Investigation of Photocatalytic PVDF Membranes Containing Inorganic Nanoparticles for Model Dairy Wastewater Treatment.

Membrane separation processes are promising methods for wastewater treatment. Membrane fouling limits their wider use; however, this may be mitigated using photocatalytic composite materials for membrane preparation. This study aimed to investigate photocatalytic polyvinylidene fluoride (PVDF)-based nanocomposite membranes for treating model dairy wastewater containing bovine serum albumin (BSA). Membranes were fabricated via physical coating (with TiO2, and/or carbon nanotubes, and/or BiVO4) and blending (with TiO2). Another objective of this study was to compare membranes of identical compositions fabricated using different techniques, and to examine how various TiO2 concentrations affect the antifouling and cleaning performances of the blended membranes. Filtration experiments were performed using a dead-end cell. Filtration resistances, BSA rejection, and photocatalytic cleanability (characterized by flux recovery ratio (FRR)) were measured. The surface characteristics (SEM, EDX), roughness (measured by atomic force microscopy, AFM), wettability (contact angle measurements), and zeta potential of the membranes were also examined. Coated PVDF membranes showed higher hydrophilicity than the pristine PVDF membrane, as evidenced by a decreased contact angle, but the higher hydrophilicity did not result in higher fluxes, unlike the case of blended membranes. The increased surface roughness resulted in increased reversible fouling, but decreased BSA retention. Furthermore, the TiO2-coated membranes had a better flux recovery ratio (FRR, 97%) than the TiO2-blended membranes (35%). However, the TiO2-coated membrane had larger total filtration resistances and a lower water flux than the commercial pristine PVDF membrane and TiO2-blended membrane, which may be due to pore blockage or an additional coating layer formed by the nanoparticles. The BSA rejection of the TiO2-coated membrane was lower than that of the commercial pristine PVDF membrane. In contrast, the TiO2-blended membranes showed lower resistance than the pristine PVDF membrane, and exhibited better antifouling performance, superior flux, and comparable BSA rejection. Increasing the TiO2 content of the TiO2-blended membranes (from 1 to 2.5%) resulted in increased antifouling and comparable BSA rejection (more than 95%). However, the effect of TiO2 concentration on flux recovery was negligible.

A comparative study of femtosecond pulsed laser ablation of meloxicam in distilled water and in air.

The increasing prevalence of water insoluble or poorly soluble drugs calls for the development of new formulation methods. Common approaches include the reduction of particle size and degree of crystallinity. Pulsed laser ablation is a clean technique for producing sub-micrometre sized drug particles and has the potential to induce amorphization. We studied the effect of femtosecond pulsed laser ablation (ELI ALPS THz pump laser system: λc = 781 nm, τ = 135 fs) on meloxicam in distilled water and in air. The ablated particles were characterized chemically, morphologically and in terms of crystallinity. We demonstrated that femtosecond laser ablation can induce partial amorphization of the particles in addition to a reduction in particle size. In the case of femtosecond pulsed laser ablation in air, the formation of pure meloxicam spheres showed that this technique can produce amorphous meloxicam without the use of excipients, which is a unique result. We also aimed to describe the ablation processes in both investigated media.

A comprehensive analysis of meloxicam particles produced by nanosecond laser ablation as a wet milling technique.

Recently, the number of water insoluble and poorly soluble drug compounds has increased significantly. Therefore, growing interest has been witnessed in different particle size reduction techniques to improve the dissolution rates, transport characteristics and bioavailability of drugs. Laser ablation has proven to be an alternative method to the production of nano- and micrometre-sized drug particles without considerable chemical damage. We present the nanosecond laser ablation of drug pastilles in distilled water, targeting meloxicam, a poorly water soluble nonsteroidal anti-inflammatory drug, at different laser wavelengths (248 nm, 532 nm and 1064 nm). Besides chemical characterization, crystallinity, morphology and particle size studies, the mechanism of the particle generation process was examined. The applicability of ablated particles in drug formulation was investigated by solubility, cytotoxicity and anti-inflammatory effect measurements. We showed that laser ablation is a clean, efficient and chemically non-damaging method to reduce the size of meloxicam particles to the sub-micrometre-few micrometre size range, which is optimal for pulmonary drug delivery. Complemented by the excellent solubility (four to nine times higher) and anti-inflammatory (four to five times better) properties of the particles compared to the initial drug, laser ablation is predicted to have wider applications in the development of drug formulations.

Development of extra-fine particles containing nanosized meloxicam for deep pulmonary delivery: In vitro aerodynamic and cell line measurements.

Pulmonary drug administration provides a platform for the effective local treatment of various respiratory diseases. Application of nano-sized active ingredients results in higher bioavailability because of their large specific surface area. Extra-fine dry powder inhalers reach the smaller airways, further improving therapeutic efficiency. Poorly water-soluble meloxicam was the selected active ingredient. We aimed to decrease the particle size into the nano range by wet milling and producing extra-fine inhalable particles via nano spray-drying. The diameter of the drug was reduced to 138 nm. The particle size of the dry products was between 1.1 and 1.5 µm, and the dispersed diameter was between 500 and 800 nm. Owing to the excipients (poly-vinyl-alcohol, leucine), the spray-dried particles presented nearly spherical morphology. The drug became partially amorphous. Thanks to the improved surface area, the solubility and the released and the diffused amount of the meloxicam increased in artificial lung media. The in vitro aerodynamic measurements showed that the leucine-containing formulations had outstanding fine particle fraction (FPF) deposition with 1.3 µm mass median aerodynamic diameter (MMAD). The aerodynamic particle counter test also proved the extra-fine aerodynamic particle size. The in vitro cell line experiments revealed the non-cytotoxicity of the products and the suppression of the interleukin concentration. Overall, the powders are suitable for deep pulmonary delivery and the local treatment of lung inflammations.

Mixed scattering as a problem in laser speckle contrast analysis.

Static scattering is detrimental to the accuracy of laser speckle contrast analysis (LASCA) measurements on skin when, instead of percentile change monitoring, absolute perfusion values are needed, e.g., for tissue injury examination. Perfusion values were calculated using two evaluation models, while changing the dynamic/static scattering ratio of monitored skin and tissue phantoms. Results were strongly affected by the significant increase of static contribution. Measurements on a modified tissue phantom showed that the changes in the measured perfusion values were mostly caused by the mixed scattering, which was omitted by the tested models. Dynamic ratio values obtained by multi-exposure LASCA could be used for perfusion data correction.

Anti-counterfeiting protection, personalized medicines - Development of 2D identification methods using laser technology.

Counterfeiting of the products for healing is as old as trading, and it is difficult to quantify the magnitude of the problem. It is known that substandard and/or falsified (SF) medicines are a growing global threat to health, and they cause serious social and economic damage. The EU has a strong legal framework for medicines, it is mandatory to meet the requirements of Directive 2011/62/EU. Serialisation prevents SF medicinal products from entering the legal distribution chain. The present study is an extension of the original idea and aims to develop a laser technology-based method to mark an individual traceable code on the surface of the tablet, which technology can also be used for marking personalized medicines. The method is based on the ablation of the upper layer of a double-layer, differently coloured coating. The 2D code should be formed without harming the functional layer, and anyone with a smartphone integrated with a camera should be able to authenticate these drugs with a suitable application. The present findings confirmed that KrF excimer laser and Ti:sapphire femtosecond laser are efficient and reliable for marking. These should be promising candidates for pharmaceutical companies that would like to have additional protection against drug counterfeiters.

Fabrication of Submicrometer-Sized Meloxicam Particles Using Femtosecond Laser Ablation in Gas and Liquid Environments.

In pharmaceutical development, more and more drugs are classified as poorly water-soluble or insoluble. Particle size reduction is a common way to fight this trend by improving dissolution rate, transport characteristics and bioavailability. Pulsed laser ablation is a ground-breaking technique of drug particle generation in the nano- and micrometer size range. Meloxicam, a commonly used nonsteroidal anti-inflammatory drug with poor water solubility, was chosen as the model drug. The pastille pressed meloxicam targets were irradiated by a Ti:sapphire laser (τ = 135 fs, λc = 800 nm) in air and in distilled water. Fourier transform infrared and Raman spectroscopies were used for chemical characterization and scanning electron microscopy to determine morphology and size. Additional particle size studies were performed using a scanning mobility particle sizer. Our experiments demonstrated that significant particle size reduction can be achieved with laser ablation both in air and in distilled water without any chemical change of meloxicam. The size of the ablated particles (~50 nm to a few microns) is approximately at least one-tenth of the size (~10-50 micron) of commercially available meloxicam crystals. Furthermore, nanoaggregate formation was described during pulsed laser ablation in air, which was scarcely studied for drug/organic molecules before.

Full range tuning of the composition of Au/Ag binary nanoparticles by spark discharge generation.

Gold/silver bimetallic nanoparticles still attract extensive interest due to their favorable properties e.g. in plasmonics or catalysis. We present here a facile and robust way for the production of clean Au/Ag binary nanoparticles (BNPs) with a total control over the composition via the spark discharge nanoparticle generation technique. With the application of pure Ag and Au electrodes, a tuning range of 55 to 90% Au content was achieved, but this can be further extended to the full 0 to 100% range by using a couple of alloyed electrodes. An added benefit of the approach is that either the concentration or the mean particle size can be kept constant at every composition by adjusting the generator parameters. Based on the systematic experimental data collected, a semi-empirical model for the prediction of the Au/Ag BNP composition was also developed. This model was used to calculate the theoretically achievable Au/Ag composition at a given spark parameter set in the parameter range most commonly used in the literature.

Application of pulsed laser ablation (PLA) for the size reduction of non-steroidal anti-inflammatory drugs (NSAIDs).

We studied the application of pulsed laser ablation (PLA) for particle size reduction in non-steroidal anti-inflammatory drugs (NSAIDs). Grinding of the poorly water-soluble NSAID crystallites can considerably increase their solubility and bioavailability, thereby the necessary doses can be reduced significantly. We used tablets of ibuprofen, niflumic acid and meloxicam as targets. Nanosecond laser pulses were applied at various wavelengths (KrF excimer laser, λ = 248 nm, FWHM = 18 ns and Nd:YAG laser, λ1 = 532 nm/λ2 = 1064 nm, FWHM = 6 ns) and at various fluences. FTIR and Raman spectra showed that the chemical compositions of the drugs had not changed during ablation at 532 nm and 1064 nm laser wavelengths. The size distribution of the ablated products was established using two types of particle size analyzers (SMPS and OPC) having complementary measuring ranges. The mean size of the drug crystallites decreased from the initial 30-80 µm to the submicron to nanometer range. For a better understanding of the ablation mechanism we made several investigations (SEM, Ellipsometry, Fast photography) and some model calculations. We have established that PLA offers a chemical-free and simple method for the size reduction of poorly water-soluble drugs and a possible new way for pharmaceutical drug preformulation for nasal administration.

Hot-Band Anti-Stokes Fluorescence Properties of Alexa Fluor 568.

Hot-band absorption and anti-Stokes emission properties of an organic fluorescent dye, Alexa Fluor 568, were characterized and compared with those of Rhodamine 101. The comparison of the properties (e.g., quantum efficiency, spectral distribution, thermal properties, and fluorescence lifetime) between the two dyes confirms that both dyes undergo the same process when excited in the red spectral region. Possible undesirable crosstalk effects and applications in dSTORM microscopy were demonstrated and discussed.

Age-Related Absorption of the Human Lens in the Near-Ultraviolet Range.

The purpose of the present study was to determine the age dependence of the ultraviolet (UV) absorption of the different parts of the human crystalline lens. Cryostat sections of human cadaveric lenses (60 µm) were cut. The UV absorbance of nine samples, derived from different parts of the lens, was determined using a Shimadzu scanning spectrophotometer. The absorbance of the anterior and posterior lens capsules was measured separately. The absorption coefficients were calculated from the measured absorbance and values taken at 280 as well as at 360 nm were compared statistically. ANCOVA analysis of the values taken at 280 and at 360 nm wavelengths shows that correlation between the absorption coefficients and age can be found only in the case of the posterior layers. These results suggest a differential age-dependent increase of the UV absorption of the posterior layers compared to the anterior ones and can be related to the differential protein expression in the anterior and posterior parts. Posterior crystalline lens capsules have higher absorption coefficients than the anterior ones regardless of age.

Comparison of conventionally and naturally coloured coatings marked by laser technology for unique 2D coding of pharmaceuticals.

Substandard and/or falsified medicines are a growing global threat for health and they cause serious social and economic damage. In low- and middle-income countries the failure rate of these medical products is approximately 10.5%. 50% of medicines purchased over the Internet may be fake. According to Directive 2011/62/EU as regards the prevention of falsified medicines from entering into the legal supply chain, a unique identification should be put on each box of drugs in the EU from 9th February 2019. The current project is focusing on the development of a laser technology to mark an individual traceable code on the surface of the tablet. Usually, coatings contain titanium dioxide for sufficient coverage, which makes precision laser coding more difficult. New naturally coloured films do not include those excipients. In this research, we would like to compare the physical-chemical properties of conventionally and naturally coloured coatings after the laser marking procedure by using two types of lasers. This unique identification technology can be used for marking personalized medicine with the doses tailored for each patient, too. To sum up, the present findings may contribute to efficient and reliable laser marking solutions in the unique identification procedure. Based on our measurement results, it can be stated that excimer UV lasers are promising candidates as marking instruments for the polymer film in both conventionally and naturally coloured coatings.

Attachment and proliferation of human osteoblast-like cells (MG-63) on laser-ablated titanium implant material.

Demand is increasing for shortening the long (3-6 months) osseointegration period to rehabilitate patients' damaged chewing apparatus in as short a time as possible. For dental implants, as for biomaterials in general, the bio- and osseointegration processes can be controlled at molecular and cellular levels by modification of the implant surface. One of the most promising of such surface modifications is laser ablation, as demonstrated by our previous results [46]. Commercially pure (CP4) sand-blasted, acid-etched titanium disks (Denti® System Ltd., Hungary) were irradiated with a KrF excimer laser (248 nm, fluence 0.4 J/cm(2), FWHM 18 ns, 2000 pulses), or with a Nd:YAG laser (532 nm, 1.3 J/cm(2), 10 ns, 200 pulses) then examined by SEM, AFM, and XPS. In vitro attachment (24 h) and proliferation (72 h) of MG-63 osteoblast cells were investigated via dimethylthiazol-diphenyl tetrazolium bromide (MTT), alamarBlue (AB) assays alkaline phosphatase quantification (ALP) and SEM. SEM and AFM revealed significant changes in morphology and roughness. XPS confirmed the presence of TiO2 on each sample; after Nd:YAG treatment a reduced state of Ti (Ti(3+)) was also observed. MTT, AB and ALP measurements detected an increase in the number of cells between the 24- and 72 hour observations; however, laser treatment did not affect cell attachment and proliferation significantly.

The molecular background of the differential UV absorbance of the human lens in the 240-400 nm range.

The ultraviolet (UV) absorption of various sections of the human lens was studied and compared with protein expression paralleling differential UV absorbance in anterior and posterior lenticular tissue. The UV absorbance of serial lens cryostat sections (60 µm) and that of lens capsules was determined using a Shimadzu scanning spectrophotometer, and the absorption coefficients were calculated. Two-dimensional gel electrophoresis was performed using two pooled lenticular protein extracts (anterior and posterior sections). Protein spots were quantified and significantly different spots were identified by mass spectrometry following in-gel digestion with trypsin and chymotrypsin. The UV-C and UV-B absorption of the human lens increased toward the posterior parts of the lens. The anterior and posterior lens capsules also effectively absorbed UV radiation. Levels of molecular chaperone proteins Beta-crystallin B2 (UniProtKB ID:P43320), A3 (UniProtKB ID:P05813) and of glyceraldehyde 3-phosphate dehydrogenase (UniProtKB ID:P04406) were significantly higher in the anterior part of the lens, whereas lens proteins Beta-crystallin B1 (UniProtKB ID:P53674) and Alpha-crystallin A chain (UniProtKB ID:P02489) were higher in the posterior sections. These results provide evidence that differential UV absorption in the anterior and posterior lens is accompanied by differential protein expression.

Evaluation of laser-speckle contrast image analysis techniques in the cortical microcirculation of piglets.

A new laser speckle-contrast analysis (LASCA) technique based on multi-exposure imaging was employed to simultaneously study pial arteriolar responses with cerebrocortical perfusion changes to various vasodilator (5-10% CO(2) ventilation, bradykinin (1-10 µM), N-methyl-D-aspartate (100 µM)) vasoconstrictor (10-100 µM noradrenaline, 1M KCl), or neutral (2.1% H(2) ventilation) stimuli as well as to asphyxia in the newborn piglet. Anesthetized, ventilated animals (n=20) were fitted with closed cranial windows. Multiple exposure laser-speckle image series (1-100 ms) were obtained using a near infrared diode laser (λ=808 nm). The autocorrelation decay time (τ) of speckle fluctuations was determined over pial arterioles and parenchymal areas to express 1/τ being proportional to blood flow velocity by two different LASCA techniques: our novel multi-exposure or a single exposure (2 and 20 ms) approach. 1/τ values yielded by different LASCA techniques were not significantly different at most points. LASCA easily detected both increases and decreases in cortical blood flow (CoBF). Cortical 1/τ changes to hypercapnia closely matched quantitative CoBF data determined previously, and were also in accordance with increases of pial arteriolar blood flow, calculated from arteriolar flow velocity and cross sectional area changes. In summary, LASCA emerges as an appealing method to simultaneously study microvascular reactivity and cortical perfusion changes in the piglet.

Real correlation time measurement in laser speckle contrast analysis using wide exposure time range images.

In laser speckle contrast analysis (LASCA) used for imaging of blood flow, besides the moving blood cells, the speckle pattern is also influenced by the imaging system and scattering properties of the laser-illuminated static surface. A latex microsphere (650 nm size) emulsion was covered with scattering semitransparent materials (Teflon foils, tracing paper). Speckle images were recorded with different exposure times (0.2 ms-500 ms), and correlation times were determined by parameterizing the theoretical contrast-exposure time function. The correlation times obtained for covered and uncovered microsphere emulsions were in good agreement. The possibility of obtaining comparable, setup-independent results in blood perfusion monitoring can contribute to better applicability of LASCA.

Morphology and N2 permeability of multi-wall carbon nanotube--Teflon membranes.

We prepared buckypapers with surface densities in the 1.13-5.66 mg x cm(-2) range by filtering multi-wall carbon nanotube (MWCNT) suspensions in acetyl-acetone (acac) and dimethylformamide (DMF) through 0.45 microm nylon filters. Filtration curves were evaluated using the Carman equation. The average resistance of the filter itself was found to be Rm = 3.79 x 10(10) m(-1) for acac and 8.49 x 10(10) m(-1) for DMF The specific resistance a of the filter cakes decreased with increasing film surface density from 16.1 x 10(12) m x kg(-1) (for the 1.13 mg x cm(-2) film from DMF) to 4.38 x 10(12) m x kg(-1) (for the 5.66 mg x cm(-2) film from DMF). The effective diffusivity of N2 at 298 K and a pressure difference of 10 mbar was also determined for all membranes and found to fall into the 1.14 x 10(-9)-3.74 x 10(-9) m2 x s(-1) range. Both the porosity and the tortuosity of buckypapers increased with their thickness. An approx. 5 microm thick Teflon (PTFE) coating was applied to the MWCNT membranes by pulsed laser deposition. The gas permeability of the MWCNT-PTFE membranes matches that of the uncoated nanotube films. This observation is an agreement with our SEM and AFM data on porous coating morphology.

Fabrication of 150 nm period grating in fused silica by two-beam interferometric laser induced backside wet etching method.

Fused silica gratings with periods of 154 nm, 266 nm, and 550 nm have been fabricated by the method of two-beam interferometric laser induced backside wet etching (TWIN-LIBWE). The spatially filtered pulses at 266nm were splitted into two parts and interfered at an incident angle of 60(o), 30(o), and 14(o), respectively, on the backside surface of a fused silica plate contacting with the liquid absorber. The morphology of the etched gratings was characterized by atomic force microscope. According to our knowledge, the produced 154 nm period is the smallest grating constant generated by laser techniques directly in fused silica at present.

Survival and proliferative ability of various living cell types after laser-induced forward transfer.

The survival, proliferation, and differentiation of freshly isolated and cultured cells were studied after absorbing film-assisted laser-induced forward transfer. Rat Schwann and astroglial cells and pig lens epithelial cells were used for transfer and the cells were cultured for 2 weeks after laser-pulsed transfer. All three cell types survived, proliferated, and differentiated under cell culture conditions and regained their original phenotype a few days after cell transfer. Time resolution studies have shown that the time required to accelerate the jets and droplets containing the cells was less than 1 micros and that the estimated minimum average acceleration of those ejected cells that reached a constant velocity was approximately 10(7) x g. This suggests that the majority of studied cells tolerated the extremely high acceleration at the beginning of the ejection and the deceleration during impact on the acceptor plate without significant damage to the original phenotype. These results suggest that the absorbing film-assisted laser-induced forward transfer technique appears to be suitable for several potential applications in tissue engineering and the biomedical tissue repair technologies.

UV absorbance of the human cornea in the 240- to 400-nm range.

PURPOSE: To determine the UV absorbance of the corneal layers (epithelium, Bowman layer, stroma) in the 240- to 400-nm range. METHODS: Consecutive slices (100 microm) of human cadaveric corneas were cut, and the UV absorbance of each sample was determined in a scanning spectrophotometer. In some cases the epithelium was scraped off and its absorbance measured separately. RESULTS: The investigation of the UV-B absorption of consecutive corneal slices revealed evidence that UV-B absorption is 1.8 times higher in the anterior 100 microm of the human cornea than in the posterior layers. The UV absorbance of the posterior layers was uniform, showing no further structural dependence. The epithelium and Bowman layer are both effective absorbers of UV-B radiation. CONCLUSIONS: These results suggest that the anterior corneal layers are particularly important in preventing damage by UV-B radiation.