Enhanced Responsivity and Optoelectronic Properties of Self-Powered Solar-Blind Ag2O/ß-Ga2O3 Heterojunction-Based Photodetector with Ag:AZO Co-Sputtered Electrode.

A Ag:AZO electrode was used as an electrode for a self-powered solar-blind ultraviolet photodetector based on a Ag2O/ß-Ga2O3 heterojunction. The Ag:AZO electrode was fabricated by co-sputtering Ag and AZO heterogeneous targets using the structural characteristics of a Facing Targets Sputtering (FTS) system with two-facing targets, and the electrical, crystallographic, structural, and optical properties of the fabricated thin film were evaluated. A photodetector was fabricated and evaluated based on the research results that the surface roughness of the electrode can reduce the light energy loss by reducing the scattering and reflectance of incident light energy and improving the trapping phenomenon between interfaces. The thickness of the electrodes was varied from 20 nm to 50 nm depending on the sputtering time. The optoelectronic properties were measured under 254 nm UV-C light, the on/off ratio of the 20 nm Ag:AZO electrode with the lowest surface roughness was 2.01 × 108, and the responsivity and detectivity were 56 mA/W and 6.99 × 1011 Jones, respectively. The Ag2O/ß-Ga2O3-based solar-blind photodetector with a newly fabricated top electrode exhibited improved response with self-powered characteristics.

A Self-Powered High-Responsivity, Fast-Response-Speed Solar-Blind Ultraviolet Photodetector Based on CuO/ß-Ga2O3 Heterojunction with Built-In Potential Control.

Controlling built-in potential can enhance the photoresponse performance of self-powered photodetectors. Among the methods for controlling the built-in potential of self-powered devices, postannealing is simpler, more efficient, and less expensive than ion doping and alternative material research. In this study, a CuO film was deposited on a ß-Ga2O3 epitaxial layer via reactive sputtering with an FTS system, and a self-powered solar-blind photodetector was fabricated through a CuO/ß-Ga2O3 heterojunction and postannealed at different temperatures. The postannealing process reduced the defects and dislocations at the interface between each layer and affected the electrical and structural properties of the CuO film. After postannealing at 300 °C, the carrier concentration of the CuO film increased from 4.24 × 1018 to 1.36 × 1020 cm-3, bringing the Fermi level toward the valence band of the CuO film and increasing the built-in potential of the CuO/ß-Ga2O3 heterojunction. Thus, the photogenerated carriers were rapidly separated, increasing the sensitivity and response speed of the photodetector. The as-fabricated photodetector with 300 °C postannealing exhibited a photo-to-dark current ratio of 1.07 × 103; responsivity and detectivity of 30.3 mA/W and 1.10 × 1012 Jones, respectively; and fast rise and decay times of 12 ms and 14 ms, respectively. After three months of storage in an open-air space, the photocurrent density of the photodetector was maintained, indicating good stability with aging. These results suggest that the photocharacteristics of CuO/ß-Ga2O3 heterojunction self-powered solar-blind photodetectors can be improved through built-in potential control using a postannealing process.

The Properties of Microwave-Assisted Synthesis of Metal-Organic Frameworks and Their Applications.

Metal-organic frameworks (MOF) are a class of porous materials with various functions based on their host-guest chemistry. Their selectivity, diffusion kinetics, and catalytic activity are influenced by their design and synthetic procedure. The synthesis of different MOFs has been of considerable interest during the past decade thanks to their various applications in the arena of sensors, catalysts, adsorption, and electronic devices. Among the different techniques for the synthesis of MOFs, such as the solvothermal, sonochemical, ionothermal, and mechanochemical processes, microwave-assisted synthesis has clinched a significant place in MOF synthesis. The main assets of microwave-assisted synthesis are the short reaction time, the fast rate of nucleation, and the modified properties of MOFs. The review encompasses the development of the microwave-assisted synthesis of MOFs, their properties, and their applications in various fields.

Temperature-Dependent Self-Powered Solar-Blind Photodetector Based on Ag2O/ß-Ga2O3 Heterojunction.

In this study, a high-photoresponsivity self-powered deep ultraviolet (DUV) photodetector based on an Ag2O/ß-Ga2O3 heterojunction was fabricated by depositing a p-type Ag2O thin film onto an n-type ß-Ga2O3 layer. The device characteristics after post-annealing at temperatures ranging from 0 to 400 °C were investigated. Our DUV devices exhibited typical rectification characteristics. At a post-annealing temperature of 300 °C, the as-fabricated device had a low leakage current of 4.24 × 10-11 A, ideality factor of 2.08, and a barrier height of 1.12 eV. Moreover, a high photo-responsivity of 12.87 mA/W was obtained at a 100 µW/cm2 light intensity at a 254 nm wavelength at zero bias voltage, the detectivity was 2.70 × 1011 Jones, and the rise and fall time were 29.76, 46.73 ms, respectively. Based on these results, the Ag2O/ß-Ga2O3 heterojunction photodetector operates without an externally applied voltage and has high responsivity, which will help in the performance improvement of ultraviolet sensing systems.

Ag2O/ß-Ga2O3 Heterojunction-Based Self-Powered Solar Blind Photodetector with High Responsivity and Stability.

Self-powered deep-ultraviolet photodetectors have received considerable attention in recent years because of their efficiency, reliability, and various applications in civilian and military fields. Herein, a Ag/Ag2O layer is continuously deposited on a ß-Ga2O3 epitaxial layer by a facing target sputtering system without opening the chamber, which has an advantage in time and cost. A p-n junction photodetector was constructed through the Ag2O/ß-Ga2O3 heterojunction and by varying the thickness of the Ag film, which was controlled by the sputtering time. The effect of top electrode thickness on the photoresponse characteristics of photodetectors was studied. Because thin Ag films have low surface roughness, indicating low optical loss and good interfacial conditions, photodetectors using a thin Ag film as the top electrode exhibit high photoresponsivity. However, Ag films that were thinner than the threshold thickness, which is the minimum thickness required to form a continuous, homogeneous surface film, exhibited rather low performance owing to the high reflection and scattering caused by the inhomogeneous surface morphology. The as-fabricated photodetector with a 20 nm Ag film presents a high on/off ratio of 3.43 × 108, responsivity and detectivity of 25.65 mA/W and 6.10 × 1011 Jones, respectively, and comparable rise and decay times of 108 and 80 ms, respectively. Additionally, even after three months of storage in an ambient environment, the photoresponse of the photodetector was maintained, indicating good stability in air. These results suggest that Ag2O/ß-Ga2O3 heterojunction-based photodetectors with thin Ag films can be used in various applications requiring deep-ultraviolet detection without an external power supply.

Enhanced Hydrogen Production at Optimum pH for the Recovery Cycle of ß-FeOOH.

In the photo-Fenton reaction, highly reactive oxygen species are generated on UV irradiation of ß-FeOOH, which contributes significantly to hydrogen production. The production process was performed by adjusting the pH of the solution. The effect of acid concentration on hydrogen production was analyzed in this study, and the difference in the amount of hydrogen gas produced in each sample with different pH values was determined. X-ray powder diffraction (XRD) measurements of the samples corresponding to the peaks of ß-FeOOH were compared with the reference data, and crystallite sizes were calculated by the Scherrer equation using XRD patterns. The rod-like structure of the sample particles was revealed by scanning electron microscopy. A higher amount of hydrogen was produced at lower pH, and these results confirmed that pH plays an important role in hydrogen production.

Rod-Shaped ß-FeOOH Synthesis for Hydrogen Production under Light Irradiation.

Renewable energy is spotlighted as a resource to replace fossil fuels, and among the resources, active research on hydrogen energy is ongoing. Various methods have been developed to produce hydrogen energy using photoreduction processes. In this study, we synthesized ß-phase iron oxyhydroxide (ß-FeOOH) using a hydrothermal method with an optimal synthesis time and investigated its photofunctional properties, including hydrogen production. The obtained samples were characterized and compared with reference data. X-ray powder diffraction results corresponded to the peaks of the reference data. A rod structure was confirmed by scanning electron microscopy, and no impurities were observed. The band-gap energy of ß-FeOOH was calculated as 1.8-2.6 eV. A photoreduction process was performed based on a photo-Fenton reaction to produce hydrogen by irradiating ultraviolet (UV) on ß-FeOOH. The synthesized ß-FeOOH was subjected to UV irradiation for 24 h to produce hydrogen, and we confirmed that hydrogen was successfully produced. The properties of ß-FeOOH were evaluated after UV irradiation.

Characteristics of Aluminum-Doped Zinc Oxide Films Grown Using Facing Target Sputtering for Transparent Electrode of Heterojunction Solar Cells.

In general sputtering, material characteristics can be degraded by high-energy particles located inside the plasma owing to the thin film surface. However, facing target sputtering (FTS) can be used to produce high-quality thin films through maximum control over substrate damage and the reduction of layer damage caused by high-energy particles impacting the substrate. Transparent conductive oxides (TCOs) are being applied to a variety of technologies, including displays and solar cells. The typical transparent electrode material is indium tin oxide (ITO), which contains rare and expensive raw materials. Aluminum-doped zinc oxide (AZO) has attracted increasing attention as a substitute to ITO because it is composed of abundantly available resources and is generally inexpensive. In this study, an AZO thin film was prepared using an FTS system for heterojunction solar cells. The effects of the deposition substrate temperature on the resulting electrical conductivity, structural properties, and optical properties of the AZO thin films were examined.

Influence of Surface Morphology and Conductivity on Photocatalytic Performance of Solution-Processed Zinc Oxide Film.

Solution-processed ZnO films with various structures have been fabricated and the influence of surface morphology and conductivity on photocatalytic performance, including improvement of conductivity, hydrogen production, and photodegradation of rhodamine B, has been investigated. Surface morphology was controlled by solution conditions, and as-fabricated films had rod, dense, and flower-like structures. Improved conductivity was revealed by the photocatalytic activity of ZnO, the influence of surface morphology on the photodegradation of rhodamine B, and the relationship with conductivity and hydrogen production.

Agonistic induction of PPARγ reverses cigarette smoke-induced emphysema.

The development of emphysema in humans and mice exposed to cigarette smoke is promoted by activation of an adaptive immune response. Lung myeloid dendritic cells (mDCs) derived from cigarette smokers activate autoreactive Th1 and Th17 cells. mDC-dependent activation of T cell subsets requires expression of the SPP1 gene, which encodes osteopontin (OPN), a pleiotropic cytokine implicated in autoimmune responses. The upstream molecular events that promote SPP1 expression and activate mDCs in response to smoke remain unknown. Here, we show that peroxisome proliferator-activated receptor γ (PPARG/Pparg) expression was downregulated in mDCs of smokers with emphysema and mice exposed to chronic smoke. Conditional knockout of PPARγ in APCs using Cd11c-Cre Pparg(flox/flox) mice led to spontaneous lung inflammation and emphysema that resembled the phenotype of smoke-exposed mice. The inflammatory phenotype of Cd11c-Cre Pparg(flox/flox) mice required OPN, suggesting an antiinflammatory mechanism in which PPARγ negatively regulates Spp1 expression in the lung. A 2-month treatment with a PPARγ agonist reversed emphysema in WT mice despite continual smoke exposure. Furthermore, endogenous PPARγ agonists were reduced in the plasma of smokers with emphysema. These findings reveal a proinflammatory pathway, in which reduced PPARγ activity promotes emphysema, and suggest that targeting this pathway in smokers could prevent and reverse emphysema.

Dual protective mechanisms of matrix metalloproteinases 2 and 9 in immune defense against Streptococcus pneumoniae.

A localized and effective innate immune response to pathogenic bacterial invasion is central to host survival. Identification of the critical local innate mediators of lung defense against such pathogens is essential for a complete understanding of the mechanism(s) underlying effective host defense. In an acute model of Streptococcus pneumoniae lung infection, deficiency in matrix metalloproteinase (MMP)2 and MMP9 (Mmp2/9(-/-)) conferred a survival disadvantage relative to wild-type mice treated under the same conditions. S. pneumoniae-infected Mmp2/9(-/-) mice recruited more polymorphonuclear leukocytes to the lung but had higher bacterial burdens. Mmp2/9(-/-) mice showed significantly higher levels of IL-17A, IP-10, and RANTES in the lung. Although MMP2-dependent cleavage partially inactivated IL-17A, MMP9 was critical for effective bacterial phagocytosis and reactive oxygen species generation in polymorphonuclear neutrophils. These data demonstrate critical nonredundant and protective roles for MMP2 and MMP9 in the early host immune response against S. pneumoniae infection.

A3 adenosine receptor signaling influences pulmonary inflammation and fibrosis.

Adenosine is a signaling molecule produced during conditions that cause cellular stress or damage. This signaling pathway is implicated in the regulation of pulmonary disorders through the selective engagement of adenosine receptors. The goal of this study was to examine the involvement of the A(3) adenosine receptor (A(3)R) in a bleomycin model of pulmonary inflammation and fibrosis. Results demonstrated that A(3)R-deficient mice exhibit enhanced pulmonary inflammation that included an increase in eosinophils. Accordingly, there was a selective up-regulation of eosinophil-related chemokines and cytokines in the lungs of A(3)R-deficient mice exposed to bleomycin. This increase in eosinophil numbers was accompanied by a decrease in the amount of extracellular eosinophil peroxidase activity in lavage fluid from A(3)R-deficient mice exposed to bleomycin, an observation suggesting that the A(3)R is necessary for eosinophil degranulation in this model. Despite an increase in inflammatory metrics associated with A(3)R-deficient mice treated with bleomycin, there was little difference in the degree of pulmonary fibrosis. Examination of fibrotic mediators demonstrated enhanced transforming growth factor (TGF)-beta1 expression, but not a concomitant increase in TGF-beta1 activity. This was associated with the loss of expression of matrix metalloprotease 9, an activator of TGF-beta1, in alveolar macrophages and airway mast cells in the lungs of A(3)R-deficient mice. Together, these results suggest that the A(3)R serves antiinflammatory functions in the bleomycin model, and is also involved in regulating the production of mediators that can impact fibrosis.