Assessment of Adaptability and Linear Dimensional Changes of Two Heat Cure Denture Base Resin with Different Cooling Techniques: An In Vitro Study.

AIM: The current study was designed to assess the linear dimensional changes and adaptability of two heat-cured denture base resins using various cooling methods. MATERIALS AND METHODS: To prepare a total of 90 acrylic resin samples (45 acrylic resin samples for each material), four rectangular stainless-steel plates measuring 25 × 25 × 10 mm were fabricated. For both groups, the material was put into the mold at the dough stage. Group I - SR Triplex Hot Heat Cure acrylic; group II - DPI Heat Cure acrylic. Both groups used the same curing procedure. One of the following three techniques was used to cool the material (15 samples from each material) once the curing cycle was finished: (A) water bath, (b) quenching, and (C) air. A traveling microscope was used to measure the distance between the markings on the acrylic samples. The data was recorded and statistically analyzed. RESULTS: In SR Triplex Hot heat cure acrylic material, the maximum linear dimensional changes were found in the quenching technique (0.242 ± 0.05), followed by the air technique (0.168 ± 0.11) and the least was found in the water bath technique (0.146 ± 0.01). In DPI Heat Cure acrylic material, the maximum linear dimensional changes were found in the quenching technique (0.284 ± 0.09), followed by the air technique (0.172 ± 0.18) and the least was found in the water bath technique (0.158 ± 0.10). There was a statistically significant difference found between these three cooling techniques. On comparison of adaptability, the water bath technique, the marginal gap SR Triplex Hot was 0.012 ± 0.02 and DPI Heat Cure was 0.013 ± 0.02. In the quenching technique, the marginal gap SR Triplex Hot was 0.019 ± 0.04 and DPI Heat Cure was 0.016 ± 0.04. In the air technique, the marginal gap SR Triplex Hot was 0.017 ± 0.01 and DPI Heat Cure was 0.019 ± 0.01. CONCLUSION: The present study concluded that among the different cooling methods, the water bath technique had the least linear dimensional change, followed by the air and quenching techniques. When comparing the materials, DPI Heat Cure acrylic resin showed a greater linear dimensional change than SR Triplex Hot heat cure acrylic resin. CLINICAL SIGNIFICANCE: During polymerization, heat-cured acrylic resins experience dimensional changes. Shrinkage and expansion are dimensional changes that occur in heat-cured acrylic resins and have an impact on the occlusal relationship and denture fit. However, the denture base's material qualities and the different temperature variations it experiences during production may have an impact on this. How to cite this article: Kannaiyan K, Rathod A, Bhushan P, et al. Assessment of Adaptability and Linear Dimensional Changes of Two Heat Cure Denture Base Resin with Different Cooling Techniques: An In Vitro Study. J Contemp Dent Pract 2024;25(3):241-244.

Effect of Different Disinfecting Agents on Surface Roughness and Color Stability of Heat-cure Acrylic Denture Material: An In Vitro Study.

AIM: The current study aimed to determine the impact of three different disinfectants on the surface roughness and color stability of heat-cure acrylic denture material. MATERIALS AND METHODS: Using a stainless-steel mold, disc-shaped wax patterns with dimensions of 10 mm in diameter and 2 mm thick (in accordance with ADA Specification No. 12) were created and prepared for a total of 75 acrylic samples. Dimensions of all 75 acrylic samples were checked with a digital Vernier caliper. About 25 samples of denture base material were immersed in three different chemical disinfectants: Group I: immersed in chlorhexidine gluconate solution, group II: immersed in sodium hypochlorite solution, and group III: immersed in glutaraldehyde solution. All samples were scrubbed daily for 1 minute with the appropriate disinfectant and submerged for 10 minutes in the same disinfectant. Between disinfection cycles, samples were kept in distilled water at 37°C. Color stability was measured using a reflection spectrophotometer. Surface roughness values were measured by a profilometer at baseline following 15 days and 30 days. RESULTS: After 15 days, the color stability was better in chlorhexidine gluconate solution group (4.88 ± 0.24) than sodium hypochlorite solution (4.74 ± 0.18) and glutaraldehyde solution group (4.46 ± 0.16). The mean surface roughness was less in glutaraldehyde solution group (2.10 ± 0.19), followed by chlorhexidine gluconate solution group (2.48 ± 0.09) and sodium hypochlorite solution group (2.64 ± 0.03). After 30 days, the color stability was significantly better in chlorhexidine gluconate solution group (4.40 ± 0.02), followed by sodium hypochlorite solution (4.06 ± 0.16) and glutaraldehyde solution group (3.87 ± 0.17). The mean surface roughness was significantly lesser in glutaraldehyde solution group (2.41 ± 0.14), followed by chlorhexidine gluconate solution group (2.94 ± 0.08) and sodium hypochlorite solution group (3.02 ± 0.13). CONCLUSION: In conclusion, the color stability was significantly better in chlorhexidine gluconate solution group than sodium hypochlorite solution and glutaraldehyde solution group. But the surface roughness was significantly lesser in the glutaraldehyde solution group, followed by the chlorhexidine gluconate and sodium hypochlorite solution group. CLINICAL SIGNIFICANCE: The maintenance of the prosthesis requires the use of a denture disinfectant; therefore, it is crucial to select one that is effective but would not have a negative impact on the denture base resin's inherent characteristics over time. How to cite this article: Kannaiyan K, Rakshit P, Bhat MPS, et al. Effect of Different Disinfecting Agents on Surface Roughness and Color Stability of Heat-cure Acrylic Denture Material: An In Vitro Study. J Contemp Dent Pract 2023;24(11):891-894.

Association of Radiographic Signs in Determining the Proximity of Mandibular Third Molar Roots to the Mandibular Canal and Postoperative Occurrence of Neurosensory Disorders: A Cohort Study.

BACKGROUND: The routine oral and maxillofacial procedure involving the surgical removal of impacted mandibular third molars comes with inherent risks to nearby anatomical structures. Proximity of mandibular third molar roots to the inferior alveolar nerve (IAN) poses a significant risk for injury, prompting the need for reliable assessment methods. Radiographic indicators, particularly those observed on intraoral periapical radiographs (IOPARs), offer a dependable means to evaluate proximity. OBJECTIVES: This study seeks to examine the closeness between the mandibular canal and the roots of mandibular third molars using IOPARs and to assess the incidence of postoperative neurosensory disorders. METHODS: A cohort of 100 subjects aged 18 to 25, presenting for partially erupted/ impacted mandibular third molar removal, underwent IOPAR examinations. Data analysis employed IBM SPSS Statistics for Windows, Version 12 (Released 2004; IBM Corp., Armonk, New York, United States), calculating frequencies, percentages, means, standard deviations, and ranges. Radiographic signs of proximity were evaluated, and a standardized surgical procedure was performed under local anesthesia. Postoperative neurosensory disorders were assessed using various methods. RESULTS: Of the evaluated subjects, darkening of the root (52%) was the most prevalent radiographic sign, followed by interruption of the white line of the canal (20%). The prevalence of radiographic signs varied, with none of the patients experiencing narrowing of the root. Postsurgical paraesthesia assessment revealed no nerve sensitivity alterations in any patient. CONCLUSION: Preoperative radiographic examination is imperative for determining the relationship between mandibular third molar roots and the inferior alveolar canal, aiding in preventing IAN damage during extraction. Contrary to radiographic signs, there was no observed association between impacted mandibular third molar radiographic signs and the occurrence of postoperative neurosensory disorders.

Oral Health Status and Treatment Needs of Psychiatric Outpatients Aged 18-64 Years in District Civil Hospital, Raichur, Karnataka: A Cross-Sectional Study.

BACKGROUND: Psychiatric patients or mentally ill patients conform a substantial section of the community deserving special attention. This study aimed to assess the oral health status and treatment needs of psychiatric patients attending District Civil Hospital, Raichur, Karnataka. MATERIALS AND METHODS: The study group comprised 150 outpatients aged 18-64 years, attending the Department of Psychiatry, District Civil Hospital, Raichur. A specific questionnaire was drawn up and was used to record the demographic and medical data and oral hygiene practices. Type III clinical examination was carried out. The WHO Assessment Form 1997 was used to assess the oral health status of the study population. RESULTS: Of the 150 patients examined, 90 (60%) were male and 60 (40%) were female. The mean age of the patients was 33.79 ± 10.57 years. The majority (52%) were diagnosed with epilepsy and 18% had anxiety disorder. The prevalence of caries was 87.3%. Periodontal status, according to the Community Periodontal Index scores, was as follows: 54% of the patients had shallow pocket (4 mm-5 mm) and 32% of the patients had 6-mm or more deep pocket. CONCLUSION: This study highlights a substantial need for prevention and treatment of oral health needs among psychiatric patients, and to increase awareness toward oral health.

Esthetic and Palliative Management of Congenitally Missing Anterior Teeth using All Ceramic Fixed Prosthesis: A Clinical Case Report.

Congenitally missing anterior teeth alters the patient's physiognomy and diction in a big way. Maxillary incisor agenesis, prominently the lateral incisor is the most common congenitally missing permanent tooth, in the anterior maxillary region, which is the esthetic zone, representing approximately 20% of all dental anomalies. Treatment planning is inclusive of; smile design, preparation, perception of the patients, and their expectations in relation to esthetics, interdisciplinary alliance that meets the functional, health, and esthetic needs. A critical factor for the overall success is that of choosing a suitable restorative recourse. The case report describes the esthetic rehabilitation for congenitally missing maxillary lateral incisor and early traumatic loss of central incisor using an all ceramic-fixed prosthesis.

Comparison of Flexural Strength of Kevlar, Glass, and Nylon Fibers Reinforced Denture Base Resins With Heat Polymerized Denture Base Resins.

INTRODUCTION: Polymethyl methacrylate (PMMA) has been widely accepted and used in dentistry owing to its working characteristics, aesthetics and stability in the oral environment, ease in manipulation, and inexpensive processing methods and equipment. AIM AND OBJECTIVES: The aim of this study was to evaluate the flexural strength of a high-impact PMMA denture base resin material and flexural strength of a commonly available heat cure PMMA denture base material with Kevlar, glass, and nylon fibers. MATERIALS AND METHODS: The test samples were studied under two groups. The Group I (control group) comprised pre-reinforced PMMA (Lucitone 199; Dentsply Sirona Prosthetics, York, Pennsylvania, USA) consisting of 12 samples and second group comprised regular PMMA (DPI, Mumbai, India) reinforced with different fibers. The second test group was further divided into three subgroups as Group 2, Group 3, and Group 4 comprising 12 samples each designated by the letters a-l. All the samples were marked on both ends. A total of 48 samples were tested. Results were analyzed and any P value ≤0.05 was considered as statistically significant (t test). RESULTS: All the 48 specimens were subjected to a 3-point bending test on a universal testing machine (MultiTest 10-i, Sterling, VA, USA) at a cross-head rate of 2 mm/min. A load was applied on each specimen by a centrally located rod until fracture occurred; span length taken was 50 mm. Flexural strength was then calculated. CONCLUSION: Reinforcement of conventional denture base resin with nylon and glass fibers showed statistical significance in the flexural strength values when compared to unreinforced high impact of denture base resin.

Occurrence of micronuclei in exfoliated buccal mucosal cells in mobile phone users: A case-control study.

INTRODUCTION: The use of mobile phones has increased enormously all over the world especially among young people. This technology is based upon electromagnetic radiation in the microwave frequency range [radiofrequency (RF) waves and microwaves]. The radiation frequency and modulation standards vary in the range of 300-2100 MHz, depending on the region in the world. AIM AND OBJECTIVES: To detect the presence of micronuclei in exfoliated buccal mucosal cells of mobile phone users as well as to carry out a quantitative analysis of micronuclei in exfoliated buccal mucosal cells of mobile phone users. MATERIAL AND METHODS: A cross-sectional study was carried out in 100 individuals, out of which 50 were included under the test group and 50 under the control group. Buccal mucosal smears were obtained from each subject. Staining was done using papanicuolau (PAP) stain and the slides were examined for the presence of micronuclei. RESULTS: The mean duration of mobile phone usage in years was 5.32 years for the exposed and 2.42 years for the control. Mean duration of mobile phone usage per day in the test group was 94.8 min and 12.4 min in the control group. The frequency of micronucleated cells (MNC) in test and control groups ranged from 0 to 16 and 0 to 2 respectively. The data obtained were statistically analyzed using Student t-test and significant results were obtained at 0.0001 level. CONCLUSION: Our study concluded that there is an increased frequency of micronuclei in mobile phone users which is related to carcinogenesis.

Assessment of Periodontal Health and Necessity of Dental Treatment in the Institutionalized Elderly Population of East Godavari District, Andhra Pradesh.

AIM: To assess the periodontal health condition and treatment needs among elderly people aged 60-85 years residing as inmates in the eight old age homes in East Godavari district, Andhra Pradesh, India. SETTINGS AND DESIGN: A cross-sectional descriptive study was conducted to verify the oral health condition and treatment needs among elderly people aged 60-85 years. MATERIALS AND METHODS: Modified World Health Organization (WHO) 2013 oral health assessment pro forma for adults was used to assess the oral health status and treatment needs, the clinical assessment of oral mucosa, loss of attachment (LOA) , community periodontal index, dentition status, and treatment need. Prosthetic status and prosthetic needs and related oral health information were obtained from WHO Oral Health Assessment Questionnaire. STATISTICAL ANALYSIS USED: SPSS 23 was used for statistical analysis. Chi-square test was used for age- and gender-wise comparison. P < 0.05 was considered statistically significant. RESULTS: Among the study subjects aged 60-74 years, there were 28.1% males and 25.9% females, and in 75-85 years, 30.6% were males 15.3% were females. In terms of periodontal status (pocket scores), 66.2% of elderly people have pocket scores 6 mm or more and presence of gingival bleeding in 75.9% of study subjects. Almost 24.4% had LOA scores of 12 mm or more. Comparison of LOA scores based on age and gender was statistically significant (P < 0.001). Of the study participants, 50.3% need prompt treatment (including scaling). Almost more than half of the study participants require one or multiunit prosthesis as only 10.93% of elderly population has ≥20 or more natural teeth present. CONCLUSION: The study showed poor periodontal health among institutionalized elderly inmates. Oral mucosal lesions were found to be higher and oral health status was very deprived among the study population.