Tomographic imaging of carbon dioxide in the exhaust plume of large commercial aero-engines.

We report here the first implementation of chemically specific imaging in the exhaust plume of a gas turbine typical of those used for propulsion in commercial aircraft. The method used is chemical species tomography (CST) and the target species is CO2, absorbing in the near-infrared at 1999.4 nm. A total of 126 beams propagate transverse to the plume axis, along 7 m paths in a coplanar geometry, to probe a central region of diameter ≈1.5m. The CO2 absorption spectrum is measured using tunable diode laser spectroscopy with wavelength modulation, using the second harmonic to first harmonic (2f/1f) ratio method. The engine is operated over the full range of thrust, while data are recorded in a quasi-simultaneous mode at frame rates of 1.25 and 0.3125 Hz. Various data inversion methodologies are considered and presented for image reconstruction. At all thrust levels a persistent ring structure of high CO2 concentration is observed in the central region of the measurement plane, with a raised region in the middle of the plume assumed to be due to the engine's boat tail. With its potential to target various exhaust species, the CST method outlined here offers a new approach to turbine combustion research, turbine engine development, and aviation fuel research and development.

Constrained models for optical absorption tomography.

We consider the inverse problem of concentration imaging in optical absorption tomography with limited data sets. The measurement setup involves simultaneous acquisition of near-infrared wavelength-modulated spectroscopic measurements from a small number of pencil beams equally distributed among six projection angles surrounding the plume. We develop an approach for image reconstruction that involves constraining the value of the image to the conventional concentration bounds and a projection into low-dimensional subspaces to reduce the degrees of freedom in the inverse problem. Effectively, by reparameterizing the forward model, we impose, simultaneously, spatial smoothness and a choice among three types of inequality constraints, namely, positivity, boundedness, and logarithmic boundedness in a simple way that yields an unconstrained optimization problem in a new set of surrogate parameters. Testing this numerical scheme with simulated and experimental phantom data indicates that the combination of affine inequality constraints and subspace projection leads to images that are qualitatively and quantitatively superior to unconstrained regularized reconstructions. This improvement is more profound in targeting concentration profiles of small spatial variation. We present images and convergence graphs from solving these inverse problems using Gauss-Newton's algorithm to demonstrate the performance and convergence of our method.

3D-printed miniature gas cell for photoacoustic spectroscopy of trace gases.

A new methodology for the development of miniature photoacoustic trace gas sensors using 3D printing is presented. A near-infrared distributed feedback (DFB) laser is used together with a polymer-based gas cell, off-the-shelf fiber optic collimators, and a microelectromechanical system (MEMS) microphone to measure acetylene at 1532.83 nm. The resonance behavior of the miniature gas cell is analyzed using a theoretical and experimental approach, with a measured resonance frequency of 15.25 kHz and a Q-factor of 15. A minimum normalized noise equivalent absorption of 4.5×10(-9) W cm(-1) Hz(-1/2) is shown together with a 3σ detection limit of 750 parts per billion (ppb) for signal averaging times of 35 s. The fiber-coupled delivery and miniature cost-effective cell design allows for use in multipoint and remote detection applications.

Suppression of intensity modulation contributions to signals in second harmonic wavelength modulation spectroscopy.

Recovery of the full 2f wavelength modulation spectroscopy (WMS) signal in isolation from the 2f residual amplitude modulation (RAM) due to nonlinear intensity modulation (IM) and distortion due to linear IM is demonstrated. The 2f RAM is eliminated using a fiber delay line, while the linear IM-induced distortion is eliminated by a phasor decomposition approach. This generic and robust two-pronged strategy removes the need to separately measure the 2f RAM in high-modulation-index calibration-free 2f WMS. It is also important for widely tunable 2f WMS using nontelecom diode lasers with highly nonlinear characteristics leading to high-2f RAM levels.

Influence of the wavelength-dependence of fiber couplers on the background signal in wavelength modulation spectroscopy with RAM-nulling.

Recently a technique to optically eliminate the background residual amplitude modulation in 1f wavelength modulation spectroscopy was demonstrated, where perfect elimination throughout the scan range was not achieved due to the wavelength-dependence of couplers and that of the laser intensity modulation. This paper theoretically analyzes the technique and experimentally demonstrates that the elimination can be perfect for one of three possible experimental configurations, making this important for potential applications with some recently-developed laser sources. For the other configurations a non-zero background slope is predicted, experimentally verified, and the anomalous nature of signals is thereby explained. A common signal normalization method is devised that is independent of the signal slope, a fact that is important for industrial deployment of such systems.

Elimination of residual amplitude modulation in tunable diode laser wavelength modulation spectroscopy using an optical fiber delay line.

A new fiber-optic technique to eliminate residual amplitude modulation in tunable diode laser wavelength modulation spectroscopy is presented. The modulated laser output is split to pass in parallel through the gas measurement cell and an optical fiber delay line, with the modulation frequency / delay chosen to introduce a relative phase shift of pi between them. The two signals are balanced using a variable attenuator and recombined through a fiber coupler. In the absence of gas, the direct laser intensity modulation cancels, thereby eliminating the high background. The presence of gas induces a concentration-dependent imbalance at the coupler's output from which the absolute absorption profile is directly recovered with high accuracy using 1f detection.