Validation of the Finite Element Model versus Biomechanical Assessments of Dental Implants and Total Knee Replacements.

Computer modeling and simulation (CM&S) technology is widely used in the medical device industry due to its advantages such as reducing testing time and costs. However, the developer's parameter settings during the modeling and simulation process can have a significant impact on the results. This study developed a test model for the rotational shear strength of dental implants and the constraint force of total knee replacements based on CM&S technology and proposes ideal parameters to ensure reliability. For dental implants, the load area and sliding contact conditions were considered, and for total knee replacements, the friction coefficient, medial-lateral displacement, valgus-varus rotation, and elastic modulus were considered. By comparing the simulation results and mechanical tests, boundary conditions with an error rate of less than 1.5% were selected. When a jig (gripper and collector) was applied with the same boundary conditions, an error rate of 48~22% occurred; otherwise, it was confirmed that the error rate was within 10~0.2%. The FE model was verified with an error of 2.49 to 3% compared to the mechanical test. The friction coefficient variable had the greatest influence on the results, accounting for 10 to 13%, and it was confirmed that valgus-varus rotation had a greater influence on the results than medial-lateral displacement. Relatively, the elastic modulus of the insert had the least effect on the results. These research results are expected to make CM&S techniques useful as a medical device digital development tool (M3DT) in the development of total knee replacements and dental implants.

Safe Optimal Tear Drop View for Spinopelvic Fixation Using a Three-Dimensional Reconstruction Model of the Pelvis.

Background: Spinopelvic fixation (SPF) has been a challenge for surgeons despite the advancements in instruments and surgical techniques. C-arm fluoroscopy-guided SPF is a widely used safe technique that utilizes the tear drop view. The tear drop view is an image of the corridor from the posterior superior iliac spine to the anterior inferior iliac spine (AIIS) of the pelvis. This study aimed to define the safe optimal tear drop view using three-dimensional reconstruction of computed tomography images. Methods: Three-dimensional reconstructions of the pelvises of 20 individuals were carried out. By rotating the reconstructed model, we simulated SPF with a cylinder representing imaginary screw. The safe optimal tear drop view was defined as the one embracing a corridor with the largest diameter with the inferior tear drop line not below the acetabular line and the lateral tear drop line medial to the AIIS. The distance between the lateral border of the tear drop and AIIS was defined as tear drop index (TDI) to estimate the degree of rotation on the plane image. Tear drop ratio (TDR), the ratio of the distance between the tear drop center and the AIIS to TDI, was also devised for more intuitive application of our simulation in a real operation. Results: All the maximum diameters and lengths were greater than 9 mm and 80 mm, respectively, which are the values of generally used screws for SPF at a TDI of 5 mm and 10 mm in both sexes. The TDRs were 3.40 ± 0.41 and 3.35 ± 0.26 in men and women, respectively, at a TDI of 5 mm. The TDRs were 2.26 ± 0.17 and 2.14 ± 0.12 in men and women, respectively, at a TDI of 10 mm. Conclusions: The safe optimal tear drop view can be obtained with a TDR of 2.5 to 3 by rounding off the measured values for intuitive application in the actual surgical field.

Mechanical alterations in the avascular region of the meniscus following partial meniscectomy: A cadaveric porcine longitudinal meniscal tear model.

BACKGROUND: Although partial meniscectomy is a common treatment for the tears in the avascular region of the meniscus, mechanical alterations following meniscectomy are known to initiate mechanically-induced osteoarthritis. We aimed to measure the articular cartilage contact pressure distributions in the knees with surgically repaired and partially resected menisci in the avascular region. METHODS: A pneumatic loading device was developed to apply a 1000 N compressive load on the cadaveric porcine knee samples at the flexion angles of 20, 35, 50, and 65°. We simulated longitudinal meniscal tears in the avascular inner 1/3 portion and the well-vascularized middle 1/3 portion of the meniscus. Articular cartilage contact pressures for the knees with intact, torn, repaired, and resected menisci were compared. FINDINGS: For the tears in well-vascularized regions, meniscal repairs restored articular cartilage contact pressures to the levels in intact joints. However, partial meniscectomy significantly increases the maximum contact pressures and the average contact pressures in highly compressed areas. However, partial meniscectomy in the avascular region did not alter the maximum articular cartilage contact pressures and the average contact pressures in highly compressed areas. Stabilities in knee samples were not significantly altered following partial meniscectomy in both inner and middle regions. INTERPRETATION: Although repair surgeries are beneficial for the tears in well-vascularized areas because the articular cartilage contact mechanics are reconstructed, partial meniscectomy may be a viable alternative treatment for the tears in avascular regions without introducing significant mechanical alterations.

Distribution of the Force in the Knee Joint during Daily Activities after Open Wedge High Tibial Osteotomy: A Rationale for the Proper Postoperative Management.

The present study was conducted to evaluate the force distribution in knee joint during daily activities after open-wedge high tibial osteotomy (OWHTO). A three-dimensional proximal tibial finite element model (FEM) was created using Mimics software to evaluate computed tomography (CT) scans of the tibia after OWHTO. The anterior and posterior gaps were 7.0 and 12.1 mm, respectively, and the target opening angle was 12 degrees. The loading ratio of the medial and lateral tibial plateaus was 6:4. To evaluate force distribution in the knee joint during activities of daily living (ADLs) after OWHTO, peak von Mises stresses (PVMSs) were analyzed at the plate and posterolateral edge region of osteotomized tibia. ADLs associated with greater knee flexion (sitting 90 degrees, standing 90 degrees, bending 90 degrees, stepping up stairs 60 degrees, and stepping downstairs 30 and 60 degrees) yielded PVMSs ranging from 195.2 to 221.5 MPa at the posterolateral edge region. In particular, stepping downstairs with knee flexion to 60 degrees produced the highest PVMS (221.5 MPa), greater than the yield strength (100-200 MPa). The highest plate PVMS was greater than 300 MPa during ADLs associated with flexion angles of approximately 90 degrees. However, these values did not exceed the yield stress (760.0 MPa). Conclusively, higher force was generated during higher flexion associated with weight-bearing and stepping downstairs produced a high force (even at lower flexion) on the posterolateral area of the tibial plateau. Therefore, a caution should be exercised when engaging in knee flexion of approximately 90 degrees and stepping downstairs in the early postoperative period when patients follow a weight-bearing rehabilitation protocol. However, this study is based on modeling; further translational studies are needed prior to clinical application.

Biomechanical Characteristics of Three Baseplate Rotational Arrangement Techniques in Total Knee Arthroplasty.

INTRODUCTION: Several ongoing studies aim to improve the survival rate following total knee arthroplasty (TKA), which is an effective orthopedic surgical approach for patients with severely painful knee joint diseases. Among the studied strategies, baseplate rotational arrangement techniques for TKA components have been suggested but have been the subject of only simple reliability evaluations. Therefore, this study sought to evaluate comparatively three different baseplate rotational arrangement techniques that are commonly used in a clinical context. MATERIALS AND METHODS: Three-dimensional (3D) finite element (FE) models of the proximal tibia with TKA were developed and analyzed considering three baseplate rotational arrangement techniques (anterior cortex line, tibial tuberosity one-third line, and tibial tuberosity end line) for six activities of daily life (ADLs) among patients undergoing TKA. Mechanical tests based on the ASTM F1800 standard to validate the FE models were then performed using a universal testing machine. To evaluate differences in biomechanical characteristics according to baseplate rotational arrangement technique, the strain and peak von Mises stresses (PVMSs) were assessed. RESULTS: The accuracy of the FE models used in this study was high (94.7 ± 5.6%). For the tibial tuberosity one-third line rotational arrangement technique, strains ≤ 50 µstrain (the critical bone damage strain, which may affect bone remodeling) accounted for approximately 2.2%-11.3% and PVMSs within the bone cement ranged from 19.4 to 29.2 MPa, in ADLs with high loading conditions. For the tibial tuberosity end line rotational arrangement, strains ≤ 50 µstrain accounted for approximately 2.3%-13.3% and PVMSs within the bone cement ranged from 13.5 to 26.7 MPa. For anterior cortex line rotational arrangement techniques, strains ≤50 µstrain accounted for approximately 10.6%-16.6% and PVMSs within the bone cement ranged from 11.6 to 21.7 MPa. CONCLUSION: The results show that the most recently developed frontal cortex line rotational alignment technique is the same or better than the other two rotational alignment techniques in terms of biomechanics. This finding can be, however, dependent on the contact characteristics between the baseplate and the proximal tibia. That is, it is indicated that the optimum baseplate rotational arrangement technique in terms of reducing the incidence of TKA mechanical failure can be achieved by adjusting the characteristics of contact between the baseplate and the proximal tibia.