RESUMO
Three-dimensional porous carbon is considered as an ideal electrode material for supercapacitors (SCs) applications owing to its good conductivity, developed pore structure, and excellent connectivity. Herein, using longan shell as precursor, 3-dimensional porous carbon with abundant and interconnected pores and moderate heteroatoms were obtained via simple carbonization and potassium hydroxide (KOH) activation treatment. The electrochemical performances of obtained 3-dimensional porous carbon were investigated as electrode materials in symmetric SCs with aqueous and solid electrolytes. The optimized material that is named after longan shell 3-dimensional porous carbon 800 (LSPC800) possesses high porosity (1.644 cm3 g-1) and N content (1.14 at %). In the three-electrode measurement, the LSPC800 displays an excellent capacitance value of 359 F g-1. Besides, the LSPC800 also achieves splendid specific capacitance (254 F g-1) in the two electrode system, while the fabricated SC employing 1 M Li2SO4 as electrolyte acquires ultrahigh power density (15930.38 W kg-1). Most importantly, LSPC800 electrodes are further applied into the SC adopting the KOH/polyvinyl alcohol (PVA) gel electrolyte, which reaches up to an outstanding capacitance of 313 F g-1 at 0.5 A g-1. In addition, for the all-solid-state SC, its rate capability at 50 A g-1 is 72.73% and retention at the 10,000th run is 93.64%. Evidently, this work is of great significance to the simple fabrication of 3-dimensional porous carbon and further opens up a way of improving the value-added utilization of biomass materials, as well as proving that the biomass porous carbons have immense potential for high-performance SCs application.
RESUMO
Low-cost and earth-abundant coal has been considered to have a unique structural superiority as carbon sources of carbon quantum dots (CQDs). However, it is still difficult to obtain CQDs from raw coal due to its compactibility and lower reactivity, and the majority of the current coal-based CQDs usually emit green or blue fluorescence. Herein, a facile two-step oxidation approach (K2FeO4 pre-oxidation and H2O2 oxidation) was proposed to fabricate bandgap tunable CQDs from anthracite. The K2FeO4 pre-oxidation can not only weaken the non-bonding forces among coal molecules which cause the expansion of coal particles, but also form a large number of active sites on the surface of coal particles. The above effects make the bandgap tunable CQDs (blue, green, or yellow fluorescence) can be quickly obtained from anthracite within 1 h in the following H2O2 oxidation by simply adjusting the concentration of H2O2. All the as-prepared CQDs contain more than 30 at% oxygen, and the average diameters of which are <10 nm. The results also indicate that the high oxygen content only can create new energy states inside the band gap of CQDs with average diameter more than 3.2 ± 0.9 nm, which make the as-prepared CQDs emit green or yellow fluorescence.
RESUMO
A novel approach is developed to synthesize a nitrogen-doped porous Co3O4/anthracite-derived graphene (Co3O4/AG) nanocomposite through a combined self-assembly and heat treatment process using resource-rich anthracite as a carbonaceous precursor. The nanocomposite contains uniformly distributed Co3O4 nanoparticles with a size smaller than 8 nm on the surface of porous graphene, and exhibits a specific surface area (120 m2·g-1), well-developed mesopores distributed at 3~10 nm, and a high level of nitrogen doping (5.4 at. %). These unique microstructure features of the nanocomposite can offer extra active sites and efficient pathways during the electrochemical reaction, which are conducive to improvement of the electrochemical performance for the anode material. The Co3O4/AG electrode possesses a high reversible capacity of 845 mAh·g-1 and an excellent rate capacity of 587 mAh·g-1. Furthermore, a good cyclic stability of 510 mAh·g-1 after 100 cycles at 500 mA·g-1 is maintained. Therefore, this work could provide an economical and effective route for the large-scale application of a Co3O4/AG nanocomposite as an excellent anode material in lithium-ion batteries.
RESUMO
Coal tar pitch (CTP), a by-product of coking industry, has a unique molecule structure comprising an aromatic nucleus and several side chains bonding on this graphene-like nucleus, which is very similar to the structure of graphene quantum dots (GQDs). Based on this perception, we develop a facile approach to convert CTP to GQDs only by oxidation with hydrogen peroxide under mild conditions. One to three graphene layers, monodisperse GQDs with a narrow size distribution of 1.7 ± 0.4 nm, are obtained at high yield (more than 80 wt. %) from CTP. The as-produced GQDs are highly soluble and strongly fluorescent in aqueous solution. This simple strategy provides a feasible route towards the commercial synthesis of GQDs for its cheap material source, green reagent, mild condition, and high yield.
RESUMO
A novel carboxymethyl cellulose (CMC)-supported graphene oxide aerogel (CGOA) was fabricated from a cost-effective and abundant bituminous coal by a mild hydrothermal process and freeze-drying treatment. Such an aerogel has cross-linked graphene oxide layers supported by CMC, and therefore, displays high mechanical strength while having ultra-low density (8.257 mg·cm-3). The CGOA has a 3D interconnected porous structure, beneficial graphene framework defects and abundant oxygen-containing functional groups, which offer favorable diffusion channels and effective adsorption sites for the transport and adsorption of dye molecules. The adsorption performance of rhodamine B by an optimized CGOA shows a maximum monolayer adsorption capacity of 312.50 mg·g-1, as determined by Langmuir isotherm parameters. This CGOA exhibited a better adsorption efficiency (99.99%) in alkaline solution, and satisfactory stability (90.60%) after three cycles. In addition, adsorption experiments on various dyes have revealed that CGOA have better adsorption capacities for cationic dyes than anionic dyes.
RESUMO
The conventional synthesis route of graphene oxide (GOG), based on Hummers method, suffers from explosion risk, environmental concerns and a tedious synthesis process, which increases production costs and hinders its practical applications. Herein, we report a novel strategy for preparing few-layer graphene oxide (GOH) from humic acid via simple hydrothermal treatment. The formation of GOH is mainly attributed to the hydrolysis, oxidation and aromatization of humic acid under hydrothermal conditions. The as-prepared few-layer GOH has typical morphology (thin and crumpled sheets with the thickness of ~3.2 nm), crystal structure (a Raman ID/IG ratio of 1.09) and chemical composition (an X-ray Photoelectron Spectroscopy (XPS) O/C atomic ratio of 0.36) of few-layer GOG. The thermally reduced GOH (r-GOH) delivers considerable area capacitance of 28 µF·cm-2, high rate capability and low electrochemical resistance as supercapacitor electrodes. The described hydrothermal process shows great promise for the cheap, green and efficient synthesis of few-layer graphene oxide for advanced applications.