The impact of anastomotic leakage characteristics on the occurrence of anastomotic stenosis after colorectal resection, a retrospective cohort study.

INTRODUCTION: Anastomotic stenosis (AS) is a common complication after colorectal resection. However, the predisposing factors for stricture formation are not fully understood. Previous studies have shown anastomotic leakage (AL) to be a risk factor for the occurrence of AS. Therefore, we aim to investigate the impact of anastomotic leakage characteristics on the occurrence of anastomotic stenosis after colorectal resection. METHODS: Consecutive patients with AL following elective, sphincter preserving, colorectal resection, with or without diversion ostomy, between January 2009 and March 2023 were identified from a prospectively collected database. The characteristics of the anastomotic leakage, patient baseline and operative characteristics as well as the postoperative outcomes were analyzed using univariate and multivariate logistic regression to identify factors associated with the occurrence of post-leakage AS. RESULTS: A total of 129 patients developed AL and met the inclusion criteria. Among these, 28 (21.7%) patients were diagnosed with post-leakage AS. There was a significantly higher frequency of patients with neoadjuvant radiotherapy (18% vs 3%; p = .026) and hand-sewn anastomoses (39% vs 17%; p = .011) within the AS group. Furthermore, the extent of the anastomotic defect was significantly higher in the AS group compared with the non-AS group (50%, IQR 27-71 vs. 20%, IQR 9-40, p = 0.011). Similar findings were observed between the study groups regarding age, sex, BMI, ASA score, medical comorbidities, diagnosis, surgical procedure, surgical approach (open vs. minimally invasive), and anastomotic fashioning (side-to-end vs. end-to-end). On multivariate analysis, the extent of the anastomotic defect (OR 1.01; 95% CI 1.00-1.03; p = 0.034) and hand-sewn anastomoses (OR 2.68; 95% CI 1.01-6.98; p = 0.043) were confirmed as independent risk factors for post-leakage AS. No correlation could be observed between the occurrence of post-leakage AS and the ISREC grading of AL, the anastomotic height or the management of AL. Time to ostomy reversal was significantly longer in the AS group (202d, IQR 169-275 vs. 318d IQR 192-416, p = 0.014). CONCLUSION: The extent of the anastomotic defect and hand-sewn anastomoses were confirmed as independent risk factors for the occurrence of post-leakage AS. No correlation could be observed between the ISREC grading of AL, the anastomotic height or AL management, and the occurrence of post-leakage AS.

Secretome of Adipose-Derived Stem Cells Cultured in Platelet Lysate Improves Migration and Viability of Keratinocytes.

Chronic wounds depict a silent epidemic challenging medical professionals worldwide. Regenerative medicine uses adipose-derived stem cells (ADSC) in promising new therapies. In this study, platelet lysate (PL) as a xenogen-free substitute for foetal bovine serum (FBS) in ADSC culture was used to create an ADSC secretome containing cytokines for optimal wound healing conditions. The ADSC secretome was tested on keratinocytes for migrational behaviour and viability. Therefore, human ADSC were characterized under FBS (10%) and PL (5% and 10%) substitution, regarding morphology, differentiation, viability, gene and protein expression. ADSC were then cultured in 5% PL and their secretome was used for stimulation of keratinocyte migration and viability. To enhance the effect, ADSC were treated with Epithelial Growth Factor (EGF, 100 ng/mL) and hypoxia (1% O2). In both PL and FBS groups, ADSC expressed typical stem cell markers. PL induced a significantly higher increase in cell viability compared to FBS substitution. ADSC secretome contained various beneficial proteins which enhance the wound healing capacity of keratinocytes. This could be optimized treating ADSC with hypoxia and EGF. In conclusion, the study shows that ADSC cultivated in 5% PL can effectively support wound healing conditions and can be considered as a promising new therapy for individual treatment of chronic wound disorders.

Design considerations for a novel shape-memory-plate osteosynthesis allowing for non-invasive alteration of bending stiffness.

Biomechanical stimuli play a major role in fracture healing. Changing the fixation stiffness through the course of healing might accelerate bone healing and prevent healing complications. Shape memory alloy (SMA) based implants were developed to allow for non-invasive stiffness alteration during the fracture healing process. To gain a deeper understanding of the implant functionality based on the alloy characteristics and geometric design, the mechanical properties of different shape memory alloys where mechanically characterized. SMA bone plates were manufactured and the structural bending stiffness of the implants was determined at different temperatures and configurations. The temperature required for complete recovery of shape after deformation increased continuously with increasing pseudo-plastic deformation in SMA probes. Full recovery was observed at temperatures ranging from 38°C to 52°C after pseudo-plastic deformations ranging from 0.2% to 1.0% outer fibre strain, respectively. The small fragment inverse-dynamisation implants revealed bending stiffnesses ranging from 0.09Nm2 to 0.34Nm2 in the initial state and from 0.16Nm2 to 0.46Nm2 after shape alteration. Dependent on the design, a relative gain of the implant stiffness ranging from 18.8% to 115.0% could be observed. The large inverse-dynamisation implants revealed bending stiffnesses from 3.7Nm2 to 7.1Nm2 before and 4.1Nm2 to 12.6Nm2 after triggering the shape memory effect. Dependent on the design a gain in stiffness from 11.8% to 117.2% was observed. Warming the SMA implant to 40°C for a short period of time, leads to a moderate increase in implant stiffness of up to 64.5%, while triggering the implant with 50°C leads to a maximum increase in stiffness of up to 127.3%. The Nitinol shape memory bone plates have a huge potential for improving the treatment of long shaft fractures by allowing for the increase, decrease or incremental change of implant stiffness in fracture stabilization. However, the interaction between design, material properties, and manufacturing processes need to be carefully considered for each specific application to achieve optimum function of SMA-based, stiffness altering, fracture-fixation implants.