Evaluation of shear bond strength and translucency of zirconia-reinforced lithium silicate and lithium disilicate: An in vitro study.

Aim: To analyze the effect of various surface treatment protocols on shear bond strength between the ceramic and resin cement (RC) and influence of zirconia on the translucency of LD as compared to zirconia-reinforced lithium silicate (ZLS). Setting and Design: In-Vitro Study. Materials and Methods: Specimens (14 mm × 12 mm × 2 mm) (n = 135) and (14 mm × 12 mm × 1 mm) (n = 45) of ZLS computer-aided design/computer-aided manufacturing glass ceramic block and LD were fabricated, respectively. All the ZLS specimens were crystallized and were tested for the translucency parameter and ceramic-resin shear bond strength. Two different types of surface treatment were used on the ZLS and LD samples. The specimens were treated using the hydrofluoric acid (HF) etching or air abrasion with diamond particles (DPs). The specimens were then bonded using self-adhesive RC to a composite disc of 10 mm and thermocycling was performed. A universal testing machine was used to evaluate ceramic-resin shear bond strength after 24 h. The translucency of the specimens was evaluated using the spectrophotometer by calculating the difference in color between the readings over a black background and a white background. Statistical Analysis Used: Data were statistically analyzed using the independent sample t-test and analysis of variance with Bonferroni's correction and comparison was made between the specimens. Results: Independent sample t-test demonstrated statistically significantly higher translucency for group ZLS (61.44 ± 22) as compared to group LD (20.16 ± 8.39) (P < 0.001). Group ZLS showed statistically significant higher shear bond strength when surface treatment using HF or air abrasion with synthetic DPs was performed as compared to untreated group (3.58 ± 0.45) (P < 0.001). Moreover, air abrasion group (16.79 ± 2.11 megapascal [MPa]) demonstrated statistically significant higher shear bond strength as compared to HF etched group (8.25 ± 0.30 MPa) (P < 0.001). Furthermore, statistically significant higher shear bond strength was noted when air abrasion was done for group ZLS (16.79 ± 2.11 MPa) as compared to group LD (10.82 ± 1.92 MPa) (P < 0.001). However, on surface treatment with HF, a statistically significantly lower shear bond strength was noted for group ZLS (8.25 ± 0.30 MPa) as compared to group LD (11.29 ± 0.58 MPa) (P = 0.001). Conclusion: ZLS demonstrated higher translucency compared to LD restorations. DP abrasion of ZLS is recommended to achieve higher shear bond strength between the ceramic and RC.

Assessment of Antagonist Enamel Wear and Clinical Performance of Full-Contour Monolithic Zirconia Crowns: One-Year Results of a Prospective Study.

PURPOSE: To assess the clinical performance and survival of full-contour monolithic zirconia (MZ) crowns and enamel wear produced over a 1-year period. MATERIALS AND METHODS: 60 patients requiring full-coverage restorations for endodontically treated posterior teeth opposed by healthy unrestored antagonistic teeth were selected. MZ crowns were fabricated. Vinyl polysiloxane impressions of the antagonist teeth were made, and the stone casts were digitized using a 3D laser scanner. Wear of the opposing natural teeth was evaluated at baseline (1 week), 6 months, and 1 year after crown cementation. Superimposition of the follow-up scans on the baseline scans were performed to evaluate wear. Survival and function of the restorations were evaluated by the modified USPHS rating criteria at the same timeframes. RESULTS: Comparison of the baseline and the follow-up wear values was statistically tested using the paired t-test. Statistical significance was noted between the wear values at 6 months (15.5 µm) and at 12 months (16.3 µm) (p < 0.05). The Wilcoxon signed rank sum test was performed to evaluate each parameter of the modified USPHS criteria and to analyze the change in the follow-up scores of the restorations. The survival rate for the crowns was 100%. Results were classified as "excellent" over a 1-year follow up. CONCLUSIONS: MZ crowns showed promising results related to antagonist enamel wear and survival/clinical performance.

Replicating a discolored tooth preparation: A technique for effective laboratory communication.

Fabricating a ceramic restoration for a discolored anterior tooth presents a clinical challenge. The dental technician is often hampered by being unaware of the shade of the discolored tooth preparation, which influences the color of the overlying ceramic restoration. A definitive cast that replicates the shade of the prepared tooth helps the ceramist to fabricate a restoration that masks the discoloration appropriately and still achieves the desired optical properties. This report demonstrates the use of a technique of recording and communicating the shade of a prepared tooth to the dental laboratory technician.

Does Graft Particle Type and Size Affect Ridge Dimensional Changes After Alveolar Ridge Split Procedure?

PURPOSE: The absence of an adequate volume of bone at implant sites requires augmentation procedures before the placement of implants. The aim of the present study was to assess the ridge width gain with the use of allografts and biphasic ß-tricalcium phosphate with hydroxyapatite (alloplast) in ridge split procedures, when each were used in small (0.25 to 1 mm) and large (1 to 2 mm) particle sizes. PATIENTS AND METHODS: A randomized controlled trial of 23 subjects with severe atrophy of the mandible in the horizontal dimension was conducted in a private institute. The patients underwent placement of 49 dental implants after a staged ridge split procedure. The patients were randomly allocated to alloplast and allograft groups (predictor variable). In each group, the patients were randomly assigned to either small graft particle or large graft particle size (predictor variable). The gain in ridge width (outcome variable) was assessed before implant placement. A 2-way analysis of variance test and the Student unpaired t test were used for evaluation of the ridge width gain between the allograft and alloplast groups (predictor variable). Differences were considered significant if P values were < .05. RESULTS: The sample included 23 patients (14 men and 9 women). The patients were randomly allocated to the alloplast (n = 11) or allograft (n = 12) group before the ridge split procedure. In each group, they were assigned to a small graft particle or large graft particle size (alloplast group, small particle in 5 and large particle size in 6 patients; allograft group, small particle in 6 and large particle size in 6). A statistically significant difference was observed between the 2 graft types. The average ridge width gain was significantly greater in the alloplast group (large, 4.40 ± 0.24 mm; small, 3.52 ± 0.59 mm) than in the allograft group (large, 3.82 ± 0.19 mm; small, 2.57 ± 0.16 mm). For both graft types (alloplast and allograft), the large particle size graft resulted in a greater ridge width gain compared with the small particle size graft (P < .05). CONCLUSIONS: Within the limitations of the present study, we suggest the use of large particle alloplast as the graft material of choice for staged ridge split procedures in the posterior mandible.

Effect of newly developed pigments and ultraviolet absorbers on the color change of pigmented silicone elastomer.

AIM AND OBJECTIVE: The aim and objective of the study is to evaluate effect of ultraviolet (UV) stabilizer (UV absorber Chimassorb 81) on color change of pigmented silicone elastomer when commercially available (red and yellow), and newly developed pigments (sicotrans red and sicopal brown) were used. MATERIALS AND METHODS: Two commercially available pigments - red (P112 Brilliant Red) and yellow (P106 Yellow) and two newly developed pigments - sicotrans red and sicopal brown were studied. In total eight groups made up of nine samples each were fabricated using elastomer with the combinations of the above pigments and UV stabilizer (Chimassorb 81). Groups 1, 3, 5, and 7 contain elastomer in combination with sicotrans red, sicopal brown, yellow and red pigments, respectively. Similarly, groups 2, 4, 6, and 8 along with elastomer and pigments (sicotrans sed, sicopal brown, yellow and red, respectively) contain the UV stabilizer (Chimassorb 81). Samples were subjected to aging in an accelerated weathering chamber (Weather-Ometer). Color values CIE (Commission Internationale d'Eclairage) L*, a*, and b * were measured at baseline and after 1000 h of weathering. Change in color (Delta E) was calculated. RESULTS: All groups showed a significant color change at 1000 h. Groups 1, 2, 3, and 4 showed a statistically significant less change in both colors (sico trans red and sicopal brown) compared to groups 5,6,7, and 8 (commercial pigments-Red and Yellow). Overall, the change in the color in groups with the UV stabilizer (Chimassorb) was less when compared to the groups where the stabilizer was not used. CONCLUSION: The newly developed pigment led to increased color stability as compared to commercially available pigments. Addition of UV stabilizer, Chimassorb led to a further reduction in color change of the pigmented elastomer.

Comparison of photographic and conventional methods for tooth shade selection: A clinical evaluation.

AIM: This study aimed to compare three different methods used for shade selection, i.e., visual method, spectrophotometer, and digital photography method. MATERIALS AND METHODS: Fifty participants were selected from the Out Patient Department of Prosthodontics. Presence of the maxillary right central incisor with no history of any restorative or endodontic procedures was the primary inclusion criterion. The shade of the right maxillary central incisor was determined using all the three shade selection procedures, namely, visual, spectrophotometric, and digital photography method for all the selected participants. The shades obtained in the visual method using a shade guide were noted down for further comparisons. The spectrophotometer reported the L*, a*, and b* values along with the actual shade whereas the digital photography method reported only the L*, a*, and b* values. The agreement between the readings obtained by the three different methods was compared and subjected to appropriate statistical analysis. RESULTS: The results showed that when the three methods studied were compared, there was a statistically significant proportion of agreement between spectrophotometric and visual method (P < 0.01) with higher proportion of "yes" (agreement) and between the spectrophotometric and digital photography method (P < 0.01) with higher proportion of "yes" (agreement). Coefficient of agreement (using Kappa coefficient) between spectrophotometric and visual shades revealed a fair agreement. The mean ΔE was 1.69. There was a statistically significant difference between the proportion of ΔE more than and <2, between spectrophotometric and digital photography methods (P < 0.01) with higher proportion of <2 ΔE. Furthermore, percentage of agreement between shades obtained by the visual and spectrophotometric method showed maximum agreement with A1 shade. CONCLUSION: It was concluded that the digital photography method emerged as a reliable method for shade selection in a clinical setup.

Reliability of Resonance Frequency Analysis as an Indicator of Implant Micromotion: An In Vitro Study.

PURPOSE: To assess validity and reliability of resonance frequency analysis (RFA) as an indicator of implant micromotion (MM) in implants of different lengths and thread designs. MATERIALS AND METHODS: Two types of implants were studied-An implant with an asymmetrical, self-tapping thread design, varying thread pitch and geometry (Myriad Plus; Equinox Medical Technology, Amersfoort, The Netherlands) and a tapered implant with a proprietary buttress thread design (Tapered Internal; BioHorizon). MM was assessed for 2 implant lengths (Myriad-Plus 3.8 × 13 and 3.8 × 9.5 mm) and 2 designs (Myriad-Plus 3.8 × 9.5 mm and BioHorizon 3.8 × 9 mm). Ten implants of each group were inserted in fresh bovine bone of uniform bone density. Insertion torque (IT), implant stability quotient (ISQ), and MM were measured using protocol described in the literature. RESULTS: Longer implants showed reduced IT, RFA values, and MM compared with shorter implants (P < 0.01). BioHorizon implants showed similar IT, significantly higher ISQ values (P < 0.01), yet higher MM (P < 0.01). CONCLUSION: Implant length and macrodesign affect ISQ, MM, and IT. Clinical measurements (ISQ) and IT have limited value as an indicator of implant MM.

Three-Dimensional Evaluation of Alveolar Bone and Soft Tissue Dimensions of Maxillary Central Incisors for Immediate Implant Placement: A Cone-Beam Computed Tomography Assisted Analysis.

INTRODUCTION: This study explored the relationship between the thickness of bone and soft tissue along the labial and palatal aspect of maxillary central incisors. The influence of overall socket width, labiopalatal positioning of the incisor on the bone, and soft tissue thickness were also investigated. MATERIALS AND METHODS: This study used cone-beam computed tomography of 150 patients to determine labial, palatal soft and hard tissue thickness, labiopalatal (B-P) socket width and corelated the same to the labiopalatal positioning of maxillary central incisors. RESULTS: Mean (SD) thicknesses of the labial soft tissue at cervical (C), midroot (M), and apical (A) locations and the corresponding bone thicknesses were 1.07 (0.28), 0.987 (0.27), 1.240 (0.41), and 0.928 (0.39), 0.894 (0.52), 1.57 (0.88), respectively. Similarly, palatal soft tissue and bone thicknesses at locations C, M, A were 1.807 (0.66), 1.557 (0.62), 1.639 (0.66), and 1.679 (0.62), 3.439 (1.28), 6.038 (1.63), respectively. Mean (SD) thicknesses of the B-P socket width at location C was 8.047 (0.963). CONCLUSIONS: There is a positive correlation between the labial and palatal bone and corresponding soft tissue thickness, between thickness of the labial bone and the labiopalatal thickness of the alveolar socket. No correlation was observed between the thickness of the labial cortical bone and the labiopalatal positioning of the tooth.

The Anatomic Inter Relationship of the Neurovascular Structures Within the Inferior Alveolar Canal: A Cadaveric and Histological Study.

OBJECTIVE: The location and inter relationship of the structures of the inferior alveolar neurovascular bundle within the mandibular canal has not been clearly defined. The knowledge of the same is important while planning surgeries in the posterior mandible. METHODS: Eight cadaveric mandibles were dissected and sections were made at the distal aspect of every tooth. The inferior alveolar neurovascular bundle was identified and examined for the location of the inferior alveolar artery, vein and nerve. Hematoxylin and Eosin sections were made for each specimen to confirm the position of these structures. RESULTS: All the sections in all the specimens confirmed that a blood vessel lies superior to the nerve. This position appeared consistent in all the positions relative to all the posterior teeth. There was a variation in the bucco-lingual positioning of these structures relative to each other for the various mandibles. CONCLUSION: A blood vessel is found to always lie superior to the inferior alveolar nerve within the mandibular canal. Variations in the inter relationship of the structures is present. SIGNIFICANCE: This cadaveric study proves that all along the course of the neurovascular bundle, at various cross-sections studied, the inferior nerve is always inferior to a blood vessel. There can be great variations to the positioning of the structures within the neurovascular bundle in the bucco-lingual dimension and also in the exit of the nerve in various mandibles. Knowledge of the location of the structures is of importance during surgical procedures carried out in the vicinity of these structures.

Easy Accurate Transfer of the Sculpted Soft Tissue Contours to the Working Cast: A Clinical Tip.

Tooth replacement in the esthetic zone presents a myriad of challenges for the clinician. An ovate pontic accurately duplicates the emergence profile of the natural tooth it replaces in order to provide an esthetic, yet cleansable prosthesis. The accurate transfer of this sculpted tissue beneath the pontic of the provisional restoration is critical to provide the dental laboratory technician with the necessary information to fabricate a definitive restoration with an appropriate emergence profile. This article presents an innovative, simple and convenient impression technique for easy and accurate transfer of the tissue contours to the working cast, avoiding tissue collapse and tissue compression produced due to the impression material.