Integrating Navajo Pottery Techniques To Improve Silver Nanoparticle-Enabled Ceramic Water Filters for Disinfection.

Point-of-use treatment technologies can increase access to safe drinking water in rural areas. Sustained use of these technologies is uncommon due to oversight of community needs, user-perceived risks, long-term maintenance, and conflict with traditional practices. Nanosilver-enabled ceramic water filters are unique due to the use of locally sourced materials available at or near the target community; however, technical limitations persist (e.g., nanosilver's uncontrolled release and passivation from sulfide or chloride). This work aims to overcome these limitations by impregnating nanosilver onto ceramics with a Navajo pottery rosin, collected from pinyon trees with a third-generation artisan. Here, we investigate this sustainable and novel material for drinking water treatment; the study ranges from a proof of concept to testing under realistic conditions. Results show that when embedded in a thin film, the biopolymer controlled ionic silver dissolution and prevented silver passivation from sulfide and chloride. When applied to ceramic filters, the biopolymer effectively immobilized nanosilver in a range of waters. Over a 25 day study to emulate household-use conditions, this coating method sustained disinfection of a coculture of Gram-positive and Gram-negative bacteria while controlling biofouling. Overall, the use of this Navajo pottery material can facilitate adoption while providing the needed technological advancement to these widely used treatment devices.

Protozoan-Priming and Magnesium Conditioning Enhance Legionella pneumophila Dissemination and Monochloramine Resistance.

Opportunistic pathogens (OPs) are of concern in drinking water distribution systems because they persist despite disinfectant residuals. While many OPs garner protection from disinfectants via a biofilm lifestyle, Legionella pneumophila (Lp) also gains disinfection resistance by being harbored within free-living amoebae (FLA). It has been long established, but poorly understood, that Lp grown within FLA show increased infectivity toward subsequent FLA or human cells (i.e., macrophage), via a process we previously coined "protozoan-priming". The objectives of this study are (i) to identify in Lp a key genetic determinant of how protozoan-priming increases its infectivity, (ii) to determine the chemical stimulus within FLA to which Lp responds during protozoan-priming, and (iii) to determine if more infectious forms of Lp also exhibit enhanced disinfectant resistance. Using Acanthamoeba castellanii as a FLA host, the priming effect was isolated to Lp's sidGV locus, which is activated upon sensing elevated magnesium concentrations. Supplementing growth medium with 8 mM magnesium is sufficient to produce Lp grown in vitro with an infectivity equivalent to that of Lp grown via the protozoan-primed route. Both Lp forms with increased infectivity (FLA-grown and Mg2+-supplemented) exhibit greater monochloramine resistance than Lp grown in standard media, indicating that passage through FLA not only increases Lp's infectivity but also enhances its monochloramine resistance. Therefore, laboratory-based testing of disinfection strategies should employ conditions that simulate or replicate intracellular growth to accurately assess disinfectant resistance.

Human-Infrastructure Interactions during the COVID-19 Pandemic: Understanding Water and Electricity Demand Profiles at the Building Level.

When engineers design and manage a building's water and electricity utilities, they must make assumptions about resource use. These assumptions are often challenged when unexpected changes in demand occur, such as the spatial and temporal changes observed during the coronavirus (COVID-19) pandemic. Social distancing policies (SDPs) enacted led many universities to close their campuses and implement remote learning, impacting utility consumption patterns. Yet, little is known about how consumption changed at the building level. Here, we aim to understand how water and electricity consumption changed during the pandemic by identifying characteristic weekly demand profiles and understanding how these changes were related to regulatory and social systems. We performed k-means clustering on utility demand data measured before and as the pandemic evolved from five buildings of different types at the University of Texas at Austin. As expected, after SDPs were enacted both water and electricity use shifted, with most buildings seeing a sharp initial decline that remained low until the university partially reopened. In contrast to electricity use, we found that water use was tightly coupled with SDPs. Our study provides actionable information for managers to mitigate negative impacts (e.g., water stagnation) and capitalize on opportunities to minimize resource use.

Development of a reproducible method for monitoring SARS-CoV-2 in wastewater.

Monitoring the genetic signal of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) through RNA titers in wastewater has emerged as a promising strategy for tracking community-scale prevalence of coronavirus disease 2019 (COVID-19). Although many studies of SARS-CoV-2 in wastewater have been conducted around the world, a uniform procedure for concentrating the virus in wastewater is lacking. The goal of this study was to comprehensively evaluate how different methods for concentrating the suspended solids in wastewater affect the associated SARS-CoV-2 RNA signal and the time required for processing samples for wastewater-based epidemiology efforts. We additionally consider the effects of sampling location in the wastewater treatment train (i.e., following preliminary or primary treatment), pasteurization, and RNA extraction method. Comparison of the liquid phase to suspended solids obtained via centrifugation or vacuum filtration suggests that the RNA signal of SARS-CoV-2 preferentially occurs in the solids. Therefore, we assert that the recovery of SARS-CoV-2 from wastewater should focus on suspended solids. Our data indicate that the measured SARS-CoV-2 signal is higher among samples taken from the primary clarifier effluent, as opposed to those taken after preliminary treatment. Additionally, we provide evidence that sample pasteurization at 60 °C for 90 min reduces the SARS-CoV-2 signal by approximately 50-55%. Finally, the results indicate that a magnetic bead approach to RNA extraction leads to a higher SARS-CoV-2 signal than does a silica membrane approach.

Implications of Social Distancing Policies on Drinking Water Infrastructure: An Overview of the Challenges to and Responses of U.S. Utilities during the COVID-19 Pandemic.

Social distancing policies (SDPs) implemented throughout the United States in response to COVID-19 have led to spatial and temporal shifts in drinking water demand and, for water utilities, created sociotechnical challenges. During this unique period, many water utilities have been forced to operate outside of design conditions with reduced workforce and financial capacities. Few studies have examined how water utilities respond to a pandemic; such methods are even absent from many emergency response plans. Here, we documented how utilities have been impacted by the COVID-19 pandemic. We conducted a qualitative analysis of 30 interviews with 53 practitioners spanning 28 U.S. water utilities. Our aim was to, first, understand the challenges experienced by utilities and changes to operations (e.g., demand and deficit accounts) and, second, to document utilities' responses. Results showed that to maintain service continuity and implement SDPs, utilities had to overcome various challenges. These include supply chain issues, spatiotemporal changes in demand, and financial losses, and these challenges were largely dependent on the type of customers served (e.g., commercial or residential). Examples of utilities' responses include proactively ordering extra supplies and postponing capital projects. Although utilities' adaptations ensured the immediate provision of water services, their responses might have negative repercussions in the future (e.g., delayed projects contributing to aging infrastructure).

Role of Electrostatics in the Heterogeneous Interaction of Two-Dimensional Engineered MoS2 Nanosheets and Natural Clay Colloids: Influence of pH and Natural Organic Matter.

Few-layered molybdenum disulfide (MoS2) nanosheets are poised to be at the core of low-voltage electronic device development. Upon environmental release, these two-dimensional (2D) structures can interact with abundant natural geocolloids. This study probes the role of dimensionality in modulating the aggregation behavior of 2D MoS2 nanosheets with plate-like geocolloids (i.e., homoionized kaolinite and montmorillonite clays). MoS2 nanosheets were exfoliated using an ethanol/water mixture, and aggregation kinetics were investigated with time-resolved dynamic light scattering at low monovalent salt concentrations and at three pH levels, in the presence and absence of Suwannee River humic acid (SRHA). Results indicate that pH and particle ratios are key to modulating the stability of MoS2/clay systems. At pH 4, aggregation of MoS2 increased with increasing MoS2/clay ratios and approached maximum values of 0.09 and 0.06 nm/s in the binary systems with montmorillonite and kaolinite, respectively. Electrostatic attraction facilitates heteroaggregation at pH values of 4 and 6; differences in the clay structures (i.e., face-face or face-edge aggregates) might explain the resulting MoS2/clay aggregate configurations, which were probed via the evolution of particle size distribution. The presence of only 0.1 mg/L SRHA drastically suppresses the heteroaggregation propensity of MoS2 nanosheets with geocolloids (to less than 0.01 nm/s at all pH values tested). The high stability of these heterogeneous systems under environmentally relevant conditions can increase the likelihood for cellular uptake and long-distance transport of MoS2.

A Structural Equation Model to Decipher Relationships among Water, Sanitation, and Health in Colonias-Type Unincorporated Communities.

The colonias along the United States-Mexico border are generally self-built neighborhoods of low-income families that lack basic infrastructure. While some government assistance has provided roads and electricity, water and wastewater services are still lacking in many colonias. This research is the first to collect a comprehensive dataset on water, sanitation, health, and living conditions in these unincorporated neighborhoods through collection of water samples and surveys; 114 households in 23 colonias across three geographically diverse Texas counties are studied. Water quality is assessed via traditional microbial indicators, chlorine, and arsenic. This complex dataset requires an advanced statistical tool to disentangle relationships among diverse factors. Structural equation modeling is utilized to identify relationships among surveyed and measured variables. The model reveals that colonias residents with well/hauled water accurately predict their water quality, while those with treated+piped water tend to think that their water is worse than it actually is. Dwelling quality and connection to sanitary sewers influence perceived health risks and household health, respectively. Furthermore, these communities have an overwhelming need and desire for point-of-use water treatment. This model can inform decision making and may be adapted to probe other questions and social dynamics for water and sanitation in unincorporated communities elsewhere.

Suspended multiwalled, acid-functionalized carbon nanotubes promote aggregation of the opportunistic pathogen Pseudomonas aeruginosa.

The increasing prevalence of carbon nanotubes (CNTs) as components of new functional materials has the unintended consequence of causing increases in CNT concentrations in aqueous environments. Aqueous systems are reservoirs for bacteria, including human and animal pathogens, that can form biofilms. At high concentrations, CNTs have been shown to display biocidal effects; however, at low concentrations, the interaction between CNTs and bacteria is more complicated, and antimicrobial action is highly dependent upon the properties of the CNTs in suspension. Here, impact of low concentrations of multiwalled CNTs (MWCNTs) on the biofilm-forming opportunistic human pathogen Pseudomonas aeruginosa is studied. Using phase contrast and confocal microscopy, flow cytometry, and antibiotic tolerance assays, it is found that sub-lethal concentrations (2 mg/L) of MWCNTs promote aggregation of P. aeruginosa into multicellular clusters. However, the antibiotic tolerance of these "young" bacterial-CNT aggregates is similar to that of CNT-free cultures. Overall, our results indicate that the co-occurrence of MWCNTs and P. aeruginosa in aqueous systems, which promotes the increased number and size of bacterial aggregates, could increase the dose to which humans or animals are exposed.

Seasonal contamination of well-water in flood-prone colonias and other unincorporated U.S. communities.

Many of the six million residents of unincorporated communities in the United States depend on well-water to meet their needs. One group of unincorporated communities is the colonias, located primarily in several southwestern U.S. states. Texas is home to the largest number of these self-built communities, of mostly low-income families, lacking basic infrastructure. While some states have regulations that mandate minimum infrastructure for these communities, water and sewage systems are still lacking for many of their residents. Unprotected wells and self-built septic/cesspool systems serve as the primary infrastructure for many such colonias. This research was designed to probe how wells and septic/cesspool systems are influenced by heavy rainfall events. Such events are hypothesized to impact water quality with regard to human health. Inorganic and microbiological water quality of the wells in nine colonias located in Nueces County, Texas, were evaluated during dry and wet periods. Nueces County was selected as an example based on its flooding history and the fact that many colonias there depend entirely on well-water and septic/cesspool systems. The results demonstrate that well-water quality in these communities varies seasonally with respect to arsenic (up to 35 µg/L) and bacterial contamination (Escherichia coli), dependent on the amount of rainfall, which leaves this population vulnerable to health risks during both wet and dry periods. Microbial community analyses were also conducted on selected samples. To explore similar seasonal contamination of well-water, an analysis of unincorporated communities, flooding frequency, and arsenic contamination in wells was conducted by county throughout the United States. This nationwide analysis indicates that unincorporated communities elsewhere in the United States are likely experiencing comparable challenges for potable water access because of a confluence of socioeconomic, infrastructural, and policy realities.

Water quality and associated microbial ecology in selected Alaska Native communities: Challenges in off-the-grid water supplies.

The availability of safe water for potable purposes in Alaska Native communities is limited due to naturally occurring metals and contaminants released from anthropogenic activities, such as drilling and mining. The impacts of climate change are magnified in the arctic and sub-arctic regions and thus have the potential to mobilize contaminants and exacerbate the water contamination problem. Alaska Native communities are vulnerable to such changes in their water quality because of their remote location and limited access to resources. This study initiates an assessment of water quality, including its microbial ecology, in off-the-grid Alaskan water supplies (i.e., primarily groundwater wells). In particular, water quality data were collected from nine communities (22 ground water wells). Water quality analyses included basic water quality parameters, a suite of metals relevant to human health, and microbial community composition. Results revealed location-specific elevated arsenic concentrations based on the underlying geological formation, particularly in the areas located in the geological formation of the McHugh Complex. Diverse microbial communities were observed, and the grouping appeared to be based on elevation. These findings present evidence of compromised water quality in an understudied area in the United States. The results from this study should be considered as a snapshot in time, which highlight the importance for further systematic studies in similar off-the-grid communities.

Applying biotechnology for drinking water biofiltration: advancing science and practice.

Drinking water biofiltration processes have evolved over time, moving from unintentional to deliberate, with careful filter media selection, nutrient and trace metal supplementation, oxidant amendment, and bioaugmentation of key microorganisms, to achieve improvements in water quality. Biofiltration is on the precipice of a revolution that aims to customize the microbial community for targeted functional outcomes. These outcomes might be to enhance or introduce target functional activity for contaminant removal, to avoid hydraulic challenges, or to shape beneficially the downstream microbial community. Moving from the foundational molecular techniques that are commonly applied to biofiltration processes, such as amplicon sequencing and quantitative, real-time polymerase chain reaction, the biofiltration revolution will be facilitated by modern biotechnological tools, including metagenomics, metatranscriptomics, and metaproteomics. The application of such tools will provide a rich knowledge base of microbial community structure/function data under various water quality and operational conditions, where this information will be utilized to select biofilter conditions that promote the enrichment and maintenance of microorganisms with the desired functions.

An examination of the microbial community and occurrence of potential human pathogens in rainwater harvested from different roofing materials.

While harvested rainwater can serve as an alternative water supply, microbial contaminants within the collection system can negatively affect water quality. Here, we investigated the impact of roofing material on the microbial quality of rainwater freshly harvested from pilot-scale roofs (concrete tile, cool, green, Galvalume® metal, and asphalt fiberglass shingle). The microbial quality of freshly harvested rainwater from six rain events over two years was analyzed by high-throughput sequencing and culture-dependent and -independent techniques. The concentrations of total coliform were significantly different among rainwaters harvested from the various roofing materials (p-value >0.05). However, the fecal coliform concentrations and the copy numbers of Enterococcus 23S rRNA genes and total Bacteria 16S rRNA genes did not vary by type of roofing material in a statistically significant way. Potential human pathogens such as Legionella, Escherichia coli O157:H7, Shiga-toxin-producing Escherichia coli, and adenovirus were detected at least once in rainwater harvested from the different roofing materials, even though the lowest occurrence of those potential human pathogens was noted from the metal roof. Also, substantial variation in the microbial communities from the different roofing materials was observed at the family and genus levels. These results demonstrate that the type of roofing material affects the microbial quality of freshly harvested rainwater, indicating that the choice of roofing material could shape the microbial community structure entering a rainwater storage tank. Given that detection of potential pathogens in the freshly harvested rainwater also differed between roofing materials, the type of roofing used to capture rainwater needs to be considered in rainwater harvesting system design, particularly if the water is intended for potable use.

Enzyme-Identified Phosphorus Limitation Linked to More Rapid Headloss Accumulation in Drinking Water Biofilters.

Drinking water biofilters can improve water quality by transforming contaminants or their precursors, but they also can develop headloss more rapidly than do abiotic filters. Phosphorus supplementation has been proposed as one strategy to lengthen biofilter run times, but the impact of this strategy in field tests has been mixed. The current bench-scale study found that severe phosphorus limitation, as indicated by a high phosphatase to total glycosidase activity ratio (PHO:GLY), led to 230% higher headloss accumulation rate when particles were loaded onto the biofilters as compared to the same experiment performed under a mild phosphorus limitation. Phosphorus limitation was associated with higher concentrations of extracellular polymeric substances, lower biomass concentrations, a more filamentous biofilm morphology, and increased relative abundance of Hyphomicrobiaceae (a family of stalked bacteria) on the biofilter media. These differences in the biofilm likely contributed to higher headloss. This work suggests that phosphorus supplementation could improve biofilter hydraulics in the field if the biofilter is severely phosphorus limited, which was indicated by a PHO:GLY greater than 154 under the conditions tested in this study.

Biofilter scaling procedures for organics removal: A potential alternative to piloting.

To provide information for the design and improvement of full-scale biofilters, pilot-scale biofiltration studies are the current industry standard because they utilize the same filter media size and loading rate as the full-scale biofilters. In the current study, bench-scale biofilters were designed according to a biofilter scaling model from the literature, and the ability of the bench-scale biofilters to accurately represent the organics removal of pilot-scale biofilters was tested. To ensure similarity in effluent water quality between bench- and pilot- or full-scale biofilters at the same influent substrate concentration, the tested model requires that either mass transport resistance or biofilm shear loss takes primacy over the other. The potential primacy of mass transport resistance or biofilm shear loss was evaluated via water quality testing (dissolved organic carbon, specific ultraviolet absorbance, liquid chromatography - organic carbon detection, trihalomethane formation potential, and haloacetic acid formation potential). The biofilters also were characterized for adenosine triphosphate (ATP) content, enzyme activity, extracellular polymeric substances, and microbial community structure. The results of this study indicate that biofilm shear loss takes primacy over mass transport resistance for bench-scale biofilter design in this system; thus, bench-scale biofilters designed in this manner accurately represent organics removal in pilot-scale biofilters. Applying this scaling procedure can reduce filter media requirements from many kilograms to just a few grams and daily water requirements from thousands of liters to less than 10 L. This scaling procedure will allow future researchers to test alternative treatment designs and operating conditions without the need for expensive pilot-scale studies.

An improved protocol for extracting extracellular polymeric substances from granular filter media.

Extracellular polymeric substances (EPS) are an important parameter in drinking-water biofilters, and, to date, this is the first study to compare protocols from the literature for extracting EPS from granular filter media. Five extraction protocols were compared, and one was improved by varying the type of initial physical treatment and the shaking intensity, temperature, and time of incubation. Extracting EPS from granular filter media in triplicate by combining 2 g (wet weight) of filter media with 10 mL of extraction buffer (10 mM Tris, 10 mM EDTA, 2.5% NaCl, pH 8), vortexing for 1 min, and incubating for 4 h at 35 °C with shaking at 200 rpm yielded significantly higher EPS polysaccharide and/or protein concentrations than did protocols from the literature. This improved protocol extracted a significant fraction of the biofilm attached to sand but was less effective on biofilm attached to anthracite or granular activated carbon (GAC). A survey of 11 full-scale biofilters from the U.S. and Canada revealed that EPS polysaccharide and protein concentrations can vary over one order of magnitude, from 0.02 to 0.60 mg glucose/g total solids (TS) and 0.27 to 3.38 mg bovine serum albumin/g TS, respectively. Backwashing significantly lowered the biomass and EPS polysaccharide concentrations, but the majority of the biofilm remained attached to the filter media after backwashing, as expected. The fraction of EPS polysaccharides and proteins removed during backwashing did not differ between anthracite and GAC biofilters. The improved EPS extraction protocol can be utilized to investigate the role of EPS in biofilter performance.

Importance of doping, dopant distribution, and defects on electronic band structure alteration of metal oxide nanoparticles: Implications for reactive oxygen species.

Metal oxide nanoparticles (MONPs) are considered to have the potency to generate reactive oxygen species (ROS), one of the key mechanisms underlying nanotoxicity. However, the nanotoxicology literature demonstrates a lack of consensus on the dominant toxicity mechanism(s) for a particular MONP. Moreover, recent literature has studied the correlation between band structure of pristine MONPs to their ability to introduce ROS and thus has downplayed the ROS-mediated toxicological relevance of a number of such materials. On the other hand, material science can control the band structure of these materials to engineer their electronic and optical properties and thereby is constantly modulating the pristine electronic structure. Since band structure is the fundamental material property that controls ROS-producing ability, band tuning via introduction of dopants and defects needs careful consideration in toxicity assessments. This commentary critically evaluates the existing material science and nanotoxicity literature and identifies the gap in our understanding of the role of important crystal structure features (i.e., dopants and defects) on MONPs' electronic structure alteration as well as their ROS-generation capability. Furthermore, this commentary provides suggestions on characterization techniques to evaluate dopants and defects on the crystal structure and identifies research needs for advanced theoretical predictions of their electronic band structures and ROS-generation abilities. Correlation of electronic band structure and ROS will not only aid in better mechanistic assessment of nanotoxicity but will be impactful in designing and developing ROS-based applications ranging from water disinfection to next-generation antibiotics and even cancer therapeutics.

Optimization of growth medium for Sporosarcina pasteurii in bio-based cement pastes to mitigate delay in hydration kinetics.

Microbial-induced calcium carbonate precipitation has been identified as a novel method to improve durability and remediate cracks in concrete. One way to introduce microorganisms to concrete is by replacing the mixing water with a bacterial culture in nutrient medium. In the literature, yeast extract often has been used as a carbon source for this application; however, severe retardation of hydration kinetics has been observed when yeast extract is added to cement. This study investigates the suitability of alternative carbon sources to replace yeast extract for microbial-induced calcium carbonate precipitation in cement-based materials. A combination of meat extract and sodium acetate was identified as a suitable replacement in growth medium for Sporosarcina pasteurii; this alternative growth medium reduced retardation by 75 % (as compared to yeast extract) without compromising bacterial growth, urea hydrolysis, cell zeta potential, and ability to promote calcium carbonate formation.

Mechanistic lessons learned from studies of planktonic bacteria with metallic nanomaterials: implications for interactions between nanomaterials and biofilm bacteria.

Metal and metal-oxide nanoparticles (NPs) are used in numerous applications and have high likelihood of entering engineered and natural environmental systems. Careful assessment of the interaction of these NPs with bacteria, particularly biofilm bacteria, is necessary. This perspective discusses mechanisms of NP interaction with bacteria and identifies challenges in understanding NP-biofilm interaction, considering fundamental material attributes and inherent complexities of biofilm structure. The current literature is reviewed, both for planktonic bacteria and biofilms; future challenges and complexities are identified, both in light of the literature and a dataset on the toxicity of silver NPs toward planktonic and biofilm bacteria. This perspective aims to highlight the complexities in such studies and emphasizes the need for systematic evaluation of NP-biofilm interaction.

Effects of chloride and ionic strength on physical morphology, dissolution, and bacterial toxicity of silver nanoparticles.

In this study, we comprehensively evaluate chloride- and ionic-strength-mediated changes in the physical morphology, dissolution, and bacterial toxicity of silver nanoparticles (AgNPs), which are one of the most-used nanomaterials. The findings isolate the impact of ionic strength from that of chloride concentration. As ionic strength increases, AgNP aggregation likewise increases (such that the hydrodynamic radius [HR] increases), fractal dimension (Df) strongly decreases (providing increased available surface relative to suspensions with higher Df), and the release of Ag(aq) increases. With increased Ag(+) in solution, Escherichia coli demonstrates reduced tolerance to AgNP exposure (i.e., toxicity increases) under higher ionic strength conditions. As chloride concentration increases, aggregates are formed (HR increases) but are dominated by AgCl(0)(s) bridging of AgNPs; relatedly, Df increases. Furthermore, AgNP dissolution strongly increases under increased chloride conditions, but the dominant, theoretical, equilibrium aqueous silver species shift to negatively charged AgClx((x-1)-) species, which appear to be less toxic to E. coli. Thus, E. coli demonstrates increased tolerance to AgNP exposure under higher chloride conditions (i.e., toxicity decreases). Expression measurements of katE, a gene involved in catalase production to alleviate oxidative stress, support oxidative stress in E. coli as a result of Ag(+) exposure. Overall, our work indicates that the environmental impacts of AgNPs must be evaluated under relevant water chemistry conditions.