDH make promising for real application without being environmentally harmful. The performance of Mn2+/Zn2+/Fe3+/Mg-Al-LDH composite was evaluated through batch adsorption assays. The support of iron, manganese, and zinc (oxy)hydroxide nanoparticles onto the parent Mg-Al-LDH structure was performed by precipitation, isomorphic substitution, and complexation reactions. The main improvement of the Mn2+/Zn2+/Fe3+/Mg-Al-LDH composite was the highest phosphate adsorption capacity (82.3 mg∙g-1) in comparison to the parent Mg-Al-LDH (65.3 mg∙g-1), in a broad range of concentrations and the effective phosphate adsorption at neutral pH (7.5) near to the real wastewater effluents conditions in comparison to the conventional limitations of other adsorbents. The effectiveness of Mn2+/Zn2+/Fe3+/Mg-Al-LDH composite was higher than the conventional metal LDHs materials synthesized in a single co-precipitation step. The phosphate adsorption onto Mn2+/Zn2+/Fe3+/Mg-Al-LDH composite was described to be governed by both physical and chemical interactions. The support of Mn2+/Zn2+/Fe3+ oxy(hydroxide) nanoparticles over the parent Mg-Al-LDH was a determinant for the improvement of the phosphate adsorption that was governed by complexation, hydrogen bonding, precipitation, and anion exchange. The intra-particular diffusion also described well the phosphate adsorption onto the Mn2+/Zn2+/Fe3+/Mg-Al-LDH composite. Three specific stages of adsorption were determined during the phosphate immobilization with an initial fast rate, followed by the diffusion through the internal pores and the final equilibrium stage, reaching 80% of removal and the equilibrium within 1 h. The Mn2+/Zn2+/Fe3+/Mg-Al-LDH was strongly selective towards phosphate adsorption in presence of competing ions reducing the adsorption capacity at 20%. The Mn2+/Zn2+/Fe3+/Mg-Al-LDH has limited reusability, only 51% of the adsorbed phosphate could be recovered in the second cycle of the adsorption-desorption process. Around 14% of phosphate was loosely-bond to Mn2+/Zn2+/Fe3+/Mg-Al-LDH which brings the opportunity to be a new source of phosphorus. The use of eluted concentrates and the final disposal of the exhausted adsorbent for soil amendment applications can be an integral nutrient system (P, Mn, Zn, Fe) for agriculture purposes.

LTA and FAU-X Iron-Enriched Zeolites: Use for Phosphate Removal from Aqueous Medium.

Hydrothermally synthesized Linde type A (LTA) and faujasite X (FAU-X) zeolites are low-cost and environmentally benign inorganic carriers for environmental applications. In this study, (oxy)hydroxides were incorporated onto LTA and FAU-X zeolites to promote the phosphate adsorption. The performance of LTA-Fe and FAU-X-Fe was evaluated through batch adsorption assays. A complete evaluation was performed to recover phosphate from synthetic wastewater. The effect of pH, concentration, equilibrium, and kinetic parameters on phosphate adsorption and its further reuse in sorption-desorption cycles were evaluated. LTA-Fe and FAU-X-Fe are effective for adsorption of phosphate at neutral (e.g., pH 7.0 ± 0.2) and in a broad range of phosphate concentrations. Higher ratios of adsorption capacities were obtained by synthetic zeolites enriched with iron in comparison to their parent forms. The phosphate adsorption occurred through hydrogen bonding and complexation reactions between protonated iron hydroxyl groups and phosphate anions. The phosphate monolayer adsorption was followed by diffusion through the internal pores and 80% of the equilibrium adsorption was reached within 50 min. The LTA-Fe and FAU-X-Fe can be used for phosphate recovery from wastewater treatment plants. The use of LTA-Fe and FAU-X-Fe in a tertiary wastewater treatment stage could allow to reduce the phosphate-phosphorous content, reaching the regulatory levels (equal 1 mg L-1 total phosphorous). The phosphate adsorption using LTA-Fe and FAU-X-Fe does not require pH adjustment, and it is endothermic. The reusability of both iron zeolites is limited, and they can be finally disposed for soil amendment applications.

Elimination of total coliforms and Escherichia coli from water by means of filtration with natural clays and silica sand in developing countries.

This research presents the results of a pilot system used for water treatment to be supplied to single-family or small housing nucleus at rural sector. The pilot system is constituted by an up-flow aerated filter with ceramic carrier, followed by a second down-flow filter of silica sand. The pilot plant was installed in a rural sector of the province of Loja, Ecuador, with the main purpose of monitoring the reduction in bacteria in the water for human consumption. Two natural clays from the area were tested. They were transformed into sphere-type ceramics, and then, they were placed in the pilot filters. These both natural clays are inorganic materials with high content of aluminosilicate clay minerals with favourable characteristics to achieve greater efficiency for the reduction in bacteria. The acclimatization time of 60 days allowed to achieve optimum treatment efficiency performance until 90 days of operation. The physicochemical parameters, namely temperature, pH, dissolved oxygen and total dissolved solids, were monitored throughout the experiments. Regarding microbiological parameters, up to 99% of total coliforms removal was reached for the clay called CF-CC and 79% for the other, called CF-CV. In addition, 100% of total coliforms and Escherichia Coli removal was reached for both clay systems. Social and economic viability of the proposed treatment is also analysed in the manuscript.

Use of nutrient-enriched zeolite (NEZ) from urban wastewaters in amended soils: Evaluation of plant availability of mineral elements.

The usefulness of a nutrient-enriched zeolite (NEZ) obtained from simultaneous ammonium (NH4+) and phosphate (PO43-) recovery from urban wastewaters was evaluated as soil amendment through the early growth of sunflower (Helianthus annuus). The NEZ systems were applied to sandy (acid) and clayey (basic) soils from Mediterranean agricultural areas (Spain). Some plant growth indicators were measured: evapotranspiration, plant moisture content, plant biomass, root/shoot ratio, nitrogen and phosphorous uptake and the C/N ratio. The experimental data exhibited differences in the growth indicators for un-amended and amended soils. The addition of the NEZ system increase the plant water content of sunflowers grown on clay soils. The plant biomass of sunflower was improved by the incorporation of NEZ system in all treatments for the two soils studied. A reduction of the root/shoot ratio for the treatments of clay soil by application of NEZ systems were observed. The content of ammonium and phosphorous in tissues increased considerably with the addition of amendment material. Besides, the ammonium, nitrate and inorganic phosphorous in the post-test soils revealed that nutrients were still available for a second growth cycle. As demonstrated in previous work, the NEZ system releases nutrients continuously controlled by soil pH and mineral composition as well as the irrigation conditions provided. Therefore, this approach of amendment materials for soil seems to be a promising alternative for agricultural practice, where the dose selection must be balanced according to the plant's nutrient needs and soil properties by adjusting the growth conditions.

Valorisation of N and P from waste water by using natural reactive hybrid sorbents: Nutrients (N,P,K) release evaluation in amended soils by dynamic experiments.

The removal of nutrients (nitrogen (N), phosphorous (P)) from waste water has become a resource recovery option in recent regulations worldwide, as observed in the European Union. Although both of these nutrients could be recovered from the sludge line, >70-75% of the N and P is discharged into the water line. Efforts to improve the nutrient recovery ratios have focused on developing low-cost technologies that use sorption processes. In this study, a natural zeolite (clinoptilolite type) in its potassium (K) form was impregnated with hydrated metal oxides and used to prepare natural hybrid reactive sorbents (HRS) for the simultaneous recovery of ammonium (NH4+) and phosphate (PO43-) from treated urban waste water. Three unfertile soils (e.g., one acidic and two basic) amended with N-P-K charged HRS were leached with deionized water (e.g. to simulate infiltration in the field) at two- and three-day time intervals over 15 different leaching cycles (equivalent to 15 bed volumes). The N-P-K leaching profiles for the three charged hybrid sorbents exhibited continuous nutrient release, with their values dependent on the composition of minerals in the soils. In the basic soil that is rich in illite and calcite, the release of potassium (K+) and ammonium (NH4+) is favoured by-ion exchange with calcium (Ca2+) and accordingly diminishes the release of phosphate (PO43-) due to its limited solubility in saturated calcite solutions (pH8 to 9). The opposite is true for sandy soils that are rich in albite (both acidic and basic), whereas the release of NH4+ and K+ was limited and the values of both ions measured in the leaching solutions were below 1mg/L. Their leaching solutions were poor in Ca2+, and the release of PO43- was higher (up to 12mgP-PO43-/L). The nutrient releases necessary for plant growth were provided continuously and were controlled primarily by the soil mineral dissolution rates fixing the soil aqueous solution composition (e.g. pH and ionic composition; in particular, the presence of calcite is a determinant for nutrient release, especially in alkaline soils). The N-P-K charged HRS sorbents that were used for soil amendment may be an alternative for avoiding nutrient leaching and reaching the goals of soil sustainability in agriculture and reducing the nutrient overloading of surface waters.