Improved Exopolymer Production by Chromohalobacter canadensis Cultures for Its Potential Cosmeceutical Applications.

Several exopolymers with different chemical composition and correspondingly variety in their physico-chemical properties from halophilic microorganisms have still been described, however, with a low production yield. Chromohalobacter canadensis 28 isolated from Pomorie saltern synthesized an unusual exopolymer (EP) containing 72% γ-polyglutamic acid (PGA), an essential cosmeceutical additive. Current work suggests a novel approach for effective EP synthesis by C. canadensis 28 using continuous cultures. Highest production was observed at low dilution rates reaching a level of 2.1 mg/mL at D = 0.035, similar to those in batch cultures (2.34 mg/mL), however avoiding all disadvantages of discontinuous fermentation processes. At steady state, the total quantities of the synthesized EP after 48 h cultivation for the given equipment volume in D = 0.035 h-1 and D = 0.075 h-1 were 8.67 and 12 g, correspondingly, while it was 2.9 g for batch culture. Process parameters did not change after a ten-day run at D = 0.35 h-1. A degree of purity of EP fraction received from continuous cultures was significantly increased up to 93-96%. A lack of cytotoxicity and high cell viability were observed for human dermal fibroblast cells after 24 h incubation with crude EP from C. canadensis 28 and purified PGA fraction that could suggest its high potential for cosmetic applications.

High bioreactor production and emulsifying activity of an unusual exopolymer by Chromohalobacter canadensis 28.

Unusual composition of an exopolymer (EP) from an obligate halophilic bacterium Chromohalobacter canadensis 28 has triggered an interest in development of an effective bioreactor process for its production. Its synthesis was investigated in 2-L bioreactor at agitation speeds at interval 600-1000 rpm, at a constant air flow rate of 0.5 vvm; aeration rates of 0.5, 1.0, and 1.5 vvm were tested at constant agitation rate of 900 rpm. EP production was affected by both, agitation and aeration. As a result twofold increase of EP yield was observed and additionally increased up to 3.08 mg/mL in a presence of surfactants. For effective scale-up of bioreactors mass transfer parameters were estimated and lowest values of KLa obtained for the highest productivity fermentation was established. Emulsification activity of EP exceeded that of trade hydrocolloids xanthan, guar gum, and cellulose. A good synergism between EP and commercial cellulose proved its potential exploration as an enhancer of emulsifying properties of trade emulsions. A pronounced lipophilic effect of EP was established toward olive oil and liquid paraffin. Cultivation of human keratinocyte cells (HaCaT) with crude EP and purified γ-polyglutamic acid (PGA) showed higher viability than control group.

Levan-based hydrogels for controlled release of Amphotericin B for dermal local antifungal therapy of Candidiasis.

Hydrogels from Halomonas levan polysaccharide were prepared at different crosslinking densities. Swelling results demonstrated pH dependent rather than temperature dependent swelling of the hydrogel and the highest swelling value was achieved at basic conditions with a swelling ratio of 9.1 ± 0.1 which is the highest reported for levan based hydrogels. SEM images show a porous network architecture, which indicates a large surface area of the hydrogels. Rheological analyses showed the viscoelastic behavior of the hydrogels. Biocompatibility of the hydrogels was confirmed by cell culture experiments. For drug release experiments Amphotericin B (AmB) was used. 51% of the loaded AmB was released into the PBS buffer and the released AmB had a significant antifungal activity against Candida albicans.

Encapsulated melatonin in polycaprolactone (PCL) microparticles as a promising graft material.

Electrospraying assures many advantages with taking less time and costing less relatively to the other conventional particle production methods. In this research, we investigated the encapsulation of melatonin (MEL) hormone in polycaprolactone (PCL) microparticles by using electrospraying method. Morphology analysis of the produced particles completed with Scanning Electron Microscopy (SEM). SEM images demonstrated that micro-particles of 3 wt% PCL solution has the most suitable particle diameter size (2.3 ±â€¯0.64 µm) for melatonin encapsulation. According to the characterization of the particles, electrospraying parameters like optimal collecting distance, the flow rate of the solution and voltage of the system detected as 8 cm, 0.5 ml/h, and 10 kV respectively. For determining the chemical bonds of scaffold Fourier-Transform Infrared Spectroscopy (FTIR) were used and FTIR results showed that melatonin successfully loaded into PCL micro-particles. Drug release kinetics of the melatonin loaded particles indicated that melatonin released with a burst at the beginning and release behavior became sustainable over a period of 8 h with the encapsulation efficiency of about 73%. In addition, both in-vitro and in-vivo studies of the graft materials also completed. Primary human osteoblasts (HOB) cells and female Sprague Dawley rats were used in in-vitro and in-vivo studies. Test results demonstrate cell population, and bone volume of the rats grafted with composites has remarkably increased, this caused remodelling in bone structure. Overall, these findings indicate that encapsulation of melatonin in the PCL particles with electrospray method is optimum for new synthetic graft material.