Near-Field Microwave Imaging Method of Monopole Antennas Based on Nitrogen-Vacancy Centers in Diamond.

Visualizing the near-field distribution of microwave field in a monopole antenna is very important for antenna design and manufacture. However, the traditional method of measuring antenna microwave near field distribution by mechanical scanning has some problems, such as long measurement time, low measurement accuracy and large system volume, which seriously limits the measurement effect of antenna microwave near field distribution. In this paper, a method of microwave near-field imaging of a monopole antenna using a nitrogen-vacancy center diamond is presented. We use the whole diamond as a probe and camera to achieve wide-field microwave imaging. Because there is no displacement structure in the system, the method has high time efficiency and good stability. Compared with the traditional measurement methods, the diamond probe has almost no effect on the measured microwave field, which realizes the accurate near-field imaging of the microwave field of the monopole antenna. This method achieves microwave near-field imaging of a monopole antenna with a diameter of 100 µm and a length of 15 mm at a field of view of 5 × 5 mm, with a spatial resolution of 3 µm and an imaging bandwidth of 2.7~3.2 GHz, and an optimal input microwave phase resolution of 0.52° at a microwave power of 0.8494 W. The results provide a new method for microwave near-field imaging and measurement of monopole antennas.

A bio-inspired two-stage bionic drag reduction method.

Reducing the surface resistance of underwater vehicles plays an important role in improving cruising speed and cruising mileage. The epidermis of loaches is not only covered with a layer of scale structure but also secretes mucus tissue with a lubricating effect, which makes loaches swim rapidly in muddy water. Study the morphology and structure of the skin of loach and establish a two-stage biomimetic drag reduction model. Adjust the different structural parameters of the model and select the parameters with the best drag reduction rate for the modeling design. The numerical simulation results show that the optimal drag reduction rate of the two-stage drag reduction structure is greater than 21%. In the flow channel test experiment, the drag reduction rate is slightly lower than the simulation results. Numerical simulation and experimental data show that the underwater drag reduction function can be realized by simulating the microstructure of loach skin. Finally, analyze the velocity gradient, vortices, etc., and search for the drag reduction mechanism. The simulation design of the microstructure of the loach skin can increase the thickness of the boundary layer, promote the vortex structure near the wall surface, change the flow mode of the solid-liquid interface, and reduce the wall resistance. At the same time, the drag reduction model provides key technical support for the practical application of reducing surface resistance, such as in underwater vehicles.

Bifunctional Hole-Transport Materials with Modification and Passivation Effect for High-Performance Inverted Perovskite Solar Cells.

Hole-transport materials (HTMs) play an important role in perovskite solar cells (PSCs) to enhance the power conversion efficiency (PCE). The innovation of HTMs can increase the hole extraction ability and reduce interfacial recombination. Three organic small molecule HTMs with 4H-cyclopenta[2,1-b:3,4-b']dithiophene (CPDT) as the central unit was designed and synthesized, namely, CPDTE-MTP (with the 2-ethylhexyl substituent and diphenylamine derivative end-group), CPDT-MTP (with the hexyl substituent and diphenylamine derivative end-group), and CPDT-PMTP (with the hexyl substituent and triphenylamine derivative end-group), which can form bifunctional and robust hole transport layer (HTL) on ITO and is tolerable to subsequent solvent and thermal processing. The X-ray photoelectron spectroscopy (XPS) results proved that CPDT-based HTMs can both interact with ITO through the nitrogen element in them and the tin element in ITO and passivate the upper perovskite layer. It is worth noting that the champion efficiency of MAPbI3 PSCs based on CPDT-PMTP achieved 20.77%, with an open circuit voltage (VOC) of 1.10 V, a short-circuit current (JSC) of 23.39 mA cm-2, and a fill factor (FF) of 80.83%, as three new materials were introduced into p-i-n PSCs as dopant-free HTMs.

High-Efficiency Sb2Se3 Solar Cells Modified by Potassium Hydroxide.

Antimony selenide (Sb2Se3) has attracted considerable attention for its simple composition, nontoxic nature, and abundance. However, the efficiency of Sb2Se3 solar cells is limited by the low carrier concentration and high recombination rate at the interface between Sb2Se3 and the Au layer. For this paper, the KOH solution used as the etchant was used to increase the efficiency of Sb2Se3 solar cells. The KOH solution not only reacts with (etching the surface) but also diffuses inside the Sb2Se3 film. This study unexpectedly demonstrates that KOH also increases the doping density and improves the back contact (the thin Sb2O3 layer exists with the etching of the KOH solution) of Sb2Se3 solar cells. Lastly, the best power conversion efficiency of 7.16% is demonstrated with a high open-circuit voltage of 0.407 V; we believe our work can serve as a guide for further development of high-efficiency Sb2Se3 solar cells.

Fluorinating Dopant-Free Small-Molecule Hole-Transport Material to Enhance the Photovoltaic Property.

For the stability and commercial development of the perovskite solar cells (PVK-SCs), synthesizing high-efficiency dopant-free hole-transport materials (DF-HTMs) and exploring how the DF-HTM structure affects the photovoltaic performance is inevitable. Two small-molecule DF-HTMs based on 2,2'-bithiophene as a central part (denoted by BT-MTP and DFBT-MTP) were designed and synthesized. DFBT-MTP, with two more fluorine atoms substituted on the 2,2'-bithiophene group, exhibited enhanced photovoltaic property as DF-HTMs, including larger backbone planarity, declining highest occupied molecular orbit (HOMO) energy level, increasing hole transportation, more effective passivation, and efficient charge extraction. With fluorinated DFBT-MTP being applied as DF-HTMs in p-i-n PVK-SCs, an efficiency of 20.2% was achieved, showing ∼35% efficiency increase compared with the nonfluorinated BT-MTP-based devices. The leading power conversion efficiency (PCE) indicates that the fluorinated compounds should be a promising direction for exploring high-performance DF-HTMs in the p-i-n PVK-SCs.

Highly Efficient and Stable Perovskite Solar Cells Using an Effective Chelate-Assisted Defect Passivation Strategy.

Perovskite solar cells are sensitive to subtle changes in atmospheric conditions, resulting in problems such as the collapse of the perovskite structure and sharp drops in efficiency. Internal defects are also a big obstacle for high-quality polycrystalline perovskites. At present, it is difficult to control the density of the trapping sites. By using the bidentate chelating agent thenoyltrifluoroacetone (ttfa), the crystallization kinetics, grain sizes, and crystal defect of Cs-, methylammonium-, and formamidinium-based perovskite materials can be to effectively controlled through a nucleation and growth process for the preparation of perovskite crystals. Crystalline-state tuning during the crystallization process to obtain better quality perovskite thin films can be achieved with no additional operation, which is suitable for the needs of modern industrial production and management. The chelating agent can effectively passivate the defects in perovskite films, leading to a low defect density and a long charge carrier lifetime. As a result, the ttfa-passivated perovskite solar cell demonstrated a high power conversion efficiency of 19.70 % with superior stability retention of 64 % of the initial power conversion efficiency after two weeks unencapsulated storage in an adverse atmosphere with approximately 50 % relative humidity.

Interfacial Engineering at the 2D/3D Heterojunction for High-Performance Perovskite Solar Cells.

Perovskite solar cells based on two-dimensional/three-dimensional (2D/3D) hierarchical structure have attracted significant attention in recent years due to their promising photovoltaic performance and stability. However, obtaining a detailed understanding of interfacial mechanism at the 2D/3D heterojunction, for example, the ligand-chemistry-dependent nature of the 2D/3D heterojunction and its influence on charge collection and the final photovoltaic outcome, is not yet fully developed. Here we demonstrate the underlying 3D phase templates growth of quantum wells (QWs) within a 2D capping layer, which is further influenced by the fluorination of spacers and compositional engineering in terms of thickness distribution and orientation. Better QW alignment and faster dynamics of charge transfer at the 2D/3D heterojunction result in higher charge mobility and lower charge recombination loss, largely explaining the significant improvements in charge collection and open-circuit voltage (VOC) in complete solar cells. As a result, 2D/3D solar cells with a power-conversion efficiency of 21.15% were achieved, significantly higher than the 3D counterpart (19.02%). This work provides key missing information on how interfacial engineering influences the desirable electronic properties of the 2D/3D hierarchical films and device performance via ligand chemistry and compositional engineering in the QW layer.

Electrical Properties of Ba0.96Ca0.04Ti0.90Sn0.10O3 Lead-Free Ceramics with the Addition of Nano-CeO2.

Well dispersed CeO2 nanoparticles are prepared by azeotropic co-precipitation method. (Ba0.96Ca0.04)(Ti0.90Sn0.10)O3 lead-free piezoelectric ceramics doped with nano-CeO2 (x =0 mol%, 0.03 mol%, and 0.07 mol%) and micro-CeO2 (x = 0.03 mol%) are prepared at 1430 °C for 2 h by the conventional solid state sintering method. XRD diffraction indicates that all components have typical perovskite structure. Both doping of nano-CeO2 and micro-CeO2 can inhibit grain growth. And the average grain size decreased apparently with the increase of nano-CeO2 amount. All the samples exhibit typical diffuse phase transition behavior. The optimized electrical performances are obtained at x = 0.03 mol% with d33 = 512 pC/N, kp = 41.5%, and Pr = 14.00 µC/cm².

High-Performance Flexible Perovskite Solar Cells with Effective Interfacial Optimization Processed at Low Temperatures.

Exploration of low-temperature solution-processing methodologies for fabricating planar perovskite solar cells (PSCs) is important for industrial mass production and helps simplify the manufacture and design of flexible perovskite solar cells. However, the interface between electron-transport layers (ETLs) and perovskite layers is crucial for the development of highly efficient flexible PSCs. We report a drastically improved solar cell efficiency through surface optimization of TiO2 ETLs by using a simple and inexpensive ionic compound that shows high optical transparency and superior electron mobility. Solution-derived TiO2 nanocrystalline films are employed at low temperatures as ETLs through solution processing. The modification of TiO2 with NH4 Cl can increase the interactions between the surface and organic-inorganic hybrid perovskites; Cl anions lead to a stronger interfacial coupling between TiO2 and perovskite. Ammonium cations tend to combine with perovskite. Due to this strong combined effect of the ionic compound, the efficiency of PSC from low-temperature solution processing reaches 18.71 % on rigid glass/indium tin oxide (ITO) for an improvement of 12.6 % over a control device using bare TiO2 . Furthermore, the power conversion efficiency (PCE) can reach an efficiency of 17.69 % for the ITO/PEN substrates. This work contributes to the evolution of flexible PSCs with simple fabrication and high device performance.

Totally room-temperature solution-processing method for fabricating flexible perovskite solar cells using an Nb2O5-TiO2 electron transport layer.

Flexible perovskite solar cells are new technology-based products developed by the global solar industry and are promising candidates for realizing a flexible and lightweight energy supply system for wearable and portable electronic devices. A critical issue for flexible perovskite solar cells is to achieve high power conversion efficiency (PCE) while using low-temperature solution-based technology for the fabrication of a compact charge collection layer. Herein, we innovatively introduce niobium ethoxide as a precursor additive to TiO2 NCs, which allows realization of an Nb2O5-TiO2 electron transport layer (ETL). The presence of Nb2O5 remarkably enhances electron mobility and electrical conductivity of the ETLs. In addition, uniform perovskite films are prepared by an annealing-free solution-based method. The excellent performance of the cell is attributed to its smooth film surface and high electron mobility, and performance is verified by the effective suppressions of charge recombination and time-resolved photoluminescence. PCEs of 15.25% and 13.60% were obtained for rigid substrates (glass/fluorine-doped tin oxide) and an indium tin oxide/PET (poly(ethylene terephthalate)) flexible substrate by using a totally room-temperature solution-processing method, respectively.

[Role of TRPC6 in pulmonary artery smooth muscle cells proliferation and apoptosis under hypoxia and hypercapnia].

The present study was to investigate the role of TRPC6 in pulmonary artery smooth muscle cells (PASMCs) proliferation and apoptosis under hypoxia and hypercapnia. PASMCs were isolated from chloral hydrate-anesthetized male Sprague-Dawley (SD) rats. Cellular purity was assessed by immunofluorescence staining for smooth muscle α-actin under fluorescence microscopy. Passage 4-6 PASMCs were starved for 24 h in serum-free DMEM and divided into 5 groups randomly: normoxia, hypoxia and hypercapnia, DMSO, TRPC6 inhibitor SKF-96365 and TRPC6 activator OAG groups. The normoxic group was incubated under normoxia (5% CO2, 21% O2, 37 °C) for 24 h, and the others were incubated with corresponding drugs under hypoxic and hypercapnic (6% CO2, 5% O2, 37 °C) atmosphere for 24 h. TRPC6 mRNA was detected by reverse transcription-PCR. TRPC6 protein was detected by Western blotting. The proliferation of PASMCs was performed by CCK-8 kit. Apoptosis of the PASMCs was detected using TUNEL assay. The [Ca2+]i in the PASMCs was measured using Fura 2-AM fluorescence. The results showed that the expressions of TRPC6 mRNA and protein, and [Ca2+]i were upregulated under hypoxic and hypercapnic conditions. Hypoxia and hypercapnia promoted cellular proliferation and inhibited apoptosis in the PASMCs. OAG enhanced the above-mentioned effects of hypoxia and hypercapnia, whereas SKF-96365 reversed these effects. These results suggest that TRPC6 may play a role in PASMCs proliferation and apoptosis under hypoxia and hypercapnia by regulating [Ca2+]i.

[Effects of ischemic postconditioning on pneumocyte apoptosis after lung ischemia/reperfusion injury in rats].

OBJECTIVE: To investigate the effects of ischemic postconditioning (IPostC) on pneumocyte apoptosis after lung ischemia/reperfusion injury in rats. METHODS: Adult male SD rats were randomly divided into 3 groups based upon the intervention (n = 8): control group (C), lung ischemic reperfusion group (LIR), LIR+ IPostC group (IPostC). At the end of the experiment, blood specimens drawn from the arteria carotis were tested for the content of malondialdehyde (MDA), the activity of superoxide dismutase (SOD) and myeloperoxidase (MPO); the pneumocyte apoptosis index (AI) was achieved by tennrminal deoxynucleotidyl transferase mediated dUTP nick end abeling (TUNEL); the expression of Bcl-2, Bax protein in lung tissue was accessed by quantitative immunohistochemistry (MHC) and Bcl-2, Bax mRNA by RT-PCR. RESULTS: IPostC could significantly attenuate the MDA level, MPO activity and improve SOD activity in blood serum which was comparable to I/R and significantly reduced the number of TUNEL-positive cells compared with I/R group, expressed as Al (% total nuclei) from (39.0 +/- 3.46) to (8.0 +/- 0.88) (P < 0.01). The protein and mRNA expression of Bcl-2 and Bax showed that IPO significantly attenuated the ischemia/reperfusion-upregulated expression of Bax protein but improved the expression of Bcl-2 that improved the Bcl-2/Bax ratio (P < 0.01) . CONCLUSION: IPostC may attenuate pneumocyte apoptosis in LIRI by up-regulating expression of Bcl-2/Bax ratio and by inhibiting oxidant generation and neutrophils filtration.

[The relationship between endogenous hydrogen sulfide system and pulmonary hypertension induced by hypoxic hypercapnia].

OBJECTIVE: To investigate the changes of the endogenous hydrogen sulfide(H2S) system in pulmonary hypertension induced by hypoxic hypercapnia (HHPH) in rats and approach the possible mechanisms. METHODS: 20 SD rats were randomly divided into control group (C) and hypoxic hypercapnia group (HH) (n=10). The changes of hemodynamics and the right ventricle/left ventricle + septum (RV/LV + SP) were measured. The ratio of vessel wall area and total area (WA/TA) of arteriae pulmonalis were observed under lightmicroscope. By using TdT-mediated dUTP nick end labeling (TUNEL) and immunocytochemistry techniques, apoptosis index (AI) and expression of Bcl-2, Bax protein in arteriae pulmonalis were tested. Plasma level of H2S and activity of H2S generating enzymes in homogenates of rat lung tissue were evaluated by sensitive modified sulfide electrode method. Cystathionine-gamma-lyase (CSE) mRNA in lung tissues was determined by RT-PCR. RESULTS: The level of mean pulmonary arterial pressure(mPAP), WA/TA and RV/LV + SP were significantly higher in HH group than those in C group (P < 0.05 or P < 0.01). Compared with those in C group, the AI of arteriae pulmonalis in HH group were significantly lower; the expression of Bcl-2 protein increased while that of Bax protein decreased, and the ratio of Bax/Bcl-2 went up obviously (all P < 0.01). Plasma level of H2S, the activity of H2S generating enzymes and CSE mRNA in HH group were significantly lower than those in C group (all P < 0.01). Plasma level of H2S, the activity of H2S generating enzymes, CSE mRNA each was closely positively related to Al while inversely related to mPAP and Bcl-2/Bax (all P < 0.01). CONCLUSION: The endogenous hydrogen sulfide system is closely related to pulmonary hypertension induced by hypoxic hypercapnia. The depression of the H2S/CSE system in HHPH may help increase the ratio of Bcl-2/Bax, inhibit apoptosis of pulmonary artery smooth muscle cells and finally result in the formation of pulmonary hypertension.

[Involvement of metallothionein in the protection of lung ischemic preconditioning].

The aim of the present study was to investigate whether metallothionein was involved in the protection of lung ischemic preconditioning (IP) against lung ischemia-reperfusion (I/R) injury. Adult male Sprague-Dawley rats were randomly divided into 3 groups based upon the intervention (n=8): control group (C), lung I/R group (I/R), lung I/R+IP group (IP). At the end of the experiment, the content of metallothionein was tested in lung tissue. Blood specimens collected from the arteria carotis were tested for the contents of malondialdehyde (MDA), the activities of superoxide dismutase (SOD) and myeloperoxidase (MPO). The pneumocyte apoptosis index (AI) was determined by terminal deoxynucleotidyl transferase mediated dUTP nick end labeling (TUNEL). Ultrastructural changes of lung tissue were observed by using transmission electron microscope. The results showed that in I/R group, the content of metallothionein was decreased (P<0.05), the content of MDA and MPO activity were increased (P<0.01), and SOD activity was decreased (P<0.01), compared with those in control group. IP treatment significantly increased the content of metallothionein (P<0.01), attenuated the MDA level (P<0.05) and MPO activity (P<0.01), and improved SOD activity (P<0.01) in blood serum. The number of TUNEL-positive cells in IP group was significantly reduced compared with that in I/R group (P<0.01). There were abnormal ultrastructural changes in I/R group, which were markedly reversed in IP group. In conclusion, IP may protect lung against I/R injury by inducing the expression of metallothionein.

Role of heme oxygenase-1/carbon monoxide system in pulmonary ischemia-reperfusion injury.

The aim of this study is to investigate the effect of heme oxygenase-1 (HO-1)/carbon monoxide (CO) system in pulmonary ischemia-reperfusion injury (PIRI) in rabbits. The rabbits were randomly assigned to three groups (n=10, in each): control group (C), PIR group (I-R), PIR+Hemin group (H) and PIR+zinc protoporphyrin IX (ZnPP) group (Z). There were changes to several parameters which included plasma carboxyhemoglobin (COHb), wet to dry ratio of lung tissue weight (W/D), the injured alveoli rate (IAR) and the HO-1 enzymatic activity. Immunohistochemistry and in situ hybridization for HO-1 was detected in lung. The electron microscopic observation for lung tissue injury was done after PIRI. The plasma content of COHb increased by reperfusion was strengthened by hemin but weakened by ZnPP. The HO-1 activity in lung tissue was upregulated by PIRI, further enhanced by hemin and abolished by ZnPP. Except for the C group, HO-1 was upregulated in all other groups in the pulmonary endothelial cells, some pulmonary vascular smooth muscle cells, extima of vessels and epithelial cells of airway. The injury parameters were highest in the Z group, the second was in the IR group, then the H group and the C group. HO-1/CO system was activated and may be one of the protective signal pathway during PIRI in rabbits.