Aerial drone furnished with miniaturized versatile air sampling systems for selective collection of nitrogen containing compounds in boreal forest.

A wide variety of nitrogen-containing compounds are present in the environment, which contributes to air pollution and new particle formation, for example. These eventually affect human health and the climate. With all this consideration, there is a growing interest in the development of efficient and reliable methods to determine these compounds in the atmosphere. In this study, titanium hydrogen phosphate-modified Mobil Composition of Matter No. 41 was used as sorbent material for in-tube extraction (ITEX) sampling system, to selectively collect nitrogen-containing compounds from natural air samples. The effect of sampling accessories, based on adsorbent coatings (with Tenax-GR as an adsorbent material) and polytetrafluoroethylene filters, was studied to improve the selectivity of the sampling system and to remove particles. Aerial drone with miniaturized air sampling system was employed for the reliable collection of nitrogen-containing compounds in both gas phase and aerosol particles. A total of 170 air samples were collected in July 2020 at the SMEAR II station, Finland to evaluate nitrogen-containing compounds diurnal patterns and vertical profiles (0.25, 5, 50, and 150 m). More than twenty nitrogen-containing compounds, such as aliphatic amines, imines, imidazoles, and pyridines, were identified, quantified or semi-quantified. The average concentrations of detected aliphatic amines at the altitude of 50 m were up to 40.4 ng m-3 (dimethylamine) in gas phase and 128 ng m-3 (ethylamine) in aerosol particles. Among nitrogen-containing compounds detected, pyridine gave the highest average concentration of 746 ng m-3 in gas phase and 644 ng m-3 in particle phase.

Quantitative analysis and spatial and temporal distribution of volatile organic compounds in atmospheric air by utilizing drone with miniaturized samplers.

Our second generation air sampling drone system, allowing the simultaneous use of four solid phase microextraction (SPME) Arrow and four in-tube extraction (ITEX) units, was employed for collection of atmospheric air samples at different spatial and temporal dimensions. SPME Arrow coated with two types of materials and ITEX with 10% polyacrylonitrile as sorbent were used to give a more comprehensive chemical characterization of the collected air samples. Before field sampling, miniaturized samplers went through quality control and assurance in terms of reproducibility (RSD ≤14.1%, N = 4), equilibrium time (≥10 min), breakthrough volume (1.8 L) and storage time (up to 48 h). 128 air samples were collected under optimal sampling conditions from July to September 2019 at the SMEAR II station and Qvidja farm, Finland. 347 VOCs were identified in the air samples either on-site or in the laboratory by thermal desorption gas chromatography - mass spectrometry, and they were quantified/semiquantified using Partial Least Squares Regression models. Individual models were developed for the different coatings and packing materials using gas phase standards obtained by an automatic permeation system. Average gas phase VOC concentrations ranged from 0.1 (toluene, the SMEAR II station) to 680 ng L-1 (acetone, Qvidja farm). Average VOC concentrations in aerosols ranged from 0.1 (1,4-cyclohexadiene, the SMEAR II station) to 2287 ng L-1 (megastigma-4,6,8-triene, Qvidja farm). Clear differences in results were seen for samples collected at the SMEAR II station and Qvidja farm, between VOC compositions in gas phase and aerosols, and between the sampling site and height.

Broadband Laser-Based Infrared Detector for Gas Chromatography.

Cantilever-enhanced photoacoustic spectroscopy coupled with gas chromatography is used to quantitatively analyze a mixture of alcohols in a quasi-online manner. A full identification and quantification of all analytes are achieved based on their spectral fingerprints using a widely tunable continuous-wave laser as a light source. This can be done even in the case of interfering column/septum bleed or simultaneously eluted peaks. The combination of photoacoustic spectroscopy and gas chromatography offers a viable solution for compact and portable instruments in applications that require straightforward analyses with no consumables.

Automated On-Line Isolation and Fractionation System for Nanosized Biomacromolecules from Human Plasma.

An automated on-line isolation and fractionation system including controlling software was developed for selected nanosized biomacromolecules from human plasma by on-line coupled immunoaffinity chromatography-asymmetric flow field-flow fractionation (IAC-AsFlFFF). The on-line system was versatile, only different monoclonal antibodies, anti-apolipoprotein B-100, anti-CD9, or anti-CD61, were immobilized on monolithic disk columns for isolation of lipoproteins and extracellular vesicles (EVs). The platelet-derived CD61-positive EVs and CD9-positive EVs, isolated by IAC, were further fractionated by AsFlFFF to their size-based subpopulations (e.g., exomeres and exosomes) for further analysis. Field-emission scanning electron microscopy elucidated the morphology of the subpopulations, and 20 free amino acids and glucose in EV subpopulations were identified and quantified in the ng/mL range using hydrophilic interaction liquid chromatography-tandem mass spectrometry (HILIC-MS/MS). The study revealed that there were significant differences between EV origin and size-based subpopulations. The on-line coupled IAC-AsFlFFF system was successfully programmed for reliable execution of 10 sequential isolation and fractionation cycles (37-80 min per cycle) with minimal operator involvement, minimal sample losses, and contamination. The relative standard deviations (RSD) between the cycles for human plasma samples were 0.84-6.6%.

Layered double hydroxide/poly(vinylpyrrolidone) coated solid phase microextraction Arrow for the determination of volatile organic compounds in water.

Today, wide variety of adsorbents have been developed for sample pretreatment to concentrate and separate harmful substances. However, only a few solid phase microextraction Arrow adsorbents are commercially available. In this study, we developed a new solid phase microextraction Arrow coating, in which nanosheets layered double hydroxides and poly(vinylpyrrolidone) were utilized as the extraction phase and poly(vinyl chloride) as the adhesive. This new coating entailed higher extraction capacity for several volatile organic compounds (allyl methyl sulfide, methyl propyl sulfide, 3-pentanone, 2-butanone, and methyl isobutyl ketone) compared to the commercial Carboxen 1000/polydimethylsiloxane coating. Fabrication parameters for the coating were optimized and extraction and desorption conditions were investigated. The validation of the new solid phase microextraction Arrow coating was accomplished using water sample spiked with volatile organic compounds. Under the optimal conditions, the limits of quantification for the five volatile organic compounds by the new solid phase microextraction Arrow coating and developed gas chromatography with mass spectrometry method were in the range of 0.2-4.6 ng/mL. The proposed method was briefly applied for enrichment of volatile organic compounds in sludge.

Fully Automated Online Dynamic In-Tube Extraction for Continuous Sampling of Volatile Organic Compounds in Air.

Comprehensive and time-dependent information (e.g., chemical composition, concentration) of volatile organic compounds (VOCs) in atmospheric, indoor, and breath air is essential to understand the fundamental science of the atmosphere, air quality, and diseases diagnostic. Here, we introduced a fully automated online dynamic in-tube extraction (ITEX)-gas chromatography/mass spectrometry (GC/MS) method for continuous and quantitative monitoring of VOCs in air. In this approach, modified Cycle Composer software and a PAL autosampler controlled and operated the ITEX preconditioning, internal standard (ISTD) addition, air sampling, and ITEX desorption sequentially to enable full automation. Air flow passed through the ITEX with the help of an external pump, instead of plunger up-down strokes, to allow larger sampling volumes, exhaustive extraction, and consequently lower detection limits. Further, in order to evaluate the ITEX system stability and to develop the corresponding quantitative ITEX method, two laboratory-made permeation systems (for standard VOCs and ISTD) were constructed. The stability and suitability of the developed system was validated with a consecutive 19 day atmospheric air campaign under automation. By using an electrospun polyacrylonitrile nanofibers packed ITEX, selective extraction of some VOCs and durability of over 1500 extraction and desorption cycles were achieved. Especially, the latter step is critically important for on-site long-term application at remote regions. This ITEX method provided 2-3 magnitudes lower quantitation limits than the headspace dynamic ITEX method and other needle trap methods. Our results proved the excellence of the fully automated online dynamic ITEX-GC/MS system for tracking VOCs in the atmospheric air.

Aerial drone as a carrier for miniaturized air sampling systems.

The applicability of an aerial drone as a carrier for new passive and active miniaturized air sampling systems, including solid phase microextration Arrow (SPME Arrow) and in-tube extraction (ITEX), was studied in this research. Thermal desorption, gas chromatography and mass spectrometry were used for the determination of volatile organic compounds (VOCs) collected by the sampling systems. The direct comparison of the profiles of VOCs, simultaneously sampled in air by SPME Arrow system including four different coatings, allowed the elucidation of their adsorption selectivity. A more complex experimental design, involving 20 samples (10 flights) and non-supervised pattern recognition techniques, was needed for the clarification of the same sampling parameters in the case of five ITEX sorbent materials. In addition, ITEX sampling accessories, such as particle, water and ozone traps, were evaluated by comparing the results obtained for air samples simultaneously collected by two ITEX systems, packed with the same sorbent and furnished or not with sampling accessories. The effect of the aerial drone horizontal displacement (HD) on the sampling efficiency was clear in the case of SPME Arrow. The number of detected compounds and their relative peak area values (RPA) revealed a clear increase (4 and 43%, respectively) in comparison with samples collected without drone HD. However, just minor differences were observed in the case of ITEX (2 compounds and 9% of the ∑RPA). In addition, the system was able to provide almost simultaneous passive (SPME Arrow) and active (ITEX) samplings at different altitudes (5 and 50 m), being a good tool for low cost vertical profiling studies (∑RPA decreased over 35% for the samples collected at 50 m). Finally, the successful simultaneous air sampling by SPME Arrow and ITEX systems in two difficult access places, such as boreal forest and wetlands, was demonstrated, resulting in 21 and 31 detected compounds in forest and wetlands by SPME Arrow, and 27 and 39 compounds by ITEX.

Integrated atomic layer deposition and chemical vapor reaction for the preparation of metal organic framework coatings for solid-phase microextraction Arrow.

New chemical vapor reaction (CVR) and atomic layer deposition (ALD)-conversion methods were utilized for preparation of metal organic frameworks (MOFs) coatings of solid phase microextraction (SPME) Arrow for the first time. With simple, easy and convenient one-step reaction or conversion, four MOF coatings were made by suspend ALD iron oxide (Fe2O3) film or aluminum oxide (Al2O3) film above terephthalic acid (H2BDC) or trimesic acid (H3BTC) vapor. UIO-66 coating was made by zirconium (Zr)-BDC film in acetic acid vapor. As the first documented instance of all-gas phase synthesis of SPME Arrow coatings, preparation parameters including CVR/conversion time and temperature, acetic acid volume, and metal oxide film/metal-ligand films thickness were investigated. The optimal coatings exhibited crystalline structures, excellent uniformity, satisfactory thickness (2-7.5 µm), and high robustness (>80 times usage). To study the practical usefulness of the coatings for the extraction, several analytes with different chemical properties were tested. The Fe-BDC coating was found to be the most selective and sensitive for the determination of benzene ring contained compounds due to its highly hydrophobic surface and unsaturated metal site. UIO-66 coating was best for small polar, aromatic, and long chain polar compounds owing to its high porosity. The usefulness of new coatings were evaluated for gas chromatography-mass spectrometer (GC-MS) determination of several analytes, present in wastewater samples at three levels of concentration, and satisfactory results were achieved.

Retention in continuous two-dimensional thermal field-flow fractionation: comparison of experimental results with theory.

A theoretical and experimental study of continuous two-dimensional thermal field-flow fractionation (2D-ThFFF) is presented. Separation takes place in radial flow between two closely spaced discs, one of which is heated and the other cooled in order to maintain a temperature gradient across the channel. The cooled disc, which serves as the accumulation wall, is rotated relative to the other to create a shear component to the fluid flow. Under the influence of the thermal gradient and flow components, the sample components spiral outwards along different paths to the outer rim of the channel to be collected. The general principle of operation is described and an approximate theoretical model formulated for predicting the outlet position for the path of each sample component. The influence of the principal operational parameters, such as radial and angular flow rates and thermal gradient, on the deflection angle of the sample trajectory is investigated. Fractionation is demonstrated for polystyrene polymer standards in a binary solvent consisting of cyclohexane and ethylbenzene. Experimental results are compared with theoretical predictions.

Polyethylene glycol-stabilized lipid disks as model membranes in interaction studies based on electrokinetic capillary chromatography and quartz crystal microbalance.

Distearoylphosphatidylcholine (DSPC)/cholesterol/distearoylphosphatidylethanolamine (DSPE)-polyethylene glycol 5000 [PEG(5000)] lipid disks, mimicking biological membranes, were used as pseudostationary phase in partial filling electrokinetic capillary chromatography (EKC) to study interactions between pharmaceuticals and lipid disks. Capillaries were coated either noncovalently with a poly(1-vinylpyrrolidone)-based copolymer or covalently with polyacrylamide to mask the negative charges of the fused-silica capillary wall and to minimize interactions between positively charged pharmaceuticals and capillary wall. Although the noncovalent copolymer coating method was faster, better stability of the covalent polyacrylamide coating at physiological pH 7.4 made it more reliable in partial filling EKC studies. Migration times of pharmaceuticals were proportional to the amount of lipids in the pseudostationary phase, and partition coefficients were successfully determined. Because the capillary coatings almost totally suppressed the electroosmotic flow, it was not practical to use the EKC-based method for partition studies involving large molecules with low mobilities. Hence, the applicability of the biomembrane mimicking lipid disks for interactions studies with large molecules was verified by the quartz crystal microbalance technique. Biotinylated lipid disks were then immobilized on streptavidin-coated sensor chip surface, and interactions with a high-molecular-mass molecule, lysozyme, were studied. Cryo-transmission electron microscopy and asymmetrical flow field-flow fractionation were used to clarify the sizes of lipid disks used.

Thermal aggregation of bovine serum albumin studied by asymmetrical flow field-flow fractionation.

The use of asymmetrical flow field-flow fractionation (AsFlFFF) in the study of heat-induced aggregation of proteins is demonstrated with bovine serum albumin (BSA) as a model analyte. The hydrodynamic diameter (d(h)), the molar mass of heat-induced aggregates, and the radius of gyration (R(g)) were calculated in order to get more detailed understanding of the conformational changes of BSA upon heating. The hydrodynamic diameter of native BSA at ambient temperature was approximately 7 nm. The particle size was relatively stable up to 60 degrees C; above 63 degrees C, however, BSA underwent aggregation (growth of hydrodynamic diameter). The hydrodynamic diameters of the aggregated particles, heated to 80 degrees C, ranged from 15 to 149 nm depending on the BSA concentration, duration of incubation, and the ionic strength of the solvent. Heating of BSA in the presence of sodium dodecyl sulfate (1.7 or 17 mM) did not lead to aggregation. The heat-induced aggregates were characterized in terms of their molar mass and particle size together with their respective distributions with a hyphenated technique consisting of an asymmetrical field-flow fractionation device and a multi-angle light scattering detector and a UV-detector. The carrier solution comprised 8.5 mM phosphate and 150 mM sodium chloride at pH 7.4. The weight-average molar mass (M(w)) of native BSA at ambient temperature is 6.6x10(4) g mol(-1). Incubation of solutions with BSA concentrations of 1.0 and 2.5 mg mL(-1) at 80 degrees C for 1 h resulted in aggregates with M(w) 1.2x10(6) and 1.9x10(6) g mol(-1), respectively. The average radius of gyration and the average hydrodynamic radius of the heat-induced aggregate samples were calculated and compared to the values obtained from the size distributions measured by AsFlFFF. For comparison static light scattering measurements were carried out and the corresponding average molar mass distributions of solutions with BSA concentrations of 1.0 and 2.5 mg mL(-1) at 80 degrees C for 1 h gave aggregates with M(w) 1.7x10(6) and 3.5x10(6) g mol(-1), respectively.

Separation of different ion structures in atmospheric pressure photoionization-ion mobility spectrometry-mass spectrometry (APPI-IMS-MS).

This study demonstrates how positive ion atmospheric pressure photoionization-ion mobility spectrometry-mass spectrometry (APPI-IMS-MS) can be used to produce different ionic forms of an analyte and how these can be separated. When hexane:toluene (9:1) is used as a solvent, 2,6-di-tert-butylpyridine (2,6-DtBPyr) and 2,6-di-tert-4-methylpyridine (2,6-DtB-4-MPyr) efficiently produce radical cations [M](+*) and protonated [M + H](+) molecules, whereas, when the sample solvent is hexane, protonated molecules are mainly formed. Interestingly, radical cations drift slower in the drift tube than the protonated molecules. It was observed that an oxygen adduct ion, [M + O(2)](+*), which was clearly seen in the mass spectra for hexane:toluene (9:1) solutions, shares the same mobility with radical cations, [M](+*). Therefore, the observed mobility order is most likely explained by oxygen adduct formation, i.e., the radical cation forming a heavier adduct. For pyridine and 2-tert-butylpyridine, only protonated molecules could be efficiently formed in the conditions used. For 1- and 2-naphthol it was observed that in hexane the protonated molecule typically had a higher intensity than the radical cation, whereas in hexane:toluene (9:1) the radical cation [M](+*) typically had a higher intensity than the protonated molecule [M + H](+). Interestingly, the latter drifts slower than the radical cation [M](+*), which is the opposite of the drift pattern seen for 2,6-DtBPyr and 2,6-DtB-4-MPyr.

Data analysis programs for comprehensive two-dimensional chromatography.

User-friendly and easy-to-use laboratory-written programs for visualisation and interpretation of comprehensive two-dimensional chromatographic data were developed. The programs that are not tied to any particular commercial instrument, and data obtained either by comprehensive two-dimensional liquid (LC x LC) or gas (GC x GC) chromatography can be analysed. Operations of the programs allow visualisation of 2D and 3D plots, comparison of two 2D plots at a time, as well as determination of retention times and peak heights and volumes.

Modified semi-rotating cryogenic modulator for comprehensive two-dimensional gas chromatography.

A previously constructed semi-rotating cryogenic modulator was modified for comprehensive two-dimensional gas chromatography (GCxGC). The retention time repeatability was improved by replacing the modulator control program unit with a new system. Peak widths obtained with the modified modulator were comparable with those obtained with the previous modulator and other modulator types. The modulator was easy to construct and it can be installed in any commercial GC system. The constructed GCxGC-FID system and data obtained by gas chromatography-mass spectrometry (GC-MS) were used for identification of unknowns in forest aerosol samples.

Electromigration of a heteroconjugated imidazole-acetate complex in ACN.

ACN is an extremely poor hydrogen bond donor and therefore the anions dissolved in it are solvated mainly by other hydrogen bond donors (e.g. uncharged acids) possibly present in the solution. Under properly selected experimental conditions stabilization via hydrogen bonding can be used for separation in CE as has been demonstrated for uncharged acids by several authors. Electromigration based on heteroconjugation can be of importance, e.g. when aqueous separation medium cannot be used due to stability reasons. It also allows CE to be used as a tool for solution chemistry measurements, if the required physicochemical properties of the studied system are known or they can be predicted with sufficient accuracy by existing theories. In the present work we showed that also an uncharged base can stabilize an anion via hydrogen bonding in ACN. In the setup imidazole was chosen as a model base and acetate ion as complexing anion in equimolar acetic acid-acetate buffer. The resulted hydrogen-bonded imidazole-acetate complex (i.e. heteroconjugate) possesses a charge and can thus migrate in CE. It was shown that the studied complexation in ACN is sensitive to competition by other hydrogen bond donors such as water and methanol. On the other hand, acetone, which is a poor hydrogen bond donor, did not have much effect on the complexation. To take the effect of ionic strength on mobility into account, mobilities of the imidazole-acetate complex measured at various ionic strengths were corrected to zero ionic strength by the aid of conductivity equation. A fit of the 1:1 binding isotherm to the ionic strength corrected mobility versus acetate concentration data led to rather good correlation. However, x-reciprocal linear transformation of the binding isotherm showed nonlinearity, which could be partly explained by homoconjugation of acetic acid and acetate ion. Since the homoconjugation constant for acetic acid under present experimental conditions was not available, theoretical simulations were used to demonstrate the effects of homoconjugation. The possibility of multiple complexation of imidazole was discussed as well.

Comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry in the identification of organic compounds in atmospheric aerosols from coniferous forest.

Comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry (GC x GC-TOF-MS) was applied in the identification of organic compounds in atmospheric aerosols from coniferous forest. The samples were collected at Hyytiälä, Finland, as part of the QUEST campaign, in Spring 2003. Manual and automated search procedures were compared in the identification. An automated procedure is preferable when a large number of data files need to be processed; but manual search was more accurate with the present samples, where the number of compounds was large and most of the compounds of interest were present at trace level. Altogether, about 50 compounds were identified on the basis of mass spectra and linear retention indices. The identified compounds included oxidised monoterpenes, acyclic alkanes, alkenes, ketones and aldehydes, as well as a few alcohols, acids, and aromatic compounds.

Miniaturization of asymmetrical flow field-flow fractionation and application to studies on lipoprotein aggregation and fusion.

Asymmetrical flow field-flow fractionation (AsFlFFF), a technique that provides direct measurement of particle size and diffusion coefficient, is converted into miniaturized scale. In comparison with conventional AsFlFFF, the separation of proteins in miniaturized AsFlFFF is achieved within shorter time periods, with smaller sample amounts, and with lower mobile phase consumption. Minimization of the overloading and optimization of the separation efficiency are prerequisites to good results. Miniaturized AsFlFFF is applied to the measurement of particle sizes of high-density lipoprotein (HDL), low-density lipoprotein (LDL), and very low-density lipoprotein (VLDL). The average hydrodynamic diameters at pH 7.4 in 8.5mM phosphate buffer containing 1mM EDTA and 150 mM NaCl are 8.6+/-0.5, 11.2+/-0.2, 22.1+/-0.7, and 48.9+/-7.5 nm for subgroups HDL3, HDL2, LDL, and VLDL, respectively. In addition, the effect of different factors on the aggregation and fusion of LDL particles is studied. LDL particle sizes are unaffected by the addition of up to 300 mM NaCl and by an increase of the carrier solution pH from 3.2 to 7.4, but treatment of LDL with alpha-chymotrypsin, sphingomyelinase, or copper sulfate leads to the formation of aggregated and fused LDL particles.

Comprehensive two-dimensional liquid chromatography-time-of-flight mass spectrometry in the analysis of acidic compounds in atmospheric aerosols.

A novel method utilising comprehensive two-dimensional liquid chromatography interfaced to electrospray ionisation time-of-flight mass spectrometry was developed for the determination of organic acids in atmospheric aerosols. The system was applied to the analysis of methanolic extracts of filters from a high volume sampler. The enhanced separation power of two-dimensional separation was demonstrated in the analysis of both rural and urban samples. Quantification was performed for compounds for which standards were available. Limit of detection was 2-200 ng/ml. Average reproducibility of retention times in each dimensions was 0.1%, and average reproducibility of peak areas was 8% (10 microg/ml, n=3).

Piperazine-based buffers for liposome coating of capillaries for electrophoresis.

Anionic liposomes can be coated on fused-silica capillaries for electrophoresis in the presence of N-(hydroxyethyl)piperazine-N'-(2-ethanesulfonic acid) (HEPES) as background electrolyte (BGE) solution. In this work, the interaction of various compounds with zwitterionic and anionic phospholipid coatings was studied with HEPES at pH 7.4 as BGE solution. The chromatographic and electrophoretic behavior of three test sample solutions (anionic, cationic, and neutral) was investigated for evaluation of the phospholipid coatings. Our results show that hydrophobic interactions between analytes and the phospholipid coating are important for the migration of charged analytes. In addition, the performances of other piperazine-based buffers, i.e., N-(2-hydroxyethyl)piperazine-N'-(2-hydroxypropanesulfonic acid), piperazine-N,N'-bis(2-ethanesulfonic acid), and piperazine-N,N'-bis(hydroxypropane sulfonic acid), at pH 7.4, as liposome solvent and BGE solution were evaluated and compared with the performance of HEPES at pH 7.4. The anionic liposome solution comprised 80/20 mol% phosphatidylcholine/phosphatidylserine. A simple test solution was selected and the chromatographic and electrophoretic migration behavior of the analytes was evaluated. The results show that, in addition to HEPES, other piperazine-based buffers at pH 7.4 are suitable for coating of fused-silica capillaries with anionic liposomes.

Characterisation of poly(N-isopropylacrylamide) by asymmetrical flow field-flow fractionation, dynamic light scattering, and size exclusion chromatography.

Asymmetrical flow field-flow fractionation (AsFIFFF) was used to determine the hydrodynamic particle sizes, molar masses, and phase transition behaviour of various poly(N-isopropylacrylamide) (PNIPAM) samples synthesised by reversible addition--fragmentation chain transfer (RAFT) and conventional free radical polymerisation processes. The results were compared with corresponding data obtained by dynamic light scattering (DLS) and size exclusion chromatography (SEC). Agreement between the three methods was good except at higher molar masses, where the molar mass averages obtained by SEC were much lower than those obtained by AsFIFFF and light scattering. The aggregation of the polymers, which are thermally sensitive, was studied by DLS and AsFIFFF at various temperatures. In deionised water there was an abrupt change in the particle size due to phase separation at approximately equal to 32-35 degrees C. The critical temperatures determined by AsFIFFF were 3-5 degrees C higher than those obtained by DLS.