RESUMO
"Perovskite / Carbon" interface has remained a key bottleneck for the hole-conductor-free perovskite solar cells based on carbon-electrode (CPSCs), due to problems like loose physics contact, defects, energy mismatch, poor chemical coupling, etc. A previous study shows that octylammonium iodide (OAI) blending in carbon paste induced a kind of "in-situ healing" effect for "perovskite / carbon" interface, and improved power conversion efficiency from ≈13% to >19%. Here the beneath mechanism is further explored by careful examination of the interaction between OAI molecule and carbon black (CB) nanoparticles. It comes to show that, the famous "CB adsorption" plays a key role during the "healing" processes. Due to CB adsorption behavior, the mass ratio between OAI and CB influences much on the healing effect. By suitably adjusting the mass ratio between OAI and CB, and increasing the light harvest of perovskite, an efficiency of 19.41% is achieved for the hole-conductor-free CPSCs. Device efficiency and the charge-extraction and recombination process are tracked with the storage period, continuous improvement appears for devices assembled by relatively higher CB mass. A kind of "slow-release effect" is revealed during the OAI-induced "in-situ healing" process, which is caused by the famous "CB adsorption" behavior.
RESUMO
"Perovskite/carbon" interface is a bottle-neck for hole-conductor-free, carbon-electrode basing perovskite solar cells due to the energy mismatch and concentrated defects. In this article, in-situ healing strategy is proposed by doping octylammonium iodide into carbon paste that used to prepare carbon-electrode on perovskite layer. This strategy is found to strengthen interfacial contact and reduce interfacial defects on one hand, and slightly elevate the work function of the carbon-electrode on other hand. Due to this effect, charge extraction is accelerated, while recombination is obviously reduced. Accordingly, power conversion efficiency of the hole-conductor-free, planar perovskite solar cells is upgraded by ≈50%, or from 11.65 (± 1.59) % to 17.97 (± 0.32) % (AM1.5G, 100 mW cm-2 ). The optimized device shows efficiency of 19.42% and open-circuit voltage of 1.11 V. Meanwhile, moisture-stability is tested by keeping the unsealed devices in closed chamber with relative humidity of 85%. The "in-situ healing" strategy helps to obtain T80 time of >450 h for the carbon-electrode basing devices, which is four times of the reference ones. Thus, a kind of "internal encapsulation effect" has also been reached. The "in situ healing" strategy facilitates the fabrication of efficient and stable hole-conductor-free devices basing on carbon-electrode.
RESUMO
Polyvinyl pyrrolidone (PVP) is doped to PbI2 and organic salt during two-step growth of halideperovskite. It is observed that PVP molecules can interact with both PbI2 and organic salt, reduce the aggregation and crystallization of the two, and then slow down the coarsening rate of perovskite. As doping concentration increases from 0 to 1 mM in organic salt, average crystallite size of perovskite decreases monotonously from 90 to 34 nm; Surface fluctuation reduces from 259.9 to 179.8 nm at first, and then increases; Similarly, surface roughness decreases from 45.55 to 26.64 nm at first, and then rises. Accordingly, a kind of "confinement effect" is resolved to crystallite growth and surface fluctuation/roughness, which helps to build compact and uniform perovskite film. Density of trap states (t-DOS) is cut down by ≈60% at moderate doping (0.2 mM). Due to the "confinement effect", power conversion efficiency of perovskite solar cells is improved from 19.46 (±2.80) % to 21.50 (±0.99) %, and further improved to 24.11% after surface modification. Meanwhile, "confinement effect" strengthens crystallite/grain boundaries and improves thermal stability of both film and device. T80 of device increases to 120 h, compared to 50 h for reference ones.
RESUMO
Fast reaction between organic salt and lead iodide always leads to small perovskite crystallites and concentrated defects. Here, polyacrylic acid is blended with organic salt, so as to regulate the crystallization in a two-step growth method. It is observed that addition of polyacrylic acid retards aggregation and crystallization behavior of the organic salt, and slows down the reaction rate between organic salt and PbI2 , by which "slow-release effect" is defined. Such effect improves crystallization of perovskite. X-ray diffraction study shows that, after addition of 2 mm polyacrylic acid, average crystallite size of perovskite increases from ≈40 to ≈90 nm, meanwhile, grain size increases. Thermal admittance spectroscopy study shows that trap density is reduced by nearly one order (especially for deep energy levels). Due to the improved crystallization and reduced trap density, charge recombination is obviously reduced, while lifetime of charge carriers in perovskite film and devices are prolonged, according to time-resolved photoluminescence and transient photo-voltage decay curve tests, respectively. Accordingly, power conversion efficiency of the device is promoted from 19.96 (±0.41)% to 21.84 (±0.25)% (with a champion efficiency of 22.31%), and further elevated to 24.19% after surface modification by octylammonium iodide.