Measurement of the birefringence variation induced by dihydrogen diffusion into a polarization-maintaining fiber.

We report continuous measurements of the transmission spectrum of a fiber loop mirror interferometer composed of a Panda-type polarization-maintaining (PM) optical fiber during the diffusion of dihydrogen (H2) gas into the fiber. Birefringence variation is measured through the wavelength shift of the interferometer spectrum when the PM fiber is inserted into a gas chamber with H2 concentration from 1.5 to 3.5 vol.% at 75 bar and 70°C. The measurements correlated with simulation results of H2 diffusion into the fiber lead to a birefringence variation of -4.25 × 10-8 per mol m-3 of H2 concentration in the fiber, with a birefringence variation as low as -9.9×10-8 induced by 0.031 µmol m-1 of H2 dissolved in the single-mode silica fiber (for 1.5 vol.%). These results highlight a modification of the strain distribution in the PM fiber, induced by H2 diffusion, leading to a variation of the birefringence that could deteriorate the performances of fiber devices or improve H2 gas sensors.

Plasmonic biosensing with tilted fiber Bragg gratings interrogated using a 512-pixel spectrometer.

Plasmonic tilted fiber Bragg gratings (TFBGs) are very efficient for fast, accurate, and minimally invasive biosensing. Their transmitted amplitude spectrum is a dense comb of narrowband cladding mode resonances (full width at half maximum < 1 nm) that is usually demodulated using highly resolved (wavelength resolution < 10 pm) devices. This work demonstrates the possibility of using a coarsely resolved spectrometer (166 pm) to read out the amplitude spectrum of a gold-coated TFBG. A refined analysis of the spectral content has allowed us to develop signal processing that provides a refractometric sensitivity of 2656 nm/RIU. This is a fivefold improvement compared to previously reported read-out techniques. Biosensing has then been successfully implemented with gold-coated TFBGs implemented in reflection mode for the detection of insulin, with specific antibodies grafted on the gold surface. Our experimental work is a first step toward the industrialization of the FBG technology, as it opens the door to fast parallel biosensing, profiting from the multiple sensing channels (up to 64) of the interrogator and its high processing speed (repetition rate up to 3 kHz).

Smart Railway Traffic Monitoring Using Fiber Bragg Grating Strain Gauges.

There is today ample evidence that fiber Bragg gratings (FBGs) distributed along a railway track can provide robust axle counting and bring numerous assets compared to competing technologies in this practical environment. This work brings two relevant originalities with respect to the state-of-the-art solutions. First, a study of the strain distribution in the rail cross-section is performed to determine the sensitivity according to the charge and the position on the rail. Secondly, the technology is deployed along the rail track as a smart object where the sensor head is composed of four FBG wavelength-division-multiplexed in a single telecommunication-grade optical fiber and interrogated by a miniaturized read-out device. Two FBGs ensure the detection of the train direction and another two bring the required redundancy to reach a safety integrity level (SIL) 4. The read-out unit has been specifically developed for the application and contains a vertical-cavity surface-emitting laser (VCSEL) and a photodiode driven by a high-speed microprocessor unit that processes the data and communicates the useful information, i.e., the number of axles. On-field tests confirm that the proposed approach makes the installation process easier while it democratizes the technology.

Ultra-fast fiber Bragg grating inscription in CYTOP polymer optical fibers using phase mask and 400 nm femtosecond laser.

Fiber Bragg gratings (FBGs) in cyclic transparent fluoropolymer (CYTOP) optical fiber are the subject of a lot of research as they can be of interest for many applications, such as temperature, humidity, strain, and radiation sensing. We report here a new technique to produce high quality FBGs in CYTOP fiber. It uses a femtosecond laser system operating at 400 nm and a phase mask. In contrast to previously reported results, the gratings are obtained in a few seconds with a writing power as low as 80 µW. With this setup, 2 mm-long gratings with reflectivity up to 92 % and full width at half maximum bandwidth around 0.5 nm were obtained in less than 10 s. The resonance wavelengths of the FBGs are confirmed by numerical computation in the graded-index multimode CYTOP fiber, and the mode selection characteristic of FBGs in CYTOP is investigated. Finally, the temperature sensitivity of CYTOP FBG is measured in different mode groups for heating up and cooling down, showing values independent of the mode group measured, but with a small hysteresis.

800 nm femtosecond pulses for direct inscription of FBGs in CYTOP polymer optical fiber.

We report the inscription of highly reflective fiber Bragg gratings in perfluorinated polymer (CYTOP) optical fibers using 800 nm femtosecond pulses and a line-by-line inscription method. We demonstrate that the energy for grating inscription without damage is below 27 nJ. After the writing process, we show that the grating reflectivity continues to rise for several hours. The obtained gratings show reflectivity degradation with temperature increase, while the Bragg wavelength undergoes a linear temperature dependence of 37.7 pm/°C when the humidity is controlled and the heating/cooling rate is relatively low (≤0.14∘C/min). The humidity sensitivity at a fixed temperature (25°C) is 22.3 pm/%RH. Finally, the axial strain sensitivity is determined to be 1.35 pm/µÉ›.

Implementation of a Mobile Platform Based on Fiber Bragg Grating Sensors for Automotive Traffic Monitoring.

Instrumentation techniques, implementation and installation methods are major concerns in today's distributed and quasi-distributed monitoring applications using fiber optic sensors. Although many successful traffic monitoring experiments have been reported using Fiber Bragg Gratings (FBGs), there has been no standardized solution proposed so far to have FBG seamlessly implemented in roads. In this work, we investigate a mobile platform including FBG sensors that can be positioned on roads for the purpose of vehicle speed measurements. The experimental results prove the efficiency of the proposed platform, providing a perspective toward weigh-in-motion systems.

Design of an endomicroscope including a resonant fiber-based microprobe dedicated to endoscopic polarimetric imaging for medical diagnosis.

We report on a novel endomicroscope, to the best of our knowledge, designed for achieving full 4×4 Mueller polarimetric images of biological tissues through a fiber endoscope for medical diagnosis. The polarimetric technique is based on a previously published two-wavelength differential method (TWDM). A key component of the endomicroscope is a resonant fiber-based microprobe including a highly-selective fiber Bragg grating (FBG), free of detrimental polarimetric effects, photo written in the core of the fiber, near the output face. By means of the TWDM, and using the specially designed microprobe (diameter 2.9 mm, length 30 mm), full Mueller images of 250×250 pixels were produced at the rate of 1 image/2 s through a 2 m single mode fiber, paving the way to in vivo applications in polarimetric endomicroscopy.

Fiber Bragg grating characterization using factorial design.

The design of the experiment is a scientific approach that provides the maximum amount of information with the minimum number of experiments. It is applicable in scientific and industrial research. We represent a three-variable two-level factorial design to assess fiber Bragg grating properties under simultaneous temperature, humidity, and strain stimuli. Three uniform gratings were inscribed in a single-mode standard optical fiber using the interferometric technique. Two gratings were recoated, one with acrylate and another with a layer of polyimide, while the third grating remained bare. With only eight measuring points, the sensitivities of temperature, strain, and humidity were computed. Moreover, with this technique, the cross-sensitivities between temperature and strain, temperature and humidity, humidity and strain, and between all three factors could also be quantified. We have proven that the results of this design are comparable with those of the classic method. For all gratings, the temperature and strain sensitivities were obtained in the order of 10 pm/°C and 1.1 pm/µÎµ, respectively. The humidity sensitivity of the polyimide recoated grating was estimated to be in the order of 4.47 pm/%RH at room temperature.

Fiber Bragg grating regeneration at 450°C for improved high temperature sensing.

Type-I fiber Bragg gratings photo-inscribed in hydrogen-loaded B/Ge co-doped silica single-mode optical fibers have been regenerated efficiently at 450°C, which is the lowest temperature reported so far. The mechanical strength of the annealed fiber is preserved while ensuring temperature sensing of the regenerated gratings up to 900°C. Unlike low temperature cycles (≤600°C), an annealing process at higher temperatures revealed faster regeneration for strong gratings. Changes in grating strength were also measured before the regeneration cycle. These behaviors suggest the contribution of different mechanisms to the regeneration process with different relative dynamics.

CYTOP Fibre Bragg Grating Sensors for Harsh Radiation Environments.

We present a polymer fibre Bragg grating sensor and its sensitivity to gamma radiation by observing the reflected spectral profile. The Bragg grating is femtosecond inscribed within a perfluorinated CYTOP fibre and the alteration of the Bragg wavelength corresponds to the total radiation dose received. Over a total dose of 41 k Gy, the fibre demonstrates a sensitivity of - 26.2 p m / k Gy and a resolution of 40 Gy. Under active consideration for the instrumentation of nuclear waste repositories, this study gives a better understanding of the effects of gamma radiation upon Bragg gratings in CYTOP fibres.

Effect of hydrogen gas on FBG-based optical fiber sensors for downhole pressure and temperature monitoring.

The influence of hydrogen gas on Fiber Bragg Grating (FBG)-based optical fiber sensors has been validated experimentally. More in particular, the focus was on FBGs written in the so-called Butterfly Micro Structured Fiber that targets simultaneous pressure and temperature monitoring with a minimum in cross-sensitivity to be used in, for example, downhole applications for the oil and gas market. The hydrogen-induced pressure and temperature errors from this type of sensor have been quantified as a function of the partial hydrogen pressure. The induced errors can be related to the diffusion of the hydrogen into the microstructure and to refractive index changes due to the presence of the hydrogen in the micro holes and penetration of it into the fiberglass. Furthermore, we have also shown that the hydrogen-induced errors scale with the partial hydrogen pressure.

Bragg grating inscription in PMMA optical fibers using 400-nm femtosecond pulses.

In this Letter, we report the fast growth of high quality uniform Bragg gratings in trans-4-stilbenemethanol (TS)-doped poly(methyl methacrylate) (PMMA) step-index optical fibers. Grating manufacturing was obtained using a 400 nm femtosecond pulsed laser and a 1060-nm-period uniform phase mask. For 20 mW mean laser beam power, the grating reflectivity reaches 98% in ∼60 s.

BDK-doped core microstructured PMMA optical fiber for effective Bragg grating photo-inscription.

An endlessly single-mode doped microstructured poly(methyl methacrylate) (PMMA) optical fiber is produced for effective fiber Bragg grating (FBG) photo-inscription by means of a 400 nm femtosecond pulsed laser and the phase mask technique. The fiber presents a uniform benzyl dimethyl ketal (BDK) distribution in its core without drastic loss increase. It was produced using the selected center hole doping technique, and the BDK dopant acts as a photoinitiator. In this Letter, we report a rapidly growing process of the grating reflection band. For an 11 mW mean laser power, the FBG reflectivity reaches 83% in only 40 s.

Negative axial strain sensitivity in gold-coated eccentric fiber Bragg gratings.

New dual temperature and strain sensor has been designed using eccentric second-order fiber Bragg gratings produced in standard single-mode optical fiber by point-by-point direct writing technique with tight focusing of 800 nm femtosecond laser pulses. With thin gold coating at the grating location, we experimentally show that such gratings exhibit a transmitted amplitude spectrum composed by the Bragg and cladding modes resonances that extend in a wide spectral range exceeding one octave. An overlapping of the first order and second order spectrum is then observed. High-order cladding modes belonging to the first order Bragg resonance coupling are close to the second order Bragg resonance, they show a negative axial strain sensitivity (-0.55 pm/µÎµ) compared to the Bragg resonance (1.20 pm/µÎµ) and the same temperature sensitivity (10.6 pm/°C). With this well conditioned system, temperature and strain can be determined independently with high sensitivity, in a wavelength range limited to a few nanometers.

Direct transverse load profile determination using the polarization-dependent loss spectral response of a chirped fiber Bragg grating.

The determination of stress profiles created by transverse loads was proved to be important in different domains, such as structural health monitoring and biomechanics, and, more specifically, in the prostheses domain. In this paper, we report an original method to estimate the transverse load profile from the polarization-dependent loss (PDL) spectrum of a chirped fiber Bragg grating (CFBG). This method makes use of the relationship between the integration of the PDL of a CFBG, and the force profile has the advantage of not requiring any iterative method to estimate the transverse load profile. The relationship linking the integration of the PDL and the force profile is demonstrated using an analytical approximation of the transmission spectrum of CFBGs. The validity of this method for the determination of non-uniform load profiles is then shown using a numerical analysis. An experimental demonstration is finally reported using a 48 mm-long CFBG subject to different step transverse load profiles.

Control over photo-inscription and thermal annealing to obtain high-quality Bragg gratings in doped PMMA optical fibers.

Bragg gratings are photo-inscribed in trans-4-stilbenemethanol doped PMMA fibers using a 325 nm He-Cd laser and a phase mask. Two distinct behaviors are reported depending on the laser power density. In the high-density regime with 637 mW/mm2, the grating reflectivity is stable over time after the writing process, but the reflected spectrum is of limited quality, as the grating length is limited to the laser width (1.2 mm). The beam is then enlarged to 6 mm, decreasing the power density to 127 mW/mm2. In this case, the grating reflectivity strongly decays after the writing process. A fortunate property here results from the recovery of the initial reflectivity using a post-inscription thermal annealing. Both behaviors are attributed to the evolution between trans- and cis-isomers.

Review of Trackside Monitoring Solutions: From Strain Gages to Optical Fibre Sensors.

A review of recent research on structural monitoring in railway industry is proposed in this paper, with a special focus on stress-based solutions. After a brief analysis of the mechanical behaviour of ballasted railway tracks, an overview of the most common monitoring techniques is presented. A special attention is paid on strain gages and accelerometers for which the accurate mounting position on the track is requisite. These types of solution are then compared to another modern approach based on the use of optical fibres. Besides, an in-depth discussion is made on the evolution of numerical models that investigate the interaction between railway vehicles and tracks. These models are used to validate experimental devices and to predict the best location(s) of the sensors. It is hoped that this review article will stimulate further research activities in this continuously expanding field.

Surface plasmon resonance in eccentric femtosecond-laser-induced fiber Bragg gratings.

Highly localized refractive index modulations are photo-written in the core of pure silica fiber using point-by-point focused UV femtosecond pulses. These specific gratings exhibit a comb-like transmitted amplitude spectrum, with polarization-dependent narrowband cladding mode resonances. In this work, eccentric gratings are surrounded by a gold sheath, allowing the excitation of surface plasmon polaritons (SPP) for radially-polarized light modes. The spectral response is studied as a function of the surrounding refractive index and a maximum sensitivity of 50 nm/RIU (refractive index unit) is reported for a well-defined cladding-mode resonance among the spectral comb. This novel kind of plasmonic fiber grating sensor offers rapidity of production, design flexibility, and high temperature stability.

Fiber Bragg grating sensors toward structural health monitoring in composite materials: challenges and solutions.

Nowadays, smart composite materials embed miniaturized sensors for structural health monitoring (SHM) in order to mitigate the risk of failure due to an overload or to unwanted inhomogeneity resulting from the fabrication process. Optical fiber sensors, and more particularly fiber Bragg grating (FBG) sensors, outperform traditional sensor technologies, as they are lightweight, small in size and offer convenient multiplexing capabilities with remote operation. They have thus been extensively associated to composite materials to study their behavior for further SHM purposes. This paper reviews the main challenges arising from the use of FBGs in composite materials. The focus will be made on issues related to temperature-strain discrimination, demodulation of the amplitude spectrum during and after the curing process as well as connection between the embedded optical fibers and the surroundings. The main strategies developed in each of these three topics will be summarized and compared, demonstrating the large progress that has been made in this field in the past few years.

Fast thermal regeneration of fiber Bragg gratings.

In this Letter we report a fast thermal regeneration of Type I fiber Bragg gratings inscribed with a UV laser in up to four different optical fibers: hydrogenated standard fiber, hydrogenated highly Ge-doped fiber, hydrogenated photosensitive fiber, and nonhydrogenated fiber. The thermal treatment consists in directly introducing the optical fiber into a preheated oven. The preheat temperature depends on the type of fiber used and is high enough to erase the grating and regenerate it afterward. The best results are obtained with hydrogenated photosensitive fiber and highly Ge-doped fiber, whereas no satisfactory results were obtained with hydrogenated standard fiber and nonhydrogenated photosensitive fiber. A regenerated grating with only 1.6 dB of loss was obtained in 10 min, reducing the time needed by a factor of 5.7. By adjusting the temperature of the oven, regenerated gratings of 13.7 dB of loss in 31 s and 5.8 dB of loss in 3 min were obtained. The factors of improvement in time are 110.3 and 19, respectively.