Effects of Grafting Degree on the Formation of Waterborne Polyurethane-Acrylate Film with Hard Core-Soft Shell Structure.

Waterborne polyurethane-acrylate (WPUA) grafted with polyurethane was prepared to improve the film-forming ability of hard-type acrylic latex. To balance the film-formation ability and hardness, the WPUA latex was designed with a hard core (polyacrylate) and soft shell (polyurethane). The grafting ratio was controlled through varying the content of 2-hydroxyethyl methacrylate (HEMA) used to cap the ends of the polyurethane prepolymer. The morphologies of the latex particles, film surface, and fracture surface of the film were characterized through transmission electron microscopy, atomic force microscopy, and scanning electron microscopy, respectively. An increase in the grafting ratio resulted in the enhanced miscibility of polyurethane and polyacrylate but reduced adhesion between particles and increased minimum film formation temperature. In addition, grafting was essential to obtain transparent WPUA films. Excessive grafting induced defects such as micropores within the film, leading to the decreased hardness and adhesive strength of the film. The optimal HEMA content for the preparation of a WPUA coating with excellent film-forming ability and high hardness in ambient conditions was noted to be 50%. The final WPUA film was prepared without coalescence agents that generate volatile organic compounds.

Dual-Cure Adhesives Using a Newly Synthesized Itaconic Acid-Based Epoxy Acrylate Oligomer.

Herein, a novel biomass-derived itaconic acid (IA)-based epoxy acrylate oligomer (EAO) is synthesized by means of the esterification reaction of the epoxy group of bisphenol A diglycidyl ether (BADGE) with the carboxylic group of IA. The detailed chemical structure of the as-prepared bisphenol A diglycidyl ether diitaconate (BI) is characterized via the KOH value, FT-IR spectrum, and 1H-NMR spectrum. Further, a dual-cure adhesive system is formulated using BADGE, acrylic acid, and trimethylolpropane triacrylate with various BI contents, and the adhesive performance is investigated by measuring the thermal stability, adhesive properties, pencil hardness, and surface energy properties. Thus, the dual-cure adhesive with a BI content of 0.3 mol is shown to provide excellent thermal stability, along with an adhesive strength of 10.7 MPa, a pencil hardness of 2H, and a similar surface energy to that of a typical polycarbonate film. In addition, the properties of the BI-based dual-cure adhesive are compared with those of the dual-cure adhesives based on bisphenol A glycerolate diacrylate or bisphenol A glycerolate dimethacrylate.

Enhanced Mechanical and Thermal Properties of Chain-Extended Waterborne Polyurethane Coatings with Cellulose Acetate Butyrate.

A series of waterborne polyurethane (WPU) dispersions were prepared by chain-extending a prepolymer made of polyester diol, isophorone diisocyanate, and dimethylol propionic acid using cellulose acetate butyrate (CAB). The particle size and viscosity of the WPU dispersion were measured. In addition, we investigated the effects of CAB on the thermal, mechanical, and optical properties of WPU films. The use of CAB effectively improved the crosslinking degree of the WPUs, increasing the thermal stability and water resistance of the corresponding films. In particular, CAB increased the tensile strength of the WPU films up to 67%, while maintaining their elongation at break unchanged. In addition, CAB improved the optical transmittance by reducing the microphase separation between the soft and hard segments of PU. The rough surface structure of the WPU films formed by CAB led to improved matting properties.

Computational Approach to the Surface-Crosslinking Process of Superabsorbent Polymer via Central Composite Design.

The improvement of gel strength and absorption properties through the surface-crosslinking of superabsorbent polymers (SAPs) is essential for sanitary industry applications. We prepared core-SAP via aqueous solution copolymerization, and then surface-crosslinked the core-SAP under various conditions. The structure of the SAP was characterized using Fourier transform infrared (FT-IR) spectroscopy. Central composite design (CCD) of response surface methodology (RSM) has been applied to determine the optimum surface-crosslinking conditions such as surface-crosslinker content, reaction temperature, and reaction time. The optimal surface-crosslinking conditions were identified at a surface-crosslinker content of 2.22 mol%, reaction temperature of 160 °C, and reaction time of 8.7 min. The surface-crosslinked SAP showed excellent absorbency under load of 50 g/g with a permeability of 50 s. Other absorption properties were also evaluated by measuring the free absorbency and centrifuge retention capacity in saline solution.