Effect of Polyelectrolyte Charge Density on the Linear Viscoelastic Behavior and Processing of Complex Coacervate Adhesives.

It is well-known that the phase behavior and physicochemical and adhesive properties of complex coacervates are readily tuneable with the salt concentration of the medium. For toxicity reasons, however, the maximum applicable salt concentration in biomedical applications is typically low. Consequently, other strategies must be implemented in order to optimize the properties of the resulting complex coacervates. In this work, the effect of the charge density of a strong polyanion on the properties of complex coacervates was studied. To control this charge density, statistical anionic/charge-neutral hydrophilic copolymers were synthesized by means of an elegant protection/deprotection strategy and subsequently complexed with a strong polycation. The resulting complexes were observed to have an increasing water content as well as faster relaxation dynamics, with either increasing salt concentration or decreasing charge density. Time-salt and time-salt-charge density superpositions could be performed and showed that the relaxation mechanism of the complex coacervates remained unchanged. When the charge density was decreased, lower salt concentration complexes became suitable for viscoelastic adhesion with improved injectability. Such complex coacervates are promising candidates for injectable biomedical adhesives.

Hydrophobically modified complex coacervates for designing aqueous pressure-sensitive adhesives.

The rheology of complex coacervates can be elegantly tuned via the design and control of specific non-covalent hydrophobic interactions between the complexed polymer chains. The well-controlled balance between elasticity and energy dissipation makes complex coacervates perfect candidates for pressure-sensitive adhesives (PSAs). In this work, the polyanion poly(3-sulfopropyl methacrylate) (PSPMA) and the polycation quaternized poly(4-vinylpyridine) (QP4VP) were used to prepare complex coacervates in water. Progressive increase of hydrophobicity is introduced to the polyanion via partial deprotection of the protected precursor. Hence, the polymer chains in the complex coacervates can interact via both electrostatic (controlled by the amount of salt) and hydrophobic (controlled by the deprotection degree) interactions. It was observed that: (i) a rheological time-salt-hydrophobicity superposition principle is applicable, and can be used as a predictive tool for rheology, (ii) the slowdown of the stress relaxation dynamics, due to the increase of hydrophobic stickers (lower deprotection degree), can be captured by the sticky-Rouse model, and (iii) the systematic variation of hydrophobic stickers, amount of salt, and molecular weight of the polymers, enables the identification of optimizing parameters to design aqueous PSA systems. The presented results offer new pathways to control the rheology of complex coacervates and their applicability as PSAs.

Toward Effective and Adsorption-Based Antifouling Zipper Brushes: Effect of pH, Salt, and Polymer Design.

The undesired spontaneous deposition and accumulation of matter on surfaces, better known as fouling, is a problematic and often inevitable process plaguing a variety of industries. This detrimental process can be reduced or even prevented by coating surfaces with a dense layer of end-grafted polymer: a polymer brush. Producing such polymer brushes via adsorption presents a very attractive technique, as large surfaces can be coated in a quick and simple manner. Recently, we introduced a simple and scalable two-step adsorption strategy to fabricate block copolymer-based antifouling coatings on hydrophobic surfaces. This two-step approach involved the initial adsorption of hydrophobic-charged diblock copolymer micelles acting as a primer, followed by the complexation of oppositely charged-antifouling diblock copolymers to form the antifouling brush coating. Here, we significantly improve this adsorption-based zipper brush via systematic tuning of various parameters, including pH, salt concentration, and polymer design. This study reveals several key outcomes. First of all, increasing the hydrophobic/hydrophilic block ratio of the anchoring polymeric micelles (i.e., decreasing the hydrophilic corona) promotes adsorption to the surface, resulting in the most densely packed, uniform, and hydrophilic primer layers. Second, around a neutral pH and at a low salt concentration (1 mM), complexation of the weak polyelectrolyte (PE) blocks results in brushes with the best antifouling efficacy. Moreover, by tuning the ratio between these PE blocks, the brush density can be increased, which is also directly correlated to the antifouling performance. Finally, switching to different antifouling blocks can increase the internal density or strengthen the bound hydration layer of the brush, leading to an additional enhancement of the antifouling properties (>99% lysozyme, 87% bovine serum albumin).

Scalable Fabrication of Reversible Antifouling Block Copolymer Coatings via Adsorption Strategies.

Fouling remains a widespread challenge as its nonspecific and uncontrollable character limits the performance of materials and devices in numerous applications. Although many promising antifouling coatings have been developed to reduce or even prevent this undesirable adhesion process, most of them suffer from serious limitations, specifically in scalability. Whereas scalability can be particularly problematic for covalently bound antifouling polymer coatings, replacement by physisorbed systems remains complicated as it often results in less effective, low-density films. In this work, we introduce a two-step adsorption strategy to fabricate high-density block copolymer-based antifouling coatings on hydrophobic surfaces, which exhibit superior properties compared to one-step adsorbed coatings. The obtained hybrid coating manages to effectively suppress the attachment of both lysozyme and bovine serum albumin, which can be explained by its dense and homogeneous surface structure as well as the desired polymer conformation. In addition, the intrinsic reversibility of the adhered complex coacervate core micelles allows for the successful triggered release and regeneration of the hybrid coating, resulting in full recovery of its antifouling properties. The simplicity and reversibility make this a unique and promising antifouling strategy for large-scale underwater applications.

Strong Anionic/Charge-Neutral Block Copolymers from Cu(0)-Mediated Reversible Deactivation Radical Polymerization.

Despite recent developments in controlled polymerization techniques, the straightforward synthesis of block copolymers that feature both strong anionic and charge-neutral segments remains a difficult endeavor. In particular, solubility issues may arise during the direct synthesis of strong amphiphiles and typical postpolymerization deprotection often requires harsh conditions. To overcome these challenges, we employed Cu(0)-mediated reversible deactivation radical polymerization (Cu(0)-RDRP) on a hydrophobic isobutoxy-protected 3-sulfopropyl acrylate. Cu(0)-RDRP enables the rapid synthesis of the polymer, reaching high conversions and low dispersities while using a single solvent system and low amounts of copper species. These macromolecules are straightforward to characterize and can subsequently be deprotected in a mild yet highly efficient fashion to expose their strongly charged nature. Furthermore, a protected sulfonate segment could be grown from a variety of charge-neutral macroinitiators to produce, after the use of the same deprotection chemistry, a library of amphiphilic, double-hydrophilic as well as thermoresponsive block copolymers (BCPs). The ability of these various BCPs to self-assemble in aqueous media was further studied by dynamic light scattering, ζ-potential measurements as well as atomic force and electron microscopy.

Protected Poly(3-sulfopropyl methacrylate) Copolymers: Synthesis, Stability, and Orthogonal Deprotection.

Because of their permanent charge, strong polyelectrolytes remain challenging to characterize, in particular, when they are combined with hydrophobic features. For this reason, they are typically prepared through a postmodification of a fully hydrophobic precursor. Unfortunately, these routes often result in an incomplete functionalization or otherwise require harsh reaction conditions, thus limiting their applicability. To overcome these problems, in this work a strategy is presented that facilitates the preparation of well-defined strong polyanions by starting from protected 3-sulfopropyl methacrylate monomers. Depending on the chemistry of the protecting group, the hydrophobic precursor could be quantitatively converted into a strong polyanion under nucleophilic, acidic, or basic conditions. As a proof of concept, orthogonally protected diblock copolymers were synthesized, selectively deprotected, and allowed to self-assemble in aqueous solution. Further conversion into a fully water-soluble polyanion was achieved by deprotecting the second block as well.

Enhanced stability of complex coacervate core micelles following different core-crosslinking strategies.

Complex coacervate core micelles (C3Ms) are formed by mixing aqueous solutions of a charged (bio)macromolecule with an oppositely charged-neutral hydrophilic diblock copolymer. The stability of these structures is dependent on the ionic strength of the solution; above a critical ionic strength, the micelles will completely disintegrate. This instability at high ionic strengths is the main drawback for their application in, e.g., drug delivery systems or protein protection. In addition, the stability of C3Ms composed of weak polyelectrolytes is pH-dependent as well. The aim of this study is to assess the effectiveness of covalent crosslinking of the complex coacervate core to improve the stability of C3Ms. We studied the formation of C3Ms using a quaternized and amine-functionalized cationic-neutral diblock copolymer, poly(2-vinylpyridine)-block-poly(ethylene oxide) (QP2VP-b-PEO), and an anionic homopolymer, poly(acrylic acid) (PAA). Two different core-crosslinking strategies were employed that resulted in crosslinks between both types of polyelectrolyte chains in the core (i.e., between QP2VP and PAA) or in crosslinks between polyelectrolyte chains of the same type only (i.e., QP2VP). For these two strategies we used the crosslinkers 1-ethyl-3-(3'-dimethylaminopropyl)carbodiimide hydrochloride (EDC) and dimethyl-3,3'-dithiopropionimidate dihydrochloride (DTBP), respectively. EDC provides permanent crosslinks, while DTBP crosslinks can be broken by a reducing agent. Dynamic light scattering showed that both approaches significantly improved the stability of C3Ms against salt and pH changes. Furthermore, reduction of the disulphide bridges in the DTBP core-crosslinked micelles largely restored the original salt-stability profile. Therefore, this feature provides an excellent starting point for the application of C3Ms in controlled release formulations.

Hierarchical Self-Assembly of Supramolecular Double-Comb Triblock Terpolymers.

Involving supramolecular chemistry in self-assembling block copolymer systems enables design of macromolecular architectures that are challenging to obtain through conventional all-covalent routes. In this work we present supramolecular double-comb triblock terpolymers in which both outer blocks are able to interact with a surfactant via hydrogen bonding and thereby form a comb-shaped architecture upon complexation. While the neat triblock terpolymer only formed a triple lamellar morphology, multiple hierarchical structures were observed in these supramolecular comb-coil-comb triblock terpolymers by simply adjusting the surfactant concentration. Structures included spheres on tetragonally packed cylinders-in-lamellae and spheres on double parallel lamellae-in-lamellae, as evidenced by electron microscopy and X-ray scattering. Incorporation of a middle coil block thus allowed an even higher macromolecular complexity than the previously reported double-comb diblock copolymers.

Bioinspired Underwater Adhesives by Using the Supramolecular Toolbox.

Nature has developed protein-based adhesives whose underwater performance has attracted much research attention over the last few decades. The adhesive proteins are rich in catechols combined with amphiphilic and ionic features. This combination of features constitutes a supramolecular toolbox, to provide stimuli-responsive processing of the adhesive, to secure strong adhesion to a variety of surfaces, and to control the cohesive properties of the material. Here, the versatile interactions used in adhesives secreted by sandcastle worms and mussels are explored. These biological principles are then put in a broader perspective, and synthetic adhesive systems that are based on different types of supramolecular interactions are summarized. The variety and combinations of interactions that can be used in the design of new adhesive systems are highlighted.

The Origin of Hierarchical Structure Formation in Highly Grafted Symmetric Supramolecular Double-Comb Diblock Copolymers.

Involving supramolecular chemistry in self-assembling block copolymer systems enables design of complex macromolecular architectures that, in turn, could lead to complex phase behavior. It is an elegant route, as complicated and sensitive synthesis techniques can be avoided. Highly grafted double-comb diblock copolymers based on symmetric double hydrogen bond accepting poly(4-vinylpyridine)-block-poly(N-acryloylpiperidine) diblock copolymers and donating 3-nonadecylphenol amphiphiles are realized and studied systematically by changing the molecular weight of the copolymer. Double perpendicular lamellae-in-lamellae are formed in all complexes, independent of the copolymer molecular weight. Temperature-resolved measurements demonstrate that the supramolecular nature and ability to crystallize are responsible for the formation of such multiblock-like structures. Because of these driving forces and severe plasticization of the complexes in the liquid crystalline state, this supramolecular approach can be useful for steering self-assembly of both low- and high-molecular-weight block copolymer systems.

Hierarchical Layer Engineering Using Supramolecular Double-Comb Diblock Copolymers.

The formation of unusual multilayered parallel lamellae-in-lamellae in symmetric supramolecular double-comb diblock copolymers is presented. While keeping the concentration of surfactant fixed, the number of internal layers was found to increase with molecular weight M up to 34 for the largest block copolymer. The number of internal structures n was established to scale as M0.67 and therefore enables easy design of such structures with great precision.

Highly Ordered Structure Formation in RAFT-Synthesized PtBOS-b-P4VP Diblock Copolymers.

Linear poly(4-tert-butoxystyrene)-b-poly(4-vinylpyridine) (PtBOS-b-P4VP) diblock copolymers are synthesized using reversible addition-fragmentation chain transfer polymerization. The self-assembly of four different PtBOS-b-P4VP diblock copolymers is studied using small-angle X-ray scattering and transmission electron microscopy and a number of interesting observations are made. A tBOS62 -b-4VP28 diblock copolymer with a weight fraction P4VP of 0.21 shows a disordered morphology of P4VP spheres with liquid-like short-range order despite an estimated value of χN of the order of 50. Increasing the length of the 4VP block to tBOS62 -b-4VP199 results in a diblock copolymer with a weight fraction P4VP of 0.66. It forms a remarkably well-ordered lamellar structure. Likewise, a tBOS146 -b-4VP120 diblock copolymer with a weight fraction P4VP of 0.33 forms an extremely well-ordered hexagonal structure of P4VP cylinders. Increasing the P4VP block of this block copolymer to tBOS146 -b-4VP190 with a weight fraction P4VP of 0.44 results in a bicontinuous gyroid morphology despite the estimated strong segregation of χN≅150. These results are discussed in terms of the architectural dissimilarity of the two monomers, characterized by the presence of the large side group of PtBOS, and the previously reported value of the interaction parameter, χ≅0.39, for this polymer pair.